非傍轴平顶高斯光束M2因子两种定义的比较研究

基于功率密度的二阶矩方法,推导出了非傍轴平顶高斯(FG)光束束宽和远场发散角的解析表达式·研究表明,当w0/λ→0时,远场发散角趋于渐近值θmax=63.435°,与阶数无关·使用非傍轴高斯光束代替傍轴高斯光束作为理想光束,研究了非傍轴FG光束的M2因子,并与传统定义的M2因子作了比较·在非傍轴范畴,非傍轴FG光束的M2因子不仅与阶数N有关,而且与w0/λ有关·按照定义,当w0/λ→0时,非傍轴FG光束的M2因子不等于0,对阶数N=1,2,3时,M2因子分别趋于0.913,0.882和0.886·当N→∞时,M2因子取最小值M2min=0.816·     

The influence of pulse duration on the stress levels in ablation of ceramics: A finite element study

We present a finite element model to investigate the dynamic thermal and mechanical response of ceramic materials to pulsed infrared radiation. The model was applied to the specific problem of determining the influence of the pulse duration on the stress levels reached in human dental enamel irradiated by a CO₂ laser at 10.6 μm with pulse durations between 0.1 and 100 μs and sub-ablative fluence. Our results indicate that short pulses with durations much larger than the characteristic acoustic relaxation time of the material can still cause high stress transients at the irradiated site, and indicate that pulse durations of the order of 10 μs may be more adequate both for enamel surface modification and for ablation than pulse durations up to 1 μs. The model presented here can easily be modified to investigate the dynamic response of ceramic materials to mid-infrared radiation and help determine optimal pulse durations for specific procedures.     

Fundamental processes in long air gap discharges

The development of atmospheric lightning is initiated and sustained by the formation in virgin air of ‘streamer corona’ and ‘leader’ discharges, very similar to those observed in laboratory long sparks. Therefore, the experimental and theoretical investigations of these laboratory discharges have become of large interest to improve the physical knowledge of the lightning process and to develop self-consistent models that could be applied to new protection concepts.In the present paper the fundamental processes of the subsequent phases of long air gap discharges are analyzed, from the first corona inception and development to the leader channel formation and propagation. For all these processes simulations models are discussed that have been essentially derived and simplified by the authors, in order to develop sequential time-dependent simulation of the laboratory breakdown, with both positive and negative voltages. The possibility of extending these models to the case of natural lightning is discussed in the companion paper, presented in this same volume. To cite this article: I. Gallimberti et al., C. R. Physique 3 (2002) 1335–1359.     

Rehabilitation of the Gauss-Jordan algorithm

Summary In this paper a Gauss-Jordan algorithm with column interchanges is presented and analysed. We show that, in contrast with Gaussian elimination, the Gauss-Jordan algorithm has essentially differing properties when using column interchanges instead of row interchanges for improving the numerical stability. For solutions obtained by Gauss-Jordan with column interchanges, a more satisfactory bound for the residual norm can be given. The analysis gives theoretical evidence that the algorithm yields numerical solutions as good as those obtained by Gaussian elimination and that, in most practical situations, the residuals are equally small. This is confirmed by numerical experiments. Moreover, timing experiments on a Cyber 205 vector computer show that the algorithm presented has good vectorisation properties.     

2-fold and 3-fold mixing: why 3-dot-type counterexamples are impossible in one dimension

V.A. Rohlin asked in 1949 whether 2-fold mixing implies 3-fold mixing for a stationary process (ξ_i )_i2ℤ, and the question remains open today. In 1978, F. Ledrappier exhibited a counterexample to the 2-fold mixing implies 3-fold mixing problem, the socalled 3-dot system, but in the context of stationary random fields indexed by ℤ². In this work, we first present an attempt to adapt Ledrappier's construction to the onedimensional case, which finally leads to a stationary process which is 2-fold but not 3-fold mixing conditionally to the σ-algebra generated by some factor process. Then, using arguments coming from the theory of joinings, we will give some strong obstacles proving that Ledrappier's counterexample can not be fully adapted to one-dimensional stationary processes.     

锐钛矿二氧化钛超细纳米晶的三声子互作用

本文通过对粒径为2.2-25.5nm的锐钛矿二氧化钛超细纳米晶在83-293 K温度范围内的变温拉曼光谱的研究,得到了三声子互作用对拉曼频率和线宽的贡献随粒径的变化关系。结果表明锐钛矿二氧化钛超细纳米晶的三声子相互作用随粒径减小而加强。     

光码分多址系统中光学相关接收机判决阈值的分析

介绍了光码分多址系统中常用地址码（一维扩时码、二维码和三维码）的特点，并对它们各自的互相关均值和方差进行了理论分析。基于非相干光码分多址系统中光学相关接收机的基本原理，结合不同的用户地址码，对系统误码率性能进行了分析，得到了接收机最佳判决阈值与地址码基本特性参数和系统同时用户数间的关系。最后，给出了数值仿真结果。结果表明，对于采用特定地址码的光码分多址系统，只有选择合适的接收机判决阈值，系统的误码率性能才能达到最佳。研究结果对光码分多址系统中接收机判决阈值的选取具有一定的参考作用。     

非傍轴平顶高斯光束M2因子两种定义的比较研究

基于功率密度的二阶矩方法，推导出了非傍轴平顶高斯(FG)光束束宽和远场发散角的解析表达式.研究表明，当w0/λ→0时，远场发散角趋于渐近值θmax=63.435°，与阶数无关.使用非傍轴高斯光束代替傍轴高斯光束作为理想光束，研究了非傍轴FG光束的M2因子，并与传统定义的M2因子作了比较.在非傍轴范畴，非傍轴FG光束的M2因子不仅与阶数N有关，而且与w0/λ有关.按照定义，当w0/λ→0时，非傍轴FG光束的M2因子不等于0，对阶数N=1, 2, 3时，M2因子分别趋于0.913,0.882和0.886.当N→∞时，M2因子取最小值M2min=0.816.     

Growth studies of m-GaN layers on LiAlO2 by MOCVD

This paper reports that the m-plane GaN layer is grown on （200）-plane LiAlO2 substrate by metal-organic chemical wpour deposition （MOCVD） method. Tetragonal-shaped crystallites appear at the smooth surface. Raman measurement illuminates the compressive stress in the layer which is released with increasing the layer＇s thickness. The high transmittance （80%）, sharp band edge and excitonic absorption peak show that the GaN layer has good optical quality. The donor acceptor pair emission peak located at -3.41 eV with full-width at half maximum of 120 meV and no yellow peaks in the photoluminescence spectra partially show that no Li incorporated into GaN layer from the LiAlO2 substrate.     

Laser induced copper electroless plating on polyimide with Q-switch Nd:YAG laser

The results of laser induced deposition of copper on polyimide substrate from copper electrolyte solution are reported. Unlike most work reported in the literatures where CW Ar⁺ lasers were used, a second harmonic (532 nm wavelength) Q-switch Nd:YAG laser was used for our experiments. The deposition process was conducted by laser-catalyzing of the polyimide surface and subsequent photothermal-accelerated reduction of copper-complex ions in an alkaline reducing environment. The characteristics of the deposited copper line were investigated in terms of laser beam scanning speed, and the number of scans. The surface morphology and chemical composition of the deposited copper were analyzed using field emission scanning electron microscope (FESEM) and energy dispersive spectrometer (EDX). The optimum processing conditions have been identified. The copper deposit was found to adhere well to the substrate.