变压加载对直接甲醇燃料电池阳极性能的影响（英）

为评价直接甲醇燃料电池（DMFC）阳极的稳定性,利用扫描电化学显微镜和常规电化学技术,研究了变压加载过程中DMFC阳极性能的变化。结果表明,在探针扫描过程中,经不同电压加载后的DMFC阳极表面的扫描电流呈相似的锯齿状分布。当阳极加载2 h,随加载电位升高,扫描峰电流的数量减少,对应峰电流的数值则先增大再减小,表明阳极的催化活性处于不均匀分布状态且随加载时间延长和加载电位升高而逐渐降低。在不同加载电位下,随加载时间延长,循环伏安曲线上的正向和反向电流峰先负移再正移,但抗CO性能持续降低。DMFC阳极在0.6 V下分别加载16 h和72 h后,催化剂粒径由3.4 nm分别增大到3.6 nm和4.4 nm。在0.8 V下加载72 h后,Pt/Ru重量比由2.0增加到3.9。变压加载使催化活性的不均匀分布加剧催化剂粒径长大,Ru流失加快,从而导致阳极催化性能衰减。     

甘油介质在同轴形成线中的击穿特性研究

针对甘油介质在形成线中的应用,总结了甘油作为储能介质已开展的相关研究工作,并在缩比的同轴电极试件中进行了电极表面、磁场、耐压极性、含气量等条件对甘油介质击穿特性影响的实验研究。搭建了基于晶闸管控制的空心脉冲变压器升压实验平台,设计了浸没于脉冲磁场中的同轴电极击穿试件,实验平台最大输出电压500 kV,上升时间26 s,最大磁场1 T,可通过控制晶闸管的先后触发使击穿过程发生于准稳衡磁场中,并制作了外形一致、表面不同的砂纸打磨、羊毛抛光、金属电镀和非金属电镀四种电极。实验结果表明:甘油的击穿是没有极性的;1 T量级磁场对甘油介质的击穿特性无影响;不同电极表面微观形貌差异较大,使甘油介质具有不同的击穿特性,说明甘油击穿在电极表面的过程具有较大影响;充分的排气能减少甘油中直径较大的气泡,减少概率性的低击穿场强,击穿后产生的大量微小气泡会整体降低甘油的击穿阈值,使甘油的平均击穿场强降低。     

直流激励的大气压氩气喷枪的光谱研究

利用正高压驱动空心针-板喷枪装置,通入工作气体氩气,在大气压空气中产生了均匀稳定的喇叭状等离子体羽。电学和光学测量结果表明,放电虽然是在直流电源驱动下工作,但放电为周期性的脉冲。通过对等离子体羽发光信号进行空间分辨测量,研究了脉冲的形成机理,发现除针尖附近的电晕放电外,等离子体羽是以正流光(等离子体子弹)从针尖向着接地电极方向传播的。采用光谱学方法,对电子激发温度随电压的变化及其空间分布进行了测量。结果表明,电子激发温度(约为3 eV)随电压的增大而升高,在一定电压下,电子激发温度沿气流方向也在升高。     

等离子体电极棚电光开关实验研究

 设计建造了以辉光放电形成的等离子体作电极，通光口径为80mm×80mm的普克尔盒实验，实验检测了它的开关性能。阐述了普克尔盒的结构，辉光放电等离子体电极的形成，开关驱动脉冲的产生及输出特性，电光开关的开关效率和开关速度的检测方法，给出了典型的实验结果。     

压电波形对喷墨打印电极的调控规律

压电喷墨打印是制备印刷电子器件的主要手段之一,其墨滴喷射状态直接受压电波形的影响,因而压电波形对于器件打印具有重要意义。本文主要研究了压电波形对薄膜晶体管(TFT)电极打印效果的影响,实验通过改变压电波形的加压速率和脉冲持续时间,打印得到了一系列的电极样品,并对其图形效果及表面粗糙度进行了测量。实验表明,随着加压速率和脉冲持续时间的增大,墨滴喷出动能增大,最终打印的图形效果先改善后恶化,表面粗糙度则随之增大。在加压速率取值为0.08~1.65 V/μs、脉冲持续时间取值为1.216~2.688μs的区间内得到了失真程度较小的电极图形,在加压速率及脉冲持续时间分别为0.25 V/μs、2.688μs及0.65 V/μs、1.600μs时,电极图形化效果较好,表面粗糙度分别为59.04 nm和59.27 nm。通过对压电波形参数的合理设置,能够实现对打印图形效果的优化。     

非水体系中金电极表面增强拉曼光谱研究新进展

利用共焦显微拉曼系统,进行了甲醇溶液中硫氰酸根离子（SCN^-）在金电极上吸附行为的表面增强拉曼光谱（SERS）研究,结果表明：SCN^-与电极之间的相互作用非常强烈,在整个研究电位范围内都可以检测到其SERS信号。在－0．1～－0．6V区间内,SCN^-主要是以S端吸附在电极表面：而在－0．7V～－1．2V区间内,SCN^-主要是以N端吸附在电极表面。     

利用LiF/Al作为电极的有机电致发光器件

本文报道了利用LiF/Al作为负电极的有机电致发光器件,器件结构为ITO/TPD/Alq3/LiF/Al,LiF层的加入增强了电子注入,当其厚度为0.4nm时,器件的性能最好,与单层Al和Mg/Al电极的同类器件相比,此时器件的开启电压由Al电极时的4.3V和Mg/Al电极时的3.0V降低到了2.0V,器件的最大亮度分别由4000cd/m²、14000cd/m²提高到19600cd/m²,器件的发光效率也分别增加了5倍和2倍,达到2.66lm/W.     

Influences of Interface States on Resistive Switching Properties of TiOx with Different Electrodes

Different TiOx thin films prepared by graded or sufficient oxidization of Ti are applied with Pt or Ag electrode in metal？insulator-metal （MIM） structures for studying the properties and mechanisms of resistive switching. The differences on the mobile oxygen vacancies in TiOx films and different work functions of the electrode films result in different insulator-metal interface states, which are displayed as ohmic-like or non-ohmic contact. Based on the interface states, the electrical models for MIM devices are analyzed and extracted. The electrode-limited effect and the bulk-limited effect can be unified to explain the mechanisms for resistive switching behavior as the dominant effect respectively in various conditions. All the current-voltage curves of the four kinds of specimens measured in the experiments can be explained and proved in accordance with the theory.     

Effect of Annealing on Microstructure and Electrical Characteristics of Doped Poly （3-Hexylthiophene） Films

The effect of annealing on the microstructure and electrical characteristics of poly （3-hexylthiophene） （P3HT） films doped with very small amounts of the electron acceptor 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane （F4-TCNQ） is studied. X-ray diffraction and UV-vis spectrum studies show that unlike the pure P3HT film, the thermal treatment on the doped fihns under an Ar atmosphere can effectively enhance the crystalline order of P3HT films, as well as successfully facilitate the orientation of the polymer chains. This improvement is attributed to the electrostatic force between P3HT and F4-TCNQ molecules. This force induces the polymer chains to crystallize and orient during the annealing process. As a result, annealing significantly improves performance, especially for the Ion/Ioff ratio of the TFTs based on the doped P3HT films.     

Electric Field Analysis of Space Charge Injection from a Conductive Nano-Filler Electrode

A simulation on the electric field distribution near the electrode is proposed to explain the reason for using nanosized carbon black mixed with ethylene vinyl acetate, as the electrode could lead to more charge injection into the polymer than using a deposited metal electrode. The electrode is simplified to a layer of conductive semi-spheres with fixed size and constant electric potential. By using the finite element method, it is found that both the size of the semi-spheres and the distance between adjacent semi-spheres could dramatically influence the electric field near the surface of the spheres; these are considered to be the two decisive factors for the charge injecting rate at electrodes of various materials.