低温加氢裂解脱除高硅ZSM-5分子筛内TPAOH模板剂

分子筛膜的合成和应用是近年来的研究热点, 特别是具有独特孔道结构的MFI 型分子筛膜. 但由于膜内有机模板剂在高温脱除时会导致膜产生缺陷, 进而影响分子筛膜的应用. 所以分子筛膜及分子筛晶体中有机模板剂的低温脱除工艺一直是研究者们致力解决的问题之一. 本文系统考察了高硅ZSM-5分子筛晶体内有机模板剂(四丙基氢氧化铵, TPAOH)在H₂/N₂气氛下的低温裂解脱除规律, 采用低温加氢裂解工艺, 在350 ℃以下可有效脱除分子筛晶体孔道内的有机模板剂. 通过对裂解后分子筛晶体的比表面积(BET)、热失重(TG)、傅里叶变换红外(FTIR)光谱和拉曼光谱表征证实, 相比于空气和氮气气氛, 含氢还原性气氛更有利于模板剂的低温脱除, 脱除率随温度的升高而增加; 280 ℃时, 加氢裂解后晶体的BET比表面积已达到252 m²·g^-1, 仍有少量有机残余物; 350 ℃时, 加氢裂解后晶体的BET比表面积可达到399 m²·g^-1, 仅有微量无机碳残余物. 此外, 低温加氢裂解后的分子筛表面相对洁净, 且氨气程序升温脱附(NH₃-TPD)结果表明低温加氢裂解后的ZSM-5 分子筛晶体具有相对较多的酸性位.     

裂解-气相/质谱法分析木屑物证

木屑是一种在各种案件现场中出现几率较高的微量物证,但由于其化学组成复杂、难溶,高分子组分之间的差异不显著,所以一直未建立有效的鉴定方法.采用裂解-气相/质谱技术(PY-GC/MS)对不同树种木屑难溶物进行分析,结果发现:不同树种木屑难溶物的总离子流图特征相似,即每种木屑难溶物的总离子流图中都有一组特征峰.但个别组分有差异.     

《精细化学品催化合成技术(下册):催化合成反应与技术》

《精细化学品催化合成技术》分上、下两册,上册(第1~6章)为"绿色催化技术",下册(第7~14章)为"催化合成反应与技术"。本册(下册)在上册叙述精细化学品合成的绿色催化技术基础上详细介绍了各种类型催化剂参与的各种类型有机     

新型潜香化合物3,6-二甲基-2,5-吡嗪二甲酸二薄荷醇酯的热裂解产物

为开发新型高温释放型烟用香料,以2,3,5,6-四甲基吡嗪和薄荷醇为原料,经过酯化反应制备了3,6-二甲基-2,5-吡嗪二甲酸二薄荷醇酯(DPAME).采用在线热裂解-气相色谱-质谱联用技术(Py-GC-MS)在空气氛围和不同的温度(300、600和900 ℃)下,对DPAME进行热裂解研究,裂解产物经GC-MS进行了定性和半定量分析.结果表明,DPAME在300 ℃下裂解产生了多种有致香效果的醛类、薄荷烯和薄荷醇等;在600 ℃和900 ℃下裂解产生了烯烃类、烷基吡嗪、薄荷醇和薄荷烯等香味物质,并且吡嗪类的种类和相对含量在这两个温度下明显增加.结合DPAME的热裂解产物分析和卷烟感官评吸结果,初步推测了其可能的裂解机理.采用该方法可以方便、快速地分离鉴定物质的热裂解产物,为该物质在烟草中的加香应用提供理论依据.     

高密度烃燃料四氢环戊二烯三聚体的合成及热裂解

以双环戊二烯为原料,经D-A反应及催化加氢合成了高密度烃燃料四氢环戊二烯三聚体(THTCPD).该三聚体的密度为1.082 g/cm3,体积热值为47.5 MJ/L,闪点为120℃,凝固点为48~49℃.采用裂解器与色谱-质谱联用技术,对THTCPD的热裂解进行了在线监测,结果表明温度对裂解反应影响较大.对裂解产物的结构进行了分析,产物以甲烷、乙烯、丙烯、环戊烯、环戊二烯、苯和甲苯为主.依据产物结构及单分子自由基反应模型,推测得到了9种路径的裂解机理.采用X3LYP法进行了各自由基的热力学计算,得到各反应路径的相对能量及路径比.通过不同温度下的裂解转化率,计算得到热裂解反应动力学方程,经线性拟合得到活化能Ea=6.67×104kJ/mol,指前因子A=133.75.     

改性ZSM-5分子筛催化裂解湛江等鞭金藻制取低碳烯烃(英)

研究了湛江等鞭金藻(Isochrysis zhanjiangensis)在改性ZSM-5分子筛上催化裂解制取低碳烯烃的过程.与热裂解过程相比,湛江等鞭金藻催化裂解可以得到更高的低碳烯烃选择性和收率.同时还研究了湛江等鞭金藻中不同油脂和藻渣的催化裂解.结果表明,微藻中的油脂能有效转化为烯烃,其中中性脂的烯烃收率最高,可达36.7%.不同溶剂抽提后得到的藻渣也可转化为低碳烯烃,但收率远低于微藻中的油脂.微藻中的油脂,特别是中性脂,是烯烃的主要贡献者,提高微藻中的中性脂含量能够得到更高的低碳烯烃收率.     

Fractional pyrolysis of Cyanobacteria from water blooms over HZSM-5 for high quality bio-oil production

Fractional pyrolysis and one-step pyrolysis of natural algae Cyanobacteria from Taihu Lake were comparatively studied from 200 to 500 ℃. One-step pyrolysis produced bio-oil with complex composition and low high heating value （HHV〈30.9 MJ/kg）. Fractional pyrolysis separated the degradation of different components in Cyanobacteria and improved the selectivity to products in bio-oil. That is, acids at 200 ℃, amides and acids at 300 ℃, phenols and nitriles at 400 ℃, and phenols at 500 ℃, were got as main products, respectively. HZSM-5 could promote the dehydration, cracking and aromatization of pyrolytic intermediates in fractional pyrolysis. At optimal HZSM-5 catalyst dosage of 1.0 g, the selectivity to products and the quality of bio-oil were improved obviously. The main products in bio-oil changed to nitriles （47.2%） at 300 ℃, indoles （51.3%） and phenols （36.3%） at 400 ℃. The oxygen content was reduced to 7.2 wt% and 9.4 wt%, and the HHV was raised to 38.1 and 37.3 MJ/kg at 300 and 400 ℃, respectively. Fractional catalytic pyrolysis was proposed to be an efficient method not only to provide a potential solution for alleviating environmental pressure from water blooms, but also to improve the selectivity to products and obtain high quality bio-oil.     

CH3O和CO在Pd(111)表面偶联反应机理的理论研究

采用DMol³程序包中的GGA-PW91方法, 结合周期平板模型, 对CH₃O和CO在Pd(111)表面的反应进行了系统研究. 计算结果表明, 吸附在Pd(111)表面顶位上的CO分子中C原子所带正电荷最多, 容易与亲核试剂反应, 化学吸附能稍低, 有利于在表面上移动发生亲电插入反应; CH₃O 在Pd(111)表面fcc穴位吸附稳定, O原子上所带的负电荷较多, 易被亲电试剂进攻. 过渡态搜索表明, Pd(111)表面顶位上的CO与fcc穴位上CH₃O反应生成CH₃OOC的为放热反应, 反应能垒较低, 有利于偶联反应的进行.     

Synergistic effect of W and P on ZSM-5 and its catalytic performance in the cracking of heavy oil

In order to develop the conversion of heavy oil with a high yield of propylene in the catalytic cracking process, ZSM-5 zeolite was modified by tungsten and phosphorus, which was proved to be an effective method. Characterization results show that the improvement of catalytic performance could be correlated to the interaction of phosphorus and tungsten species on ZSM-5. P inhibited the aggregation of tungsten species on ZSM-5 and was conductive to convert the tungsten species with octahedral coordination into tetrahedral coordination. And this ultimately led to that more acid sites were reserved after hydrothermal treatment in the tungsten and phosphorus co-modified ZSM-5 catalyst. Phosphorus species played an important role to restrain the dehydrogenation activity of tungsten. In addition, a model reflecting the interaction between tungsten species and ZSM-5 framework was proposed.     

Mechanism Construction and Simulation for High-temperature Combustion of n-Propylcyclohexane

A detailed mechanism covering 545 species and 3105 reactions for high-temperature combustion of n-propylcyclohexane（n-PCH）, generated via a mechanism generation program（ReaxGen） developed by our research group, was validated in this study. A semi-detailed mechanism involved with 195 species and 573 reactions and a skeletal mechanism concerned with 108 species and 393 reactions were obtained by means of rate-of-production analysis and path flux analysis（PFA）, respectively. In order to validate the reliability of these mechanisms, ignition delay time, laminar flame speed and concentration profiles of important species were simulated with the help of CHEMKIN software. Numerically predicted results of our mechanisms are in very good agreement with available experimental data. Finally, major reaction pathways of n-PCH combustion and important reactions during the combustion process were investigated by reaction pathway analysis and sensitivity analysis, respectively. The results indicate that these mechanisms are reliable for describing the auto-ignition characteristics of n-PCH. These mechanisms would also be helpful to computational fluid dynamics（CFD） for engine design. Moreover, this systematic approach used in our study, which combines mechanism construction, simplification, validation and analysis for n-PCH, may also be employed to construct mechanisms for the high-temperature combustion of other cycloalkanes with one ring.