热解-还原法制备单分散Fe3O4亚微空心球

在用模板法水解FeCl3制备单分散聚(苯乙烯-共-丙烯酸)/Fe2O3[P(St-co-AA)/Fe2O3]核壳粒子的基础上, 于N2环境下热解内核直接得到了单分散的磁性Fe3O4亚微空心球. 用透射电镜(TEM)、场发射扫描电镜(FESEM)、X射线衍射(XRD)、振动样品磁强计(VSM)表征并测试了空心微球的结构形貌、成分以及静磁性能. 结果表明, P(St-co-AA)/Fe2O3核壳粒子在热处理过程中, 由于内核热解生成的有机小分子将Fe2O3 壳层同时还原为Fe3O4, 从而生成了粒径和壁厚均匀的单分散Fe3O4亚微空心球. 该空心微球在室温下的饱和磁化强度、剩余磁化强度和矫顽力分别为50.91 A·m2·kg-1、3.97 A·m2·kg-1和2.33 kA·m-1.     

SHAPE MEMORY EFFECT OF PU IONOMERS WITH IONIC GROUPS ON HARD-SEGMENTS

SMPU （shape memory polyurethane） non-ionomers and ionomers, synthesized with poly（c-caprolactone） （PCL）, 4, 4＇-diphenylmethane diisocyanate （MDI）, 1,4-butanediol （BDO）, dimethylolpropionic acid （DMPA） were measured with cyclic tensile test and strain recovery test. The relations between the structure and shape memory effect of these two series were studied with respect to the ionic group content and the effect of neutralization. The resulting data indicate that, with the introduction of asymmetrical extender, the stress at 100% elongation is decreased for PU non-ionomer and ionomer series, especially lowered sharply for non-ionomer series; the fixation ratio of ionomer series is not affected obviously by the ionic group content; the total recovery ratio of ionomer series is decreased greatly. After sufficient relaxation time for samples stretched beforehand, the switching temperature is raised slightly, whereas the recovery ratio measured with strain recovery test method is lowered with increased DMPA content. The characterization with FT-IR, DSC, DMA elucidated that, the ordered hard domain of the two series is disrupted with the introduction of DMPA which causes more hard segments to dissolve in soft phase; ionic groups on hard segment enhance the cohesion between hard segments especially at high ionic group content and significantly facilitate the phase separation compared with the corresponding non-ionomer at moderate ionic group content.     

二维配位聚合物[K2(5-nbdc)2Cd(Ⅱ)·imH·H2O]∞的合成和晶体结构(英)

The crystal structure of the title complex, [K₂(5-nbdc)₂Cd(Ⅱ)·imH·H₂O]_∞ (5-nbdc=5-nitro-1,3-benzenedicarbonate, imH=imidazole) has been determined by X-ray diffraction analysis. The crystal data are: tetragonal, space group P4₁, M_r=694.93 for CdC₁₉H₁₂N₄O₁₃K₂, a=1.018 6(10) nm, b=1.018 6(10) nm, c=2.436 7(5) nm; Z=4, V=2.528 2(6) nm³, F(000)=1 376, D_c=1.826 Mg·m^-3, μ=1.267 mm^-1. The title polymeric complex exhibits a two-dimensional framework, in which adjacent Cd(Ⅱ) ions are bridged by μ-O₄-5-nitro-1,3-benzenedicarbonate groups forming one-dimensional chains that are further linked by μ-O₃-5-nitro-1,3-benzenedicarbonate groups into two-dimensional anion rectangle sheets with large 32-membered rings. The strong π-π stacks of the benzene rings link these adjacent sheets into a three-dimensional van der Waals network. CCDC: 245527.     

三价锰离子引发烯类单体在聚乙烯醇上接枝聚合的研究

<正> 无论是淀粉;纤维素,还是聚乙烯醇(PVA)的接枝反应,Ce(Ⅳ)被认为是一个十分有效的引发剂,已有较详尽的研究。与Ce(Ⅳ)相类似,Mn(Ⅲ)也可以和一些高聚物组成氧化还原引发体系,由此产生自由基,引发烯类单体在高分子主干上进行接枝聚合。Ranby等人,以焦磷酸络合的三价锰离子引发烯类单体在纤维素和淀粉的接枝反应中,获得了高效的接枝产物。有用这种引发体系在淀粉上接枝丙烯腈获得吸水276     

线性低密度聚乙烯在与丁苯橡胶的共混体系中的结晶行为

本工作采用DSC、X-射线衍射、小角激光光散射、偏光显微镜等手段,研究了线性低密度聚乙烯/丁苯橡胶共混体系中聚乙烯的结晶结构、平衡熔点和结晶动力学。     

聚乙烯醇非均相法环氧乙烷衍生化反应的研究

采用聚乙烯醇与环氧乙烷非均相加合反应合成了不同环氧乙烷结合量的羟乙基化聚乙烯醇（ＨＥＰＶＡ）．在通过１３Ｃ－ＮＭＲ和ＩＲ对产物进行表征的基础上，讨论了反应与ＰＶＡ空间立构性及结晶性间的关系，证明了ＨＥＰＶＡ中聚氧乙烯链的存在，且其含量增长速率随反应深度的增加而增大．     

聚合物微晶尺寸和晶格畸变

聚合物微晶尺寸和晶格畸变是对聚合物材料性能有着重要影响的结构参数。本文介绍了应用Ｘ射线衍射方法测定聚合物微晶尺寸和结构畸变的几种方法：近似函数、次晶模型法、方差法、矩法。     

多组分聚合物体系中的相容和络合

在含可控特殊相互作用的多组分聚合物体系中，随着体系中的相互作用密度的增强，体系在本体中可经历由不相容到相容直至络合的不同物理状态。本文概述了相容、络合研究的进展，着重讨论了相容和络合的区别和联系，提出了含氢键相互作用的高分子共混体系中相容－络合转变存在的普遍性。     

Preparation of polymer-supported phosphine from ferrocene for palladium-catalyzed Suzuki-Miyaura cross-coupling reactions

Polymer-supported phosphine ligand 3b derived from ferrocene was prepared,and applied in palladium-catalyzed Suzuki- Miyaura reactions.A range of aryl bromides can couple with phenylboronic acid to obtain corresponding biaryls in excellent yields. The recycling of the polymer-bound catalyst was tested without adding palladium.     

一种新型锂离子电池用聚合物电解质复合膜的制备和性能表征

阐述了一种新型锂离子电池用PVDF-HFP(聚偏氟乙烯-六氟丙烯聚合物树脂)基聚合物电解质复合膜的制备过程. 对复合膜中使用的无机TiO2纳米颗粒进行固体超强酸化处理, 并进行颗粒表面酸强度H0测试、XRD晶体结构分析以及复合膜的电解液吸附率测试和电化学阻抗谱测试. 采用PE无纺布支撑体作为增强材料, 以浸涂方法制备复合膜,并进一步组装为锂离子电池, 性能测试表明该电池具有良好的电化学性能.