制备方法对Mg1.9Al0.1Ni合金储氢性能的影响

文中采用机械合金化(MA)和氢化燃烧法(HCS)制备了Mg1.9Al0.1Ni,通过对它们储氢性能的对比研究发现,MA优于HCS.采用MA制得的Mg1.9Al0.1Ni储氢合金具有较高的活性和高储氢量,对PCT结果进行计算,得出温度和氢平衡压的关系式.Mg1.9Al0.1Ni(MA)553K时100s内吸放氢量分别为2.67和2.54 mass%H.用XRD方法进行物相分析,表明添加适量Al没有改变Mg2Ni的物相结构,由于MA能够制备出纳米晶粒,使得Mg1.9Al0.1Ni合金具有更好的储放氢动力学性能.     

磁化作用对汽油动态挥发性影响的研究

用热重（TG）分析和自行设计的原位动态挥发实验，研究了在不同条件下汽油的挥发性，结果表明，磁化空气或磁化汽油都可提高汽油的挥发性，而汽油和空气共同磁化，可更大幅度地提高汽油的挥发性。     

氧瓶燃烧甲基百里酚蓝法测定有机物中硫含量

1 引言 有机硫的测定在有机微量定量分析中颇占重要地位。我们采用氧瓶燃烧分解有机硫元素成硫酸根离子,继而测定之。尽管测定硫酸根离子方法很多,但每种方法均有其不足之处。用甲基百里酚蓝(MTB)测定硫酸根在国外曾有报道,而国内还是空白。我们选择了该方法做了些工作,为我国有机硫测定增加一种可选择的方法。     

PREPARATION OF CUO/γ-Al2O3 CATALYSTS FOR CATALYTIC COMBUSTION VOCS VIA PLASMA

CuO/γ-Al2O3 catalysts were prepared by plasma treatment and conventional impregnation methods. The catalytic combustion of two kinds of volatile organic compounds (VOCs), toluene and benzene, were carried out over these CuO/γ-Al2O3 catalysts. The surface properties of these catalysts were characterized by X-ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). The experimental results showed that in catalytic combustion the activity of the CuO/γ-Al2O3 catalyst prepared via plasma was much higher than that of the CuO/γ-Al2O3 catalyst prepared by conventional impregnation method. XRD results showed that an enhanced dispersion had been achieved with the plasma treatment. SEM results indicated that the size became much smaller and the surface became more uniform with the plasma treatment.     

卟啉化合物的热化学研究: V. 含溴卟啉化合物的标准燃烧能和生成焓

用本实验室建立的精密转动氧弹燃烧热量计测定了标准物质对溴苯甲酸、辅助物质鲨烷及四对溴苯基卟啉(Tp-BrPP)的标准燃烧能, 并计算出了它们的标准生成焓。     

Effect of Drying Methods on the Structure and Combustion Activity of Mn—Substituted Hexaaluminate Catalysts

Conventional oven drying (COD) and supercritical drying (SCD) methods were applied to the preparation of Mn-substituted hexaaluminate (BaMnA111O19-α) catalysts. The effect of drying methods on phase composition, specific surface area, pore structure, reduction behavior of Mn^3 ions, and combus-tion activity of the samples was investigated. The homogenous mixing of the components in the sol-gel process could be maintained by SCD, and the hexaaluminate phase was almost the only phase of the resulting materials after calcination. H2-TPR revealed that the Mn^3 ions in the sample obtained by SCD were easier to be reduced than that by COD. Moreover, the samples obtained by SCD have higher surface area, narrower pore size distribution, and higher combustion activity than those obtained by COD.     

逆微乳液法合成六铝酸盐甲烷燃烧催化剂

采用逆微乳液为媒介合成六铝酸盐及其金属取代系列甲烷燃烧催化剂.首先研制了由表面活性剂、助剂、油相和水相四组分逆微乳液拟三元体系相图,选择十六烷基三甲基溴化铵(CTAB)为表面活性剂,脂肪醇为助剂,正辛烷为油相和水相[或Al(NO3)3溶液].研究了助剂脂肪醇链长、表面活性剂与助剂相对量和盐浓度对微乳液体系形成和稳定性影响,并以电导率随水含量变化的规律很好地印证了微乳液体系的相行为.选取相图中稳定微乳区合成了具有高温稳定性的甲烷催化燃烧催化剂六铝酸镧[La(Mnx/Fex)Al12-xO19-δ].用BET、TG-DTA和XRD表征了催化剂的物性和结构,并在微型固定床反应器中考察了对甲烷燃烧的催化活性.结果表明,利用逆微乳液作为反应介质使催化剂前驱体分散更充分,使六铝酸盐晶相形成的温度有效地降低到950℃.Fe取代的六铝酸盐具有较好高温催化活性和热稳定性,而Mn取代的同晶体则具有较好的低温催化活性,Fe和Mn离子同时对Al3 进行取代时,由于两者之间存在的协同效应明显提高了催化剂的催化活性和比表面,T10仅为475℃,T90为660℃.     

油烟污染及其排放控制技术

烹调油烟已经成为城市三大公害之一, 对环境和人体健康造成了巨大危害, 油烟治理势在必行. 本文介绍了油烟的组成、分析方法和主要危害, 阐述了各类油烟净化技术的技术特点, 分析了油烟净化的国内外研究动态, 指出催化燃烧技术是油烟污染控制技术的发展趋势.     

氧瓶燃烧—冷原子吸收法测煤样中痕量汞

采用氧瓶燃烧－针筒注射－冷原子吸收法测煤样中痕量汞，并对测定条件进行研究。方法简便、快速、干扰少，汞含量在０￣１０．０ｎｇ／５０ｍｌ时遵守比耳定律。用于样品的测定，结果令人满意。     

氧弹燃烧灰化法测定有机物中磷

用氧弹燃烧法灰化有机物进行元素测定，操作简便，快速，无污染，该方法用于有机物中磷的分析，结果可靠。