Toughening of polycarbonate through reactive melt blending: Effect of hydroxyl content and viscosity of hydroxyl-terminated polydimethysiloxane

In this study, four hydroxyl-terminated polydimethylsiloxanes(PDMSOH) with different viscosities and hydroxyl contents were used to improve the toughness of polycarbonate(PC) through reactive melt blending. A largely improved toughness of PC has been achieved, and the low temperature toughness of PC/PDMSOH blends could overtake that of PC homopolymer in much higher temperatures(e.g.-10 °C versus 23 °C). Moreover, it was found that the more the hydroxyl content, the less the PDMSOH was needed to reach the highest toughness, suggesting that equivalent molar ratio between the carbonyl group content of PC and the hydroxyl group content of PDMSOH was required for the toughening of PC. Ultraviolet spectrophotometry was used to analyze the possible reaction between PC and PDMSOH. Contact angle was measured to assess the change of interfacial interaction between PC and PDMSOH as change of viscosity and hydroxyl content. The formation of PC-co-PDMSOH copolymer was believed to be the key for the toughening effect. This work gives a profound recommendation of the optimum kind and dosage of PDMSOH which should be used to improve the toughness of PC and will find immediate industrial applications.     

Studies on crystal transition of polyamide 11 nanocomposites by variable-temperature X-ray diffraction

Polyamide I1 （PAll） and its nanocomposites with different organoclay loadings were prepared by melt-compounding and subsequent pelletizing. The crystal phase transitions of PAl 1 and its clay nanocomposites were investigated by variable-temperature X-ray diffraction. It was found that the Brill transition of the nanocomposite was 20 K higher than that of the neat PAl 1 for both heating and cooling processes. The PAl 1 d-spacings of the nanocomposites were observed to be smaller than those of the neat PAl 1 for melt crystallization. The constraints imposed by the addition of layered clay, restricting the thermal expansion of the polymer chains, are probably responsible for such a reduction of the d-spacing.     

复杂应力状态下GCr15轴承钢的动态剪切及熔融特性研究

本文探究了GCr15轴承钢压剪试样在冲击载荷下的绝热剪切和熔融破坏特性．首先,实验研究发现GCr15轴承钢的力学性能具有拉-压不对称性、应力状态及应变率敏感性．因此,通过引入应力三轴度、洛德角、应变率和绝热剪切温升机制扩展了经典J-C本构模型,并对GCr15轴承钢的动态单轴压缩和压剪试验结果进行了数值实现．研究结果表明,应力三轴度和洛德角是影响动态冲击下压剪试样的绝热剪切产生和熔融特性的重要因素．     

聚乳酸熔体纺丝、粘接和吸附性能的初步研究

针对制备香烟过滤嘴用丝束和过滤嘴棒的特殊需要,研究了聚乳酸的纺丝、粘接和吸附性能,通过流变学测量考察了各种加工因素对熔体流动性和可纺性的影响,特别是残留水分的影响,用分子量、DSC和力学性能测量跟踪了熔体纺丝和后加工过程.所获结果对确定聚乳酸树脂的规格范围,确定纺丝和后加工工艺,具有参考价值.     

YJ-3000t型紧装式六面顶大腔体高温高压实验装置样品室的压力标定

 在温度为389~1 245 ℃和砧面压力为1.0~5.0 GPa的条件下,利用金属高压熔融标定法,采用Cu、Al、Zn和Pb四种金属,对YJ-3000t型紧装式六面顶大腔体高温高压实验装置样品室内的实际压力进行了标定。通过对由四种金属所获得的标定结果的多项式三维模拟,获得了以叶蜡石为外传压介质、氧化铝为内传压介质的情况下,由砧面压力和样品室温度估算样品室内实际压力的定量表达式。该结果可为今后该设备上类似实验组装中样品腔内实际压力的估算提供方便准确的压力标。     

成核剂含量对β晶相聚丙烯结晶与熔融行为的影响

用DSC研究了β成核剂含量对β聚丙烯在等温与非等温结晶条件下的结晶与熔融行为的影响,发现当成核剂含量为0.005％时,结晶焓△H_c、β晶的熔融焓△H_(mβ)及熔点T_(mβ)均为最大,而α晶的相对含量最小.广角X-衍射数据表明,成核剂含量高的试样的(301)衍射峰的相对强度下降,反映分子链排列的纵向有序性降低.根据聚丙烯分子在β成核剂上附生结晶的成核机理解释了上述结果.     

脉冲加热惰气熔融-热导法测定焦粉中氮的含量北大核心CSCD

近年来钢铁行业发展迅速,同时环境污染问题日益突出,烧结烟气污染物主要是硫化物和氮化物等,目前烧结工序强制性配套了脱硫装置,烧结烟气中硫化物能够达到排放要求。由于工业上使用的脱硝装置成本过高及脱硝方式的不成熟[1],大部分烧结工序都没有安装氮氧化物脱除装置。而烧结过程中一般使用焦粉为燃料,如果焦粉中氮含量过高会导致烧结烟气中氮氧化物过高,如果氮氧化物含量超标则会导致烧结停机,对生产运行造成较大影响,因此对焦粉中氮含量的监测尤为重要。     

惰气熔融-热导法测定钕铁硼永磁材料中的氢

建立惰气熔融-热导法测定钕铁硼永磁材料中氢的分析方法。当氧-氢比例大于50:1时,CO对氢的测定结果产生一定的干扰,加入舒茨试剂可消除此干扰。采用标准坩埚,称样0.05g,熔融功率为2.85 kW,选择高纯镍篮和锡片做助熔剂,钕铁硼中氢释放完全。以普通钢铁参考物质建立氢校准曲线,线性相关系数r～2=0.9999,检出限为0.75μg/g。该法用于钕铁硼样品中氢的测定,测定结果与脉冲熔融飞行时间质谱-气体元素分析仪测定结果基本一致,测定结果的相对标准偏差为1.4%(n=5)。该方法可以准确测定钕铁硼永磁材料中的氢,能满足日常分析的要求。     

Li2B4O7坩埚内预氧化熔融铸片XRF法测定含还原物耐火材料中主量和次量组分

在四硼酸锂坩埚中,以碳酸锂和硝酸铵为氧化剂,在铂金坩埚外对含还原物耐火材料进行预氧化和烧结。在高温氧化过程中,由于样品表面包裹有含氧化剂为主的烧结物,在继续熔融氧化产生的气体浮力作用下,样品在未被氧化前,不与铂金坩埚接触。因此,避免了熔融过程中铂金坩埚腐蚀问题。实验结果表明,氧化温度控制在730℃以下,时间15min内,含还原物耐火材料样品与氧化剂发生氧化烧结反应,四硼酸锂坩埚不会熔穿。确定的预氧化温度为720℃,时间为5~15min。结合现有的报道,确定了熔融铸片所需氧化剂和脱模剂的用量、熔融温度和时间。按拟定的方法,用国家和行业标准样品绘制工作曲线,对含还原物耐火材料样品进行了测定。与湿法分析结果进行比较表明,准确度与湿法分析相当。     

防锈颜料三聚磷酸铝的拉曼光谱研究(英文)

应用拉曼光谱研究了含有防锈颜料涂装特性的钢样 ,在此基础上探讨了三聚磷酸铝防锈颜料对A3钢的保护机理 .三聚磷酸铝溶解后能到达钢样表面 ,其离子可与铁离子化合形成三聚磷酸铁 .三聚磷铁能缓慢地通过化学键牢固地附着在钢样表面 ,最终在钢表面形成一层隔绝腐蚀介质和钢样的紧蜜保护膜阻止了腐蚀的继续发生从而达到保护的目的