水嘴国标对17种重金属析出量强制限定

<正>质检总局和国家标准委不久前发布了新修订的《陶瓷片密封水嘴》(GB 18145–2014)强制性国家标准,将水嘴的重金属析出、密封性能、流量、寿命作为强制性条款,其中重金属析出一款对17种重金属析出规定了严格的限量值。新标准将于2014年12月1日实施。据国家标准委有关人士介绍,随着经济发展和社会进步,我国城乡居民对健康安全的要求越来越高。为满足健康安全需求,国家标准委高度重视水嘴铅超标问题,委托全国建筑卫生陶瓷标准化技术委员会组织行业专家、检验机构、     

低温热分析标准物质的研制

研制了两种0~100℃热分析标准物质,分别为金属镓和水杨酸苯酯标准物质。研制的标准物质具有良好的均匀性和稳定性,采用与NIST,LGC相应标准物质比较的方法定值。NIST为SRM 2234镓,其定值采用288.6~314.35 K范围内的绝热热量计测得温度及热量值;LGC用绝热法为水杨酸苯酯的熔化温度和熔化热定值,两种方法都可以直接溯源至SI单位。对定值结果的不确定度进行了分析和评定。镓和水杨酸苯酯标准物质的熔化温度分别为(29.77±0.20)℃(k=2),(41.81±0.34)℃(k=2);熔化热分别为(80.52±0.48)J/g(k=2),(88.94±0.62)J/g(k=2)。研制的两种标准物质满足国家标准物质的技术要求,申报已获批准。     

二异丁腈肼溶液中氮的选择性测定

二异丁腈肼分子结构中含有连氮(-N-N-)和氰基氮(-CN),每一个分子中有4个N原子,其结构式见图1。油溶性偶氮引发剂偶氮二异丁腈是重要的化工原料,广泛用于高分子的研究和生产,可作为氯乙烯、乙酸乙烯和丙烯腈等单体聚合引发剂,也可用作聚氯乙烯、聚烯烃、聚氨酯、聚乙烯醇、丙烯腈与丁二烯、苯乙烯共聚物等的发泡剂。此外,也可用于其它有机合成。偶氮二异丁腈由氯气氧化二异丁腈肼而制得,这开发了偶氮二异丁腈生产的新工艺,达到清     

Rapid,simple and selective determination of 2,4-dinitrophenol by molecularly imprinted spin column extraction coupled with fluorescence detection

A rapid, simple and selective method based on molecularly imprinted, spin column extraction coupled with fluorescence detection was successfully established for the determination of 2,4-dinitrophenol in serum samples. The 2,4-dinitrophenol imprinted polymers exhibited highly selective recognition for the template molecule and the maximum adsorption capacity was 138.9 mg/g. The results indicated that when water is used as the loading solution, only 2,4-dinitrophenol could be adsorbed on the spin column without the remaining structural analogs（2-nitrophenol, 4-nitrophenol and phenol）. After eluting with acetonitrile/acetic acid（9/1, v/v）, 2,4-dinitrophenol in serum samples could be determined by using the fluorescence spectrometer, based on the fluorescence enhancement of fluorescein by the template molecule. Under the optimal conditions, the spiked recovery ranged from 95.8% to 103.4% and the detection limit was 1 nmol/L. The results confirmed the reliability and practicality of the protocol and revealed a good perspective of this method for biological sample analysis.     

Electrospinning of nylon-6,6 solutions into nanofibers: Rheology and morphology relationships

The relationship between the rheological properties of nylon-6,6 solutions and the morphology of their electrospun nanofibers was established. The viscosity of nylon-6,6 in formic acid(90%) was measured in the concentration range of 5 wt%-25 wt% using a programmable viscometer. Electrospinning of nylon-6,6 solutions was carried out under controlled parameters. The chemical structure, morphology and thermal properties of the obtained nanofibers were investigated using Fourier transform infrared spectroscopy(FTIR), scanning electron microscopy(SEM) and differential scanning calorimetry(DSC), respectively. Entanglement concentration(ce) was found to be 15 wt% and a power law relationship between specific viscosity and solution concentration was observed with exponents of 2.0 and 3.3 for semi-dilute unentangled(c ce) and semi-dilute entangled(c ce) regimes, respectively. The diameter and uniformity of the nanofibers were found to be dependent on the viscosity. Moreover, the average diameter of electrospun nanofibers was found to be dependent on zero shear rate viscosity and normalized concentration(c/ce) in a power law relationship with exponents of 0.298 and 0.816, respectively. For nylon-6,6 solutions, the entanglement concentration(ce = 15 wt%) provides the threshold viscosity required for the formation of a stable polymeric jet during electrospinning and producing uniform beadless fibers. For concentrations less than ce, beaded fibers with some irregularities are formed. DSC analysis showed an increase in crystallinity of all electrospun samples compared to original polymer. Furthermore, Based on FTIR spectroscopy, α phase is dominant in electrospun nanofibers and minor amount of β and γ phases is also available.     

Microstructure characterization of short-chain branching polyethylene with differential scanning calorimetry and successive selfnucleation/annealing thermal fractionation

A series of the copolymers of ethylene with 1-hexene(M1–M9) synthesized by metallocene catalyst Et[Ind]2ZrCl2/MAO was studied by differential scanning calorimetry and successive self-nucleation and annealing(SSA) thermal fractionation. The distribution of methylene sequence length(MSL) in the different copolymers was determined using the SSA method. The comonomer contents of samples M4 and M5 are 2.04 mol% and 2.78 mol%, respectively. Both M4 and M5 have low comonomer content and their MSL distribution profiles exhibit a monotonous increase trend with their MSL. The longest MSL of M5 is 167, and its corresponding molar percent is 43.95%, which is higher than that of M4. Moreover, the melting temperature(Tm) of M5 is also higher than that of M4. The comonomer contents of samples M7, M8, and M9 are 8.73 mol%, 14.18 mol% and 15.05 mol%, respectively. M7, M8, and M9 have high comonomer contents, and their MSL distribution profiles display unimodality. M7 has a lower peak value of 33 and a narrow MSL distribution, resulting in a Tm lower than that of M8 and M9. The MSL and its distribution are also key points that influence the melting behavior of copolymers. Sometimes, MSL and its distribution of copolymers have a greater impact on it than the total comonomer contents, which is different from traditional views.     

差示扫描量热法测定比沙可啶的纯度

建立差示扫描量热法测定比沙可啶原料药样品纯度的方法。考察了炉体气氛、升温速率、称样量3个因素对差示扫描量热法测定结果的影响,确定差示扫描量热法最佳实验条件:升温速率为2.0 K/min,称样量为2.0~4.0 mg,炉内气体为静态空气。差示扫描量热法测定比沙可啶样品纯度为99.86%,测定结果的相对标准偏差为0.02%(n=6),差示扫描量热法测定比沙可啶样品纯度值与HPLC测定结果具有良好的一致性。该方法可以快速、准确地测定比沙可啶化学纯度,为比沙可啶纯度测定提供了一种新的分析方法。     

任意边界条件下双模量矩形薄板的弯曲

将双模量板等效为两个各向同性小矩形板组成的层合板,假定该层合板的中性面即为两个小矩形板的交界面。根据中性面上应力为零且薄板全厚度上应力的代数和为零,推导了双模量矩形薄板的中性面位置。本文采用严宗达提出的带补充项的双重正弦傅里叶级数通解,该通解可以适用于任意边界条件的矩形薄板且不需要叠加或者重新构造。联立边界条件和控制方程,求得通解中的待定系数并代入到通解中,即可得到任意边界条件下双模量矩形薄板的弯曲解析解。与有限元结果比较,本文结果符合工程精度要求。     

40W/20K单级G-M制冷机设计与研究

目前商用G-M制冷机在20K时的制冷量一般小于10W,然而工业界对20K时具有更大制冷量的制冷机需求正在不断增长。文中对影响单级G-M制冷机制冷量的因素进行分析,提出相应的解决措施;并针对高温超导应用技术和一些低温系统工程项目的需求,设计了40W/20K单级G-M制冷机样机。     

碱金属及碱土金属离子化合物溶解性变化规律

对碱金属、碱土金属离子化合物的溶解性与正负离子半径差Δr的变化关系进行了探讨,总结出碱金属、碱土金属同族化合物溶解性随Δr的变化有以下3种情况:(1)随Δr增大,溶解度s随之增大;(2)随Δr增大,s反而减小;(3)随Δr增大,s变化不规则。在此基础上,通过碱金属、碱土金属同族化合物晶格能U、离子水合焓ΔHh、溶解过程的焓变ΔHs和自由能变ΔGs等热力学量的递变对其溶解性随Δr的变化作出了解释。