Efficient Visible Electroluminescence from Porous Silicon Diodes Passivated by Carbon Films

By using n-butylamine as a carbon resource,carbon film is deposited on the p-n porous silicon (PS) surface with a radio-frequency glow discharge plasma system.Raman spectra and infrared reflection (IR) spectra of the carbon films indicate that there are amine-group and hydrogen atoms therein.The IR spectra of the passivated PS samples exhibit that the PS surfaces are mainly covered with Si-C,Si-N and Si-O bonds.Electroluminescence (EL) spectra show that the EL intensity of the passivated PS diodes increases greatly and the blueshift of the EL peak occurs compared with the diodes without treatment.Both of these are stable while the passivated diodes are exposed to the air indoors.The I-V characteristics reveal that the passivated diodes have a smaller series resistance and a lower onset voltage.The influence of the carbon film passivation on EL properties of PS has also been discussed.The results have proven that carbon film passivation is a good way to enhance the PS luminescent intensity and stability.     

POROSITY CALCULATION OFMIXTURES OF FIBROUS PARTICLES

The initial forming of fiber blend to high green density, i.e. the packing of fibrous particles, is important to the reinforcement of composite materials. It is very useful to develop a general predictive method for the optimum selection of particle mixtures for the property control of ceramic or composite products. This paper presents such a mathematical model developed on the basis of the similarity analysis between the spherical and non-spherical particle packings and assesses its applicability to the packing of fibrous particles with discrete and/or continuous length distributions. The results indicate that the model can predict this packing system well and hence provide an effective way to solve various packing problems in the composite materials processing.     

多孔硅制备过程中B,P杂质原子的作用

采用DV-Xα方法对多孔硅形成过程中位于表层的B和P杂质原子的作用进行研究,结果表明位于顶层硅原子层中的B和P杂质原子均可削弱其邻近的Si-Si键强度,因而可能导致出现腐蚀的突破点,再通过分析杂质对表面区势场的改变,可以认为位于顶层硅原子层中的B杂质原子产生腐蚀的突破点的可能性更大。 关键词：     

用激活性非线性介质Nd：MgO：LiNbO3产生二次谐波

以Nd:MgO:LiNbO_3同时兼作激活介质和非线性光学材料,研究自倍频激光器。用小型氙灯泵浦,在室温下获得二次谐波激光(0.547μm) 阈值小于4.8'J,最大输出400μJ/shot,工作温度范围大于20℃～45℃,无光损伤。     

氩气介质阻挡放电的发光特性

本文使用水电极介质阻挡放电装置,采用光学方法测量了氩气介质阻挡放电的发光特性。发现在驱动电压处于一定的范围内时,放电处于丝极模式,在驱动电压的每半周期内,无论是放电的总光还是单个微通道的放电发光均只有一次脉冲,单个微放电的时间为2μs,而总放电时间为2.4μs,这表明在氩气的丝极模式中,各单丝产生与熄灭的时间极其接近,各个放电丝之间有着很好的时间相关性。最后将本文的结果与空气中介质阻挡放电丝极模式的发光特性相比较,空气放电在每半周内的总光信号由多个脉冲组成,而每一个脉冲对应多个放电丝,因而氩气中各个放电微通道之间的时间相关性远强于空气的情况。     

Lattice Boltzmann方法模拟多孔介质Klinkenberg效应

格子Boltzmann数值模拟方法是研究复杂的多孔介质结构特别是Klinkenberg效应的有效方法之一，对处理复杂边值问题尤其有效，用格子Boltzmann方法研究了气流穿越多孔介质问题，并将数值计算结果与实验结果进行了比较，结果表明格子Boltzmann方法是数值模拟气流穿越多孔介质问题的有效方法之一。     

Instability of Solitary Waves in Nonlinear Composite Media

In this paper,we investigate a class of Hamiltonian systems arising in nonlinear composite media.By detailed analysis and computation we obtain a decaying estimates on the semigroup and prove the orbitalinstability of two families of explicit solitary wave solutions (slow family in anisotropic case and solitary wavesin isotropic case),which theoretically verify the related guess and numerical results.     

激光介质的多次吸收不均匀内热源模型

针对激光介质的内热源,以多次吸收作用为基础提出了适用于侧面双向泵浦板状激光介质的不均匀内热源模型,即多次吸收不均匀内热源模型,并与均匀内热源和一次吸收内热源模型进行了对比分析。研究表明,介质厚度及光吸收系数组成的无量纲参数不同时,三种内热源模型得到的内热源分布也有所不同。最后给出了内热源不均匀度及多次吸收模型与一次吸收模型之间的差异在不同目标值下的内热源模型适用准则。     

周期性分层介质高反射区范围的分析与估计

对于具有周期单元的分层介质材料高反射区的波长范围，提供一种简明的估计分析方法.基于Floquet定理，分析了有限周期单元分层介质的光子带隙特性，给出分层介质的高反射区波长范围.讨论了分层介质高反射区和周期单元禁带之间的关系.计算表明，高反射区和周期单元禁带的中心波长彼此一致.并且，随着分层介质周期单元数的增多，高反射区的深度和带宽就越接近于周期单元禁带的深度和宽度.最后，讨论周期分层介质的光子带隙特性与入射角及其与极化的变化关系. 关键词： 分层介质 带隙特性 周期单元 高反射区     

二维随机激光器的模式选择及阈值与饱和特性

基于将Maxwell方程与四能级原子系统速率方程相结合而建立起随机激光时域理论，并利用有限时域差分法，研究了二维随机介质中激光模式的输出特性与介质尺寸、外形及抽运速率等参数的关系.结果表明，与传统激光模式相似，随机激光模式的强度随抽运速率的变化不仅具有阈值特性，而且具有饱和特性.基于模式特性对介质及抽运参数的依赖关系，提出了二维随机激光器的选模方式，在很大程度上不同于传统激光器的选模方式. 关键词： 随机激光器 模式选择 无序介质中的光学特性