微波合成铝掺杂钻酸锂材料及性能研究

以LiOH·H2O，Al2O3和Co3O4为原料，微波加热合成Li离子电池正极材料LiAlxCo（1-x）O2．通过XRD测试表征了不同Al加入量时合成产物的晶体结构，确定当x≤0．4时，产物为单一相层状结构．计算了不同x时LiAlxCo（1-x）O2的晶胞参数，随着x的增大，a值减小，c值增大．对合成LiAlxCo（1-x）O2样品进行DSC—TGA测试，结果表明，当x不同时，合成样品的热稳定性不同．SEM测试表明，合成晶体粒度较均匀，粒径在5μm左右．电化学测试表明，LiAl0.2Co0.8O2的电化学性能最好，首次循环放电容量为127mAh／g，多次循环容量损失率小于LiCoO2．     

在线标准加入火焰原子吸收光谱法测定钮扣电池中铅和镉

应用火焰原子吸收光谱(FAAS)法测定了钮扣电池中铅和镉的含量,对测定条件作了较详细的研究。用在线双毛细管标准加入法消除了基体的干扰。按所述方法测定电池样品中铅和镉,测定结果的RSD依次为3.58%和5.87%,铅和镉的浓度水平分别为5.4×10-3%和2.3×10-4%(质量分数),回收率结果为93.0%~100.1%(铅)和95.0%~101.0%(镉)。     

氯化钠对锂离子电池石墨负极的修饰改性

Numerous carbonaceous materials have been studied as anodes of lithium ion batteries during the past several years[1￣4].Graphite was favored for battery applications because it exhibits a high specific capac- ity, low working potential close to that of l…     

掺杂Y^3+的锂锰尖晶石的合成及其电化学性能研究

采用流变相反应法合成了掺杂稀土钇离子的锂锰尖晶石LiYxMn2-xO4，并对其 结构和电化学性能进行了初步研究。结果表明，当掺入的Y^3+的含量较低（x≤0. 02)时，得到的产物能保持完整的尖晶石结构，并表现出极佳的电化学性能。Y^3+ 的掺入使材料的循环稳定性能大幅度提高，而这种提高是源于Y^3+对尖晶石结构的 稳定作用。电极材料LiY0.02Mn1.98O4显示了最优的电化学性能，在0.2℃放电速率 下，其初始放电容量为118mA·h·g^-1，100次循环后仍能保持初始容量的98％。     

高温固相法合成LiNi1/3Mn1/3Co1/3O2及其性能研究

采用高温固相法合成出层状锂离子电池正极材料LiNi_1/3Mn_1/3Co_1/3O₂。通过XRD、ICP、SEM和电化学测试手段对产物的结构、组成、形貌及电化学性能进行了研究。XRD结果表明此方法合成的LiNi_1/3Mn_1/3Co_1/3O₂具有标准的α-NaFeO₂型层状结构，SEM照片显示颗粒粒径大约在500 nm左右，粒径分布较窄。以20 mA·g^-1电流密度放电，充放电电压在2.8～4.4 V之间，其首次放电比容量为170 mAh·g^-1，40次循环容量保持率为85.3%。进一步加入石墨导电剂后，同样条件下首次放电比容量变为179 mAh·g^-1，50次循环容量保持率为89.6%。容量衰减主要发生在前10次循环。XRD和SEM测试表明循环初期容量衰减的原因是由材料本体结构变化和界面反应共同作用的结果。     

利用湿法反应制备的LiV3O8的锂离子扩散特性

利用V2O5•nH2O湿凝胶和Li2CO3作原料,通过溶液反应和低温焙烧的方法合成了用于锂离子电池正极的LiV3O8.对其前驱体和产品分别进行DTA-TG、XRD表征.LiV3O8用作锂离子电池正极的电化学性能利用恒电流充放电测试进行研究.实验表明活性材料LiV3O8具有较高的充放容量和良好的循环性能.LiV3O8电极的锂离子化学扩散系数由恒电位间歇滴定技术(PITT)来确定，其值依据Li1＋xV3O8中x值的不同在10－8～10－10 cm2•s－1的变化范围内.获得的锂离子的扩散活化能为：Ea=25～42 kJ•mol－1(x=0.18～2.5).认为锂离子扩散的最大活化能是由锂离子在Li4V3O8相中的扩散决定的.     

相变材料耦合冷板电池热管理系统的优化设计

以相变材料耦合冷板电池热管理系统为研究对象,采用数值方法研究了系统的冷却性能。结果表明,通过增加耦合系统的冷却水流量可以降低电池组温度和温差,但是显著增加了冷板功耗,系统能效较低。为了提高耦合热管理系统的冷却效率,在固定系统体积的情况下,采用优化策略对系统中相变材料的厚度分布进行调整。典型算例结果表明,优化策略仅需5步调整就能得到最佳相变材料厚度分布。相比于优化前系统,优化后的系统使电池组最高温度降低了1.1 K,温差减小了29%。在同等电池组温差下,优化系统的功耗相比优化前系统下降了64%。     

Impact Responses of Prismatic Lithium-Ion Battery Based on the Membrane Factor Method北大核心CSCD

Aimed at the internal short circuit problem due to large deformation of the prismatic lithium-ion battery cell under impact loadings, a simplified battery model was first established. Then the motion equations of velocity and displacement based on the membrane factor method were proposed. With the effects of the face-sheet thickness and the densification region on the normalized final deflection, impact response characteristics of prismatic battery cells were investigated in detail. The results show that, the improved motion equations involving the membrane factor can reflect the dynamic response mechanisms of the prismatic battery cell under impact loadings, and the large deflection under high-speed impact can be predicted. With the increase of the face-sheet thickness, the deflection of the battery cell’s lower part decreases obviously. However, the densification region expands with the face-sheet thickness. The deflection and the densification region of the cell’s lower part both increase with the inner core density of the battery. This proposed impact model provides a theoretical guidance for the multi-functional integrated dynamic design of prismatic battery cells. © 2022 Editorial Office of Applied Mathematics and Mechanics. All rights reserved.     

层状LiMnO2的固相合成及电化学性能

以Mn₂O₃和氢氧化锂为原料，通过焙烧合成出o-LiMnO₂。用X射线衍射和扫描电镜对不同温度下合成的粉末样品进行了表征，并研究了材料的电化学性能。通过对不同温度条件下烧结样品的晶胞参数、布拉格(110)晶面峰半高宽及电化学性能研究发现：600 ℃下合成样品的半高宽最大，堆垛层错率高，同时电化学性能也最好，首次放电容量达到156 mAh·g^-1，20次循环后仍保持在140 mAh·g^-1以上。中高温固相合成的o-LiMnO₂材料，在晶粒范围大小相近时，材料电化学性能与材料堆垛层错率相关。     

锂离子电池负极合金CoSn和Cu-Sn的制备与表征

CoSn alloy and Cu-Sn samples were synthesized by H₂-reduction following solid-state reaction between Co(Ⅱ)， Cu(Ⅱ)， Sn(Ⅳ) and NaOH at ambient temperature. The samples were characterized by XRD， SEM. The results showed that CoSn alloy (80～200nm) is globe-shaped， ultrafine hexagonal material， and Cu-Sn alloy powder consists of two phases， i.e. Cu₆Sn₅ and Cu₃Sn. Cu-Sn powder has spherical morphology and the particle size is estimated to be 60～70nm. The electrochemical performances of CoSn alloy and Cu-Sn powder were studied using lithium-ions model cell Li/LiPF₆ (EC+DMC)/CoSn (or Cu-Sn). It was demonstrated the reversible discharge capacities for 10 cycles keep above 280mAh·g^-1 for nanophase Cu-Sn， and 60mAh·g^-1 for CoSn alloy. Differ-ential capacity plots showed that the reaction mechanisms of Cu-Sn with lithium were reversible.