功能性丙烯酸/MBAM体系共聚产物的研制

以丙烯酸和MBAM为主要原料，经聚合，合成了一种高性能的具有良好保水性能的聚合产物，其保水量达到750～1000倍．50℃以下有良好的保水性能，28℃以下有极好的保水性能，并研究了工艺条件对该产品性能的影响因素．     

Surface polarity of cellulose derivates observed by coumarin 151 and 153 as solvatochromic and fluorochromic probes

Solvent‐dependent ultraviolet–visible (UV–vis) absorption and Stokes shifts including strong hydrogen‐bond‐donating (HBD) solvents such as 2,2,2‐trifluoroethanol and 1,1,1,3,3,3‐hexafluoro‐2‐propanol of two coumarine dyes (Co 151 and Co 153) were analyzed with multiple‐square analyses of linear solvation energy relationships and the Kamlet–Taft solvent parameter set to α (HBD capacity), β (hydrogen‐bond‐accepting capacity), and π* (dipolarity/polarizability). The UV–vis absorption and emission spectra of Co 151 and Co 153 were measured when adsorbed on various polysaccharides such as different cellulose batches, carboxymethylcelluloses with different degrees of substitution, and chitine. As a result of this evaluation, Co 153 is recommended as an alternative UV–vis probe for evaluating the dipolarity/polarizability of cellulose and cellulose derivates. Multiple adsorption of Co 153 on Linters cellulose took place indicating a wide‐surface polarity distribution, which makes the determination of a rigid polarity parameter questionable. Thus, fluorescence measurements of adsorbed Co 153 are suitable to detect inhomogenities on a surface but not for the determination of empirical polarity parameters. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1210–1218, 2003     

Latex particles bearing hydrophilic grafted hairs with controlled chain length and functionality synthesized by reversible addition–fragmentation chain transfer

A method is described for synthesizing latex particles with anchored hairs by the grafting of hydrophilic chains, synthesized by reversible addition–fragmentation chain transfer, onto functionalized latex particles. These have the potential to bind biologically active species. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1188–1195, 2003     

Self‐curable polyester by a reaction of glycidol with maleic anhydride

The controlled reaction of equimolar quantities of maleic anhydride and glycidol in dimethoxyethane gives soluble polyesters with one hydroxyl group in each repeating unit. The reaction proceeds with stepwise ring opening of the components and gives highly viscous clear solutions in relatively short periods. In the first step, monomaleate ester formation takes place around 80 °C. The ring opening of the oxirane group is the second step, and it occurs at 120 °C. The overall reaction is the formation of soluble polyesters with moderate molecular weights (6000–18,000), without the elimination of water. The soluble polyesters can be crosslinked tightly by direct heating at 190 °C without additional vinyl monomer. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2549–2555, 2003     

Dispersion and distribution of organically modified montmorillonite in nylon‐66 matrix

Nylon‐66 nanocomposites were prepared by melt‐compounding nylon‐66 with an alkyl ammonium surfactant pretreated montmorillonite (MMT). The thermal stability of the organic MMT powders was measured by thermogravimetric analysis. The decomposition of the surfactant on the MMT occurred from 200 to 500 °C. The low onset decomposition temperature of the organic MMT is one shortcoming when it is used to prepare polymer nanocomposites at high melt‐compounding temperatures. To provide greater property enhancement and better thermal stability of the polymer/MMT nanocomposites, it is necessary to develop MMT modified with more thermally stable surfactants. The dispersion and spatial distribution of the organic MMT layers in the nylon‐66 matrix were characterized by X‐ray diffraction. The organic MMT layers were exfoliated but not randomly dispersed in the nylon‐66 matrix. A model was proposed to describe the spatial distribution of the organic MMT layers in an injection‐molded rectangular bar of nylon‐66/organic MMT nanocomposites. Most organic MMT layers were oriented in the injection‐molding direction. Layers near the four surfaces of the bar were parallel to their corresponding surfaces; whereas those in the bulk differed from the near‐surface layers and rotated themselves about the injection‐molding direction. The influence of the spatial distribution of the organic MMT on crystallization of nylon‐66 was also investigated. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1234–1243, 2003     

Controlled/living polymerization of 2‐(diethylamino)ethyl methacrylate and its block copolymer with tert‐butyl methacrylate by atom transfer radical polymerization

Polymerization of 2‐(diethylamino)ethyl methacrylate (DEAEMA) via homogeneous atom transfer radical polymerization under various reaction conditions is described. The effects of the initiators and solvents were examined. With 1,1,4,7,10,10‐hexamethyl triethylenetetramine/copper(I) chloride/p‐toluenesulfonyl chloride as the ligand/catalyst/initiator system in methanol, poly(DEAEMA) with a polydispersity index as low as 1.07 was synthesized. Kinetic studies demonstrated the polymerization was very well controlled and exhibited the living characteristic of the process. Well‐defined block copolymers of DEAEMA and tert‐butyl methacrylate (tBMA) were successfully synthesized. The copolymers could be synthesized with equally good results by starting with either p(DEAEMA) or p(tBMA) as the macroinitiators. However, only the macroinitiators terminated with chlorine should be used. The corresponding macroinitiators with bromine as a transferable group did not yield well‐defined copolymers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2688–2695, 2003     

Annealing behavior of gel‐spun polyethylene fibers at temperatures lower than needed for significant shrinkage

The annealing at 373 K of ultrastrong, gel‐spun polyethylene (PE) has been studied. At this temperature, the fibers show no significant shrinkage. Still, a significant decrease in the mechanical properties is observed. The fibers have been analyzed with differential scanning calorimetry (DSC), temperature‐modulated differential scanning calorimetry (TMDSC), atomic force microscopy (AFM), and small‐angle X‐ray scattering (SAXS). During the annealing, the glass transition of the intermediate phase is exceeded, as shown by DSC. When split for structure analysis by AFM, the annealed fibers undergo plastic deformation around the base fibrils instead of brittle fracture. The quasi‐isothermal TMDSC experiments are compared to the minor structural changes seen with SAXS and AFM. The loss of performance of the PE fibers at 373 K is suggested to be caused by the oriented intermediate phase, and not by major changes in the structure or morphology. The overall metastable, semicrystalline structure is shown by TMDSC to posses local regions that can melt reversibly. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 403–417, 2003     

The analysis of volatile trace compounds in landfill gases,compost heaps and forest air

Landfill gas, cryotrapped on a loop fashioned from a length of a capillary gas chromatography (GC) column, was examined for volatile organometallic compounds (VOMCs) and for volatile organic compounds (VOCs) by using GC–mass spectrometry (MS). A large number of organic components were present and many were identified, but the only VOMCs present in high enough concentrations to be detected were trimethylstibine and tetramethyltin. The use of inductively coupled plasma (ICP)‐MS as an element‐specific detector allowed the identification of a number of other organometallic species in the landfill gas, including trimethylarsine and trimethylbismuth, and, for the first time, butyltrimethyltin and dibutyldimethyltin. The presence of molybdenum hexacarbonyl was confirmed. Gas from a large‐scale compost heap and from compost incubated in the laboratory contained iodomethane but no common VOMCs (GC–ICP‐MS). Only VOCs were present in forest air (GC–MS). Copyright © 2003 John Wiley & Sons, Ltd.     

Mass‐lumping or not mass‐lumping for eigenvalue problems

In this article we analyze the effect of mass‐lumping in the linear triangular finite element approximation of second‐order elliptic eigenvalue problems. We prove that the eigenvalue obtained by using mass‐lumping is always below the one obtained with exact integration. For singular eigenfunctions, as those arising in non convex polygons, we prove that the eigenvalue obtained with mass‐lumping is above the exact eigenvalue when the mesh size is small enough. So, we conclude that the use of mass‐lumping is convenient in the singular case. When the eigenfunction is smooth several numerical experiments suggest that the eigenvalue computed with mass‐lumping is below the exact one if the mesh is not too coarse. © 2003 Wiley Periodicals, Inc. Numer Methods Partial Differential Eq 19: 653–664, 2003     

Depth profile analysis of polyimide film treated by potassium hydroxide

The structural change in the depth direction of a polyimide (UPILEX‐S) film treated in alkaline solution, which was a representative surface treatment used to form a seed layer for plating and to improve the adhesive strength, was analyzed by means of micro Fourier transform infrared attenuated total reflection (FTIR‐ATR) line analysis with gradient shaving preparation. The polyimide film was treated with KOH. The imide ring opened through the alkaline treatment, and the amide structure and carboxylic acid salt were formed. The attainment depth of this structural change was almost proportional to the treatment time, and it reached about 8 μm after a 30‐min treatment. The degree of structural change through the alkaline treatment was almost constant after it reached a considerably degraded stage, and the chemically changed region penetrated into the inner part of the film from the surface. An intermediate layer before the final degraded stage appeared in the treated layer, and its thickness increased with the treatment time. The region that was changed chemically by the alkaline treatment progressed to the inner part simultaneously and continuously as the treatment time increased. The combined use of gradient shaving preparation and micro FTIR‐ATR line analysis was found to be extremely effective for the depth profiling of organic materials. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2071–2078, 2003