Raising the bar on-bead: Efficient on-resin synthesis of α-conotoxin LvIA

α4/7-Conotoxin LvIA is an isoform-selective inhibitor of the α3β2 nicotinic acetylcholine receptor. An efficient strategy for the synthesis of this toxin is critical to advancing its utility as a probe for receptor function and as a potential pharmaceutical lead target. On-resin methods for peptide synthesis offer potential synthetic advantages; however, strategies for on-resin formation of multiple disulfides have historically been low-yielding. Here, we harness the reactivity of the Allocam protecting group and employ a 3-amino acid spacer strategy to synthesize α4/7-conotoxin LvIA via three different on-resin strategies, each of which results in an isolated yield higher than previous fully on-resin approaches.     

超支化铬系催化剂的合成及乙烯齐聚性能研究

以不同端基烷基链长度的1.0G超支化大分子为桥联基,通过对其端基氨基进行催化功能改性,合成了系列具有不同桥联基长度的超支化PNP铬系催化剂。采用红外光谱(IR)、核磁共振氢谱(1H-NMR)、核磁共振磷谱(31P-NMR)、紫外光谱(UV)和质谱(MS)等表征方法证明合成催化剂的结构与理论结构相符。详细考察了溶剂种类、反应温度、Al/Cr摩尔比、反应压力、催化剂用量和催化剂结构对催化剂乙烯齐聚性能的影响。实验结果表明,当以甲苯为溶剂,甲基铝氧烷(MAO)为助催化剂时,超支化PNP铬系催化剂表现出良好的催化乙烯齐聚性能,产物以低碳烯烃为主。最佳条件下,催化活性最高可达到1.69×105g/mol Cr·h,己烯和辛烯的选择性为43.3%以上。相同聚合条件下,其催化活性随着端基烷基链长度的增加而下降。     

Chromium complexes based on thiophene–imine ligands for ethylene oligomerization

A new set of Cr(III) complexes, {L}CrCl₃(THF), based on thiophene–imine ( 2a , L = PhOC₆H₄(N═CH)‐2‐SC₄H₃; 2b , L = PhOC₂H₄(N═CH)‐2‐SC₄H₃; 2c , L = Ph(NH)C₂H₄(N═CH)‐2‐SC₄H₃; 2d , L = PhOC₆H₄(N═CH)‐2‐SC₄H₂‐5‐Ph; 2e , L = Ph(NH)C₂H₄(N═CH)‐2‐SC₄H₂‐5‐Ph) have been prepared and characterized using elemental analysis and infrared spectroscopy. Upon activation with methylaluminoxane, all the chromium complexes generated active systems affording a nonselective distribution of α‐olefins with turnover frequencies in the range 9500–93 500 (mol ethylene) (mol Cr)^?1 h^?1, and producing mostly oligomers (95.0–99.3 wt% of total products). Small amounts of polymer were produced in these oligomerization reactions (0.8–8.2 wt%). The catalytic activities were quite sensitive to the ligand environment. Moreover, the effects of oligomerization parameters (temperature, [Al]/[Cr] molar ratio, time) on the activity and on the product distribution were examined.     

Brush‐First ROMP of poly(ethylene oxide) macromonomers of varied length: impact of polymer architecture on thermal behavior and Li+ conductivity

The properties of polymeric materials are dictated not only by their composition but also by their molecular architecture. Here, by employing brush‐first ring‐opening metathesis polymerization (ROMP), norbornene‐terminated poly(ethylene oxide) (PEO) macromonomers ( MM‐n , linear architecture), bottlebrush polymers ( Brush‐n , comb architecture), and brush‐arm star polymers ( BASP‐n , star architecture), where n indicates the average degree of polymerization (DP) of PEO, are synthesized. The impact of architecture on the thermal properties and Li⁺ conductivities for this series of PEO architectures is investigated. Notably, in polymers bearing PEO with the highest degree of polymerization, irrespective of differences in architecture and molecular weight (~100‐fold differences), electrolytes with lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) as an Li⁺ source exhibit normalized ionic conductivities (σ_n) within only 4.9 times difference (σ_n = 29.8 × 10^?5 S cm^?1 for MM‐45 and σ_n = 6.07 × 10^?5 S cm^?1 for BASP‐45 ) at a concentration of Li⁺ r = [Li⁺]/[EO] = 1/12 at 50 °C. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 448–455     

Palladium complexes bearing an N‐heterocyclic carbene–sulfonamide ligand for cooligomerization of ethylene and polar monomers

Herein, we report the synthesis of palladium complexes bearing an N‐heterocyclic carbene (NHC)‐sulfonamide bidentate ligand and their application in ethylene oligomerization and ethylene/polar monomer cooligomerization. These catalysts could smoothly catalyze ethylene oligomerization and ethylene/methyl acrylate cooligomerization albeit the performance was lower compared to that of a NHC–phenoxide catalyst. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 474–477     

无水三氯化铝催化乙醇脱水反应制乙烯的实验研究

针对浓硫酸或五氧化二磷作催化剂的不足,该研究采用无水三氯化铝催化乙醇制乙烯,可使反应体系在120~130℃左右产生大量乙烯气体。同时从理论上探究了无水三氯化铝催化乙醇脱水的机理,并从教学演示实验的角度改进了反应装置,取得了较好的实验效果。     

油浆高温快速裂解过程的气固相产物研究

采用高频炉快速热解装置研究油浆的高温快速热解特性,考察了热解温度、氮气流量对气固相产物的组成和产率的影响。温度是影响气相产物产率的关键因素,气相产物主要为甲烷、氢气和乙烯,升高温度可提高甲烷和氢气的产率,而乙烯产率受高温下二次反应的影响在800℃到达最大值后逐渐降低,乙烷、丙烯产率较小且受二次反应的影响在700℃到达最大值后逐渐降低,温度高于800℃时会有少量乙炔生成且升温可提高乙炔产率。增加氮气流量可降低甲烷、氢气分压,缩短乙烯、丙烯等在高温区的停留时间,从而增加气相产物的产率。积炭产率随热解温度升高迅速增加,氮气流量的增加能够削弱二次反应从而降低积炭产率。     

pH‐Dependent Nitrotyrosine Formation in Ribonuclease A is Enhanced in the Presence of Polyethylene Glycol (PEG)

Protein nitration can occur as a result of peroxynitrite‐mediated oxidative stress. Excess production of peroxynitrite (PN) within the cellular medium can cause oxidative damage to biomolecules. The in vitro nitration of Ribonuclease A (RNase A) results in nitrotyrosine (NT) formation with a strong dependence on the pH of the medium. In order to mimic the cellular environment in this study, PN‐mediated RNase A nitration has been carried out in a crowded medium. The degree of nitration is higher at pH 7.4 (physiological pH) compared to pH 6.0 (tumor cell pH). The extent of nitration increases significantly when PN is added to RNase A in the presence of crowding agents PEG 400 and PEG 6000. PEG has been found to stabilize PN over a prolonged period, thereby increasing the degree of nitration. NT formation in RNase A also results in a significant loss in enzymatic activity.     

Glycidyl Tosylate: Polymerization of a “Non‐Polymerizable” Monomer permits Universal Post‐Functionalization of Polyethers

Glycidyl tosylate appears to be a non‐polymerizable epoxide when nucleophilic initiators are used because of the excellent leaving group properties of the tosylate. However, using the monomer‐activated mechanism, this unusual monomer can be copolymerized with ethylene oxide (EO) and propylene oxide (PO), respectively, yielding copolymers with 7–25 % incorporated tosylate‐moieties. The microstructure of the copolymers was investigated via in situ ¹H NMR spectroscopy, and the reactivity ratios of the copolymerizations have been determined. Quantitative nucleophilic substitution of the tosylate‐moiety is demonstrated for several examples. This new structure provides access to a library of functionalized polyethers that cannot be synthesized by conventional oxyanionic polymerization.     

MAO‐free and extremely active catalytic system for ethylene tetramerization

The original Sasol catalytic system for ethylene tetramerization is composed of a Cr source, a PNP ligand, and MAO (methylaluminoxane). The use of expensive MAO in excess has been a critical concern in commercial operation. Many efforts have been made to replace MAO with non‐coordinating anions (e.g., [B(C₆F₅)₄]^?); however, most of such attempts were unsuccessful. Herein, an extremely active catalytic system that avoids the use of MAO is presented. The successive addition of two equivalent [H(OEt₂)₂]⁺[B(C₆F₅)₄]^? and one equivalent CrCl₃(THF)₃ to (acac)AlEt₂ and subsequent treatment with a PNP ligand [CH₃(CH₂)₁₆]₂C(H)N(PPh₂)₂ ( 1 ) yielded a complex presumably formulated as [ 1 ‐CrAl (acac)Cl₃(THF)]²⁺[B(C₆F₅)₄]^?₂, which exhibited high activity when combined with iBu₃Al (1120 kg/g‐Cr/h; ~4 times that of the original Sasol system composed of Cr (acac)₃, iPrN(PPh₂)₂, and MAO). Via the introduction of bulky trialkylsilyl substituents such as –SiMe₃, –Si(nBu)₃, or –SiMe₂(CH₂)₇CH₃ at the para‐position of phenyl groups in 1 (i.e., by using [CH₃(CH₂)₁₆]₂C(H)N[P(C₆H₄‐p‐SiR₃)₂]₂ instead of 1 ), the activities were dramatically improved, i.e., tripled (2960–3340 kg/g‐Cr/h; more than 10 times that of the original Sasol system). The generation of significantly less PE (<0.2 wt%) even at a high temperature is another advantage achieved by the introduction of bulky trialkylsilyl substituents. NMR studies and DFT calculations suggest that increase of the steric bulkiness on the alkyl‐N and P‐aryl moieties restrict the free rotation around (alkyl)N–P (aryl) bonds, which may cause the generation of more robust active species in higher proportion, leading to extremely high activity along with the generation of a smaller amount of PE.