Development of MEMS-based direct methanol fuel cell with high power density using nanoimprint technology

Performance of MEMS-based DMFC is low, because graphite-based porous electrodes show poor compatibility with MEMS technology. Nanoimprint technology was adopted in this paper to prepare fine pattern on proton exchange membrane (PEM) in MEMS-based DMFC as a promising alternative to the graphite-based porous electrodes. Micro-convex with the diameter of about 600 nm and the height of 50–70 nm was prepared on Nafion^® 117 membrane by the nanoimprint at 130 °C using silicon mold. Thick Pt film (20 nm) was deposited as catalyst directly on the nanoimprinted Nafion^® 117 membrane. Then the Pt-coated PEM was sandwiched with micro-channeled silicon plates to form a micro-DMFC. With passively feeding of 1 M methanol solution and air at room temperature, the as-prepared cell had the open circuit voltage (OCV) of 0.74 V and the maximum power density of 0.20 mW/cm². The measured OCV was higher than those (0.1–0.3 V) of the state-of-the-art MEMS-based DMFC with planar electrode and pure Pt catalyst.     

A cytotoxic compound from the leaves of Juglans mandshurica

From Juglans mandshurica leaves, a new quinone compound was isolated through bioassay-guided fractionation. The structure elucidation of the compound was established based on spectroscopic studies, notably of the 2D NMR spectra. The compound exhibited moderate cytotoxic activities against Hela, MCF-7, BGC823 and 3T3-Llcell lines with IC50 ranges from 7.5 to 26.8 μmol/L.     

Sorption of Co(II) ong-alumina in the presence and absence of fulvic acid</p> </p>

Summary The removal of heavy metal ion Co(II) from aqueous solution was studied usingg-Al₂O₃ by batch technique. The experiments were performed at T=20±2 °C, in 0.01M NaNO₃ solutions and under aerobic conditions. The effect of pH, ionic strength, fulvic acid (FA) and alumina amount on the sorption of Co(II) on alumina were also investigated. The pH affected the sorption of Co(II) significantly as compared with the effect of FA and ionic strength. The results indicated that strong chemical bonds are formed between Co(II) and functional groups of the bare or FA coated alumina, and a precipitation of Co(II) takes place on the alumina surface, induced by a transition from the adsorption to surface. The addition sequences of Co/FA on Co(II) sorption were also studied: the sorption of Co(II) in the ternary system was found independent of addition sequences.</p> </p>     

Preparation of TiO2 nanocrystallites by hydrolyzing with gaseous water and their photocatalytic activity

TiO₂ nanocrystallites were prepared from precursors tetra-n-butyl titanate (Ti(OC₄H₉)₄) and titanium tetrachloride (TiCl₄). The precursors were hydrolyzed by gaseous water in autoclave, and then calcined at predetermined testing temperatures. The samples were characterized by X-ray diffraction (XRD), thermogravimetry–differential thermal analysis (TG–DTA), field emission scanning electron microscopy (FE-SEM), Fourier transform infrared spectra (FT-IR), and UV–vis diffuse reflectance spectra (DRS). The photocatalytic activities of the samples were evaluated by the photobleaching of methylene blue (MB) in aqueous solution and the photocatalytic oxidation of propylene in gas phase at ambient temperature. The results showed that the anatase phase nanocrystalline TiO₂ could be obtained at relatively low temperatures (for precursor Ti(OC₄H₉)₄ at 110 °C and for TiCl₄ at 140 °C, respectively), and that the as prepared samples exhibited high photocatalytic activities to photobleach MB in aqueous solution. As the calcination temperatures increasing, the decolor ratio of MB increased and reached the maximum value of nearly 100% at 600 °C, and then decreased. The photobleaching of MB by all samples followed the pseudo-first-order kinetics with respect to MB concentration. The photodecomposition amount of propylene by TiO₂ nanocrystallites calcined at 600 °C from precursor of Ti(OC₄H₉)₄ is 21.6%, which is approaching to that by Degussa P25 TiO₂ (24.9%).     

Influence of drying method on morphology and properties of asymmetric cellulose hollow fiber membrane

Using a dry/wet spinning process, asymmetric cellulose hollow fiber membranes (CHFM) were prepared from a dope composed of cellulose/N-methylmorpholine-N-oxide/water. The formation mechanism for the finger-like macrovoids at the inner portion of as-spun fibers was explained. Naturally drying and three solvent exchange drying methods were tried to investigate their influence on morphology and properties of CHFM. It was found that the ethanol–hexane exchange drying was an appropriate method to minimize morphology change of the as-spun CHFM, whereas the naturally drying caused the greatest shrinkage of the fibers that made the porous membrane become dense. As a result, CHFM from ethanol–hexane exchange drying performed the highest gas permeation rate but gas permeation of the naturally dried membrane could not be detectable. The resultant CHFM from the ethanol–hexane exchange drying also showed acceptable mechanical properties, thus it was proposed to be an appropriate method for gas separation purpose. The experimental results supported the proposed drying mechanism of CHFM. The free water would evaporate or be replaced by a solvent that subsequently would evaporate but the bonded water would remain in the membrane. What dominated the changes of membrane morphology during drying should be the molecular affinities of cellulose–water, water–solvent and solvent–solvent.     

A novel zirconocene/ultradispersed diamond black powder supported catalytic system for ethylene polymerization

A novel carrier of ultradispersed diamond black powder (UDDBP) was used to support metallocene catalyst. Al₂O₃ was also used as carrier in order to compare with UDDBP. Supported catalysts for ethylene polymerization were synthesized by two different reaction methods. One way was direct immobilization of the metallocene on the support, the other was adsorption of MAO onto the support followed by addition of the metallocene. Four supported catalysts Cp₂ZrCl₂/UDDBP, Cp₂ZrCl₂/Al₂O₃, Cp₂ZrCl₂/MAO/UDDBP and Cp₂ZrCl₂/Al₂O₃/MAO were obtained. The content of the zirconium in the supported catalyst was determined by UV spectroscopy. The activity of the ethylene polymerization catalyzed by supported catalyst was investigated. The influence of Al/Zr molar ratio and polymerization temperature on the activity was discussed. The polymerization rate was also observed.     

Determination of Cr(VI) in plants by electrothermal atomic absorption spectrometry after leaching with sodium carbonate

The determination of chromium (VI) compounds in plants by electrothermal atomic absorption spectrometry (ET AAS) is proposed based on their leaching with 0.1 M Na₂CO₃. Due to the presence of relatively high amounts of Na₂CO₃ in the resulting samples, the temperature and time of pyrolysis and atomization stages must be optimized to minimize the influence of the matrix. A limit of detection (LOD) for determination of Cr(VI) in plants by ET AAS was found to be 0.024 μg g⁻¹.The concentration of Cr(VI) and total chromium in plants collected in different geographical areas (South Africa and Russia), grown on soils high in chromium was determined. The concentration of Cr(VI) and total Cr in stems and leaves of plants was in the range of 0.04–0.7 μg g⁻¹ and 0.5–10 μg g⁻¹, respectively. The limited uptake of Cr(III) by plants, in comparison to its concentration in soil, can be explained by the very low solubility of natural Cr(III) compounds.Results for the determination of Cr(VI) were confirmed by the analysis of BCR CRM 545 (Cr(VI) in welding dust) with good agreement between certified (39.5 ± 1.3 μg mg⁻¹) and found (38.8 ± 1.2 μg mg⁻¹) values. The total concentration of Cr in plants has also been determined by ET AAS after dry ashing of samples at 650 °C. Results were confirmed by the analysis of BCR CRM 281 (Trace elements in Rye Grass) with good agreement between the found (2.12 ± 0.16 μg g⁻¹) and certified value (2.14 ± 0.12 μg g⁻¹).     

Subsolidus phase relations and crystal structure of compounds in the PrOx-CaO-CuO system

The subsolidus phase relations of the PrO_x-CaO-CuO pseudo-ternary system sintered at 950-1000°C have been investigated by X-ray powder diffraction. In this system, there exist one compound Ca₁₀Pr₄Cu₂₄O₄₁, one Ca₂Pr₂Cu₅O₁₀-based solid solution, seven three-phase regions and two two-phase regions. The crystal structures of Ca₁₀Pr₄Cu₂₄O₄₁ and Ca₂Pr₂Cu₅O₁₀-based solid solution have been determined. Compound Ca₁₀Pr₄Cu₂₄O₄₁ crystallizes in an orthorhombic cell with space group D_2h²⁰−Cccm, Z=4. Its lattice parameters are a=11.278(2) Å, b=12.448(3) Å and c=27.486(8) Å. The crystal structure of Ca₂Pr₂Cu₅O₁₀-based solid solution is an incommensurate phase based on the orthorhombic NaCuO₂ type subcell. The lattice parameters of the subcell of the Ca_2.4Pr_1.6Cu₅O₁₀ are a₀=2.8246(7) Å, b₀=6.3693(5) Å, c₀=10.679(1) Å, and those of the orthorhombic superstructure are with a=5a₀, b=b₀, c=5c₀. The Ca_2.4Pr_1.6Cu₅O₁₀ structure can also be determined by using a monoclinic supercell with space group C_2h⁵−P2₁/c, Z=4, a=5a₀, b=b₀, and β=104.79(1)° or 136.60(1)°, V=5a₀b₀c₀.     

The first asymmetric addition of organogallium to aldehydes catalyzed by chiral titanium catalysts

The addition of organogallium to aldehydes was realized with titanium tetrachloride as a Lewis acid catalyst. For the first time, the catalytic asymmetric addition of organogallium to aldehydes was investigated with chiral titanium complexes, which were formed from titanium tetrachloride and salan ligands, with mediocre to good chemical yields and enantioselectivities.     

Tuning the Hybridization of Local Exciton and Charge-Transfer States in Highly Efficient Organic Photovoltaic Cells

Decreasing the energy loss is one of the most feasible ways to improve the efficiencies of organic photovoltaic (OPV) cells. Recent studies have suggested that non-radiative energy loss ( ) is the dominant factor that hinders further improvements in state-of-the-art OPV cells. However, there is no rational molecular design strategy for OPV materials with suppressed . Herein, taking molecular surface electrostatic potential (ESP) as a quantitative parameter, we establish a general relationship between chemical structure and intermolecular interactions. The results reveal that increasing the ESP difference between donor and acceptor will enhance the intermolecular interaction. In the OPV cells, the enhanced intermolecular interaction will increase the charge-transfer (CT) state ratio in its hybridization with the local exciton state to facilitate charge generation, but simultaneously result in a larger . These results suggest that finely tuning the ESP of OPV materials is a feasible method to further improve the efficiencies of OPV cells.