基于遗传算法和指标满意度求解的第三方物流企业物流中心选址方法

本利用AHP和模糊综合评价法评价物流中心选址的定性指标、用量化选址模型结合遗传算法计算定量指标，再藉助指标满意度求解把定性和定量的指标进行综合，从而为决策对物流中心选址做出科学的决策提供支持。     

固态金属中声子热传递的分子动力学模拟研究

固态金属中的热传递是声子和自由电子共同作用的结果。自由电子引起的热导率可以通过电导率,利用Wiedemann-Franz定律得到,声子引起的热导率目前仍然不能进行实验测量,只能借助其他方法来研究。本文采用非平衡分子动力学(NEMD)方法,用镶嵌原子方法(EAM)势能模型,模拟计算了不同厚度(1.760-10.56nm)金属镍薄膜中由于声子-声子作用引起的热导率。然后根据纳米厚度金属薄膜的热导率借助关联式推到宏观尺度下由于声子-声子作用引起的热导率。结果表明,对于纳米厚度金属薄膜,由于声子-声子作用引起的热导率比块体金属镍的热导率小一个数量级;薄膜厚度越小,声子-声子作用引起的热导率越小;对于块体金属镍,由于声子-声子作用引起的热导率约占其总热导率的33.0%左右。     

Low Cost, High Efficiency, Gain Flattened L Band EDFA Using FBGs as C Band Seed Generators

A low cost, coolerless 980nm diode pumped, gain flattened L band EDFA with fast transient control, high pump efficiency and gain clamping effect was realized by using FBGs as C band seed generators.     

磁电垒结构中自旋极化输运性质的研究

研究了电子隧穿几类磁电垒结构的自旋极化输运性质，导出统一的传输概率公式，揭示了非 均匀磁场的分布与自旋过滤的关系，同时表明采用有效朗德因子较大的半导体材料可以显著 增强磁电垒结构的自旋过滤效果. 关键词： 磁电垒 自旋过滤 自旋电子学 自旋极化     

CNx纳米管的制备、结构观察及低场致电子发射性能研究

采用高温热解法，以乙二胺为前驱液，在沉积有铁催化剂的p型硅（111）基底上制备出了定向生长的CNx纳米管.利用扫描电子显微镜、高分辨率透射电子显微镜和拉曼光谱对CNx纳米管进行了形貌观察和表征.CNx纳米管的高度在20?μm左右，直径在50—100nm之间，具有明显的“竹节状”结构，结晶有序度较差.对CNx纳米管薄膜进行低场致发射性能测试：外加电场为1.4V/μm，观察到20?μA /cm2发射电流，外电场升至2.54V/μm时发射电流达到1.280mA/cm2，在较高外电场下，没有发现电流“饱和”.这比 关键词： CNx纳米管 高温热解 “竹节状”结构 场致发射     

Proteins Entrapped in Silica Monoliths Prepared from Glyceroxysilanes

The preparation of discrete polyol based silane precursors derived from glycerol by a simple one-pot process is described. These polyol-based silanes could be hydrolyzed under mild pH conditions and upon gelation resulted in the formation of optically clear, monolithic, mesoporous silica. The hydrolysis and condensation reactions lead to cure rates that are very sensitive to ionic strength, but are almost unaffected by pH in contrast to those of alkoxysilanes derived from primary alcohols such as Si(OEt)₄. Residual glycerol in the silica monolith could be removed by washing, or could be left in the silica to reduce the magnitude of shrinkage during long term storage. The biocompatible glyceroxysilane precursors lead to materials that were able to retain the activity of entrapped enzymes over repeated cycles of use for periods of up to several months.     

Exploitation of introducing of catalytic centers into layer galleries of layered silicates and related epoxy nanocomposites. I. Epoxy nanocomposites derived from montmorillonite modified with catalytic surfactant‐bearing carboxyl groups

Montmorillonite (MMT) was modified with the acidified cocamidopropyl betaine (CAB) and the resulting organo‐montmorillonite (O‐MMT) was dispersed in an epoxy/methyl tetrahydrophthalic anhydride system to form epoxy nanocomposites. The intercalation and exfoliation behavior of the epoxy nanocomposites were examined by X‐ray diffraction and transmission electron microscopy. The curing behavior and thermal property were investigated by in situ Fourier transform infrared spectroscopy and DSC, respectively. The results showed that MMT could be highly intercalated by acidified CAB, and O‐MMT could be easily dispersed in epoxy resin to form intercalated/exfoliated epoxy nanocomposites. When the O‐MMT loading was lower than 8 phr (relative to 100 phr resin), exfoliated nanocomposites were achieved. The glass‐transition temperatures (T_g's) of the exfoliated nanocomposite were 20 °C higher than that of the neat resin. At higher O‐MMT loading, partial exfoliation was achieved, and those samples possessed moderately higher T_g's as compared with the neat resin. O‐MMT showed an obviously catalytic nature toward the curing of epoxy resin. The curing rate of the epoxy compound increased with O‐MMT loading. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1192–1198, 2004     

Differential pulse anodic stripping voltammetric determination of traces of copper with a tobramycin-Nafion modified electrode.

A Nafion-modified glassy carbon electrode incorporated with tobramycin for the voltammetric stripping determination of Cu2+ has been explored. The electrode was fabricated by tobramycin containing Nafion on the glassy carbon electrode surface. The modified electrode exhibited a significantly increased sensitivity and selectivity for Cu2+ compared with a bare glassy carbon electrode and the Nafion modified electrode. Cu2+ was accumulated in HAc-NaAc buffer (pH 4.6) at a potential of -0.6 V (vs. SCE) for 300 s and then determined by differential pulse anodic stripping voltammetry. The effects of various parameters, such as the mass of Nafion, the concentration of tobramycin, the pH of the medium, the accumulation potential, the accumulation time and the scan rate, were investigated. Under the optimum conditions, a linear calibration graph was obtained in the concentration range of 1.0 x 10(-9) to 5.0 x 10(-7) mol l(-1) with a correlation coefficient of 0.9971. The relative standard deviations for eight successive determinations were 4.3 and 2.9% for 1.0 x 10(-8) and 2.0 x 10(-7) mol l(-1) Cu2+, respectively. The detection limit (three times signal to noise) was 5.0 x 10(-10) mol l(-1). A study of interfering substances was also performed, and the method was applied to the direct determination of copper in water samples, and also in analytical reagent-grade salts with satisfactory results.     

基于图像处理技术的束流剖面监视系统

 介绍了在兰州重离子加速器上利用荧光靶图像获取装置测量并计算束流剖面参数的方法，并建立了图像获取、处理、束流参数计算的实时测量软件系统。该系统具有可靠性好、测量直观、界面友好等优点。     

Φ520mmF/1.6椭球面反射镜加工

介绍了一块Φ520mm大相对孔径(F/1.6)轻量化椭球面反射镜的加工与检测方法。镜面的有效口径为Φ502mm,顶点曲率半径为1600mm,非球面系数k=-0.9663,面形精度要求优于0.025λ(RMS)。镜子背面有54个大小深浅不一的不通孔,用于减轻镜子的重量。采用WYKO干涉仪检测得到镜面面形误差达RMS0.02λ,λ=632.8nm。