Facile synthesis of exfoliated and highly conductive poly(arylene disulfide)/graphite nanocomposites

Exfoliated graphite has been synthesized by first synthesizing H₂SO₄ intercalated compound in a H₂O₂‐H₂SO₄ mixture, followed by exfoliation under microwave irradiation. Poly(arylene disulfide)/graphite nanocomposites were then fabricated by absorbing cyclic(arylene disulfide) oligomers into the pores of exfoliated graphite. Subsequently, the nanocomposite precursor was subjected to heat treatment to carry out the in situ ring‐opening polymerization of the oligomers via free radical mechanism. The as‐prepared nanocomposite exhibited a exfoliated nanostructure as evidenced by transmission electron microscopy (TEM) observation. The nanocomposite with a very small amount of graphite, 5 wt%, possesses a highly electrical conductivity of 4 S/cm, therefore, many applications can be found as conductive materials. Copyright © 2004 John Wiley & Sons, Ltd.     

Photopolymerization induced by a benzophenone derivative photoinitiator

A benzophenone derivative photoinitiator, HBP-TDI-HQ-TDI-HBP （HTCTH）, was synthesized based on 4-hydroxy benzophenone （HBP）, toluene-2,4-diisocyanate （TDI） and hydroquinone （HQ）. HTCTH was a more effective photoinitiator which had longer wavelength absorption in the UV-vis absorption spectra than the low molecular counterpart benzophenone （BP）. It showed that both rate of polymerization （Rp） and final conversion （P） increased with increase of amine and HTCTH concentration in photopolymerization.     

3-(Triethoxysilyl)propionitrile sol-gel coating

3-(Triethoxysilyl)propionitrile (TESPN) sol-gel has been prepared under different conditions. It was employed for coating the surfaces of quartz and aluminum. Infrared (IR) and Raman spectra of TESPN and TESPN sol-gels have been recorded in the study of the sol-gel process. Transmission and reflection absorption IR (RAIR) spectra of TESPN sol-gel coated quartz and aluminum have also been collected for better understanding the film formation on the substrate surfaces. Spectra collected at different temperatures indicated that the silane film on quartz decomposes at 700 degrees C. Results from thermal gravimetric analysis (TGA) supported this result. Based on the group frequencies and the spectral behavior in different states, some vibrational modes were assigned to the observed bands. The anticorrosion behavior of the sol-gel coated aluminum in comparison with the uncoated metal was evaluated by measuring the potentiodynamic polarization and electrochemical impedance spectra (EIS).     

论测量不确定度

讨论了测量不确定度的基本概念及应用。分析了误差和不确定度两个概念的区别，探讨了不确定度及分量的评定方法。     

Preparation and characterization of nitrogen-doped TiO2 photocatalyst in different acid environments

Nitrogen-doped TiO₂ powders were successfully prepared by a wet method, i.e., a micro-emulsion-hydrothermal method, in different acid environments. Several characterization techniques, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and UV-visible diffuse reflectance spectra, were combined to determine the crystal phase, concentration and chemical states of the nitrogen doped in TiO₂. The high photocatalytic activity of the nitrogen-doped TiO₂ was evaluated through the decomposition of rhodanmine B under visible light irradiation. It was suggested that the doped nitrogen formed oxynitride (NO) and produced impurity states at higher above the valence band of TiO₂. Therefore, the nitrogen doping could enhance the response of photocatalyst to the visible light and improve the photocatalytic activity because of the narrowing of band gap of TiO₂.     

Separation of salidroside from Rhodiola crenulata by high-speed counter-current chromatography

High-speed counter-current chromatography (HSCCC) was used to purify salidroside from an extract of Rhodiola crenulata with two steps using a two-phase solvent system composed of ethyl acetate-n-butanol-water (1:4:5, v/v) in the first run and chloroform-methanol-isopropanol-water (5:6:1:4) in the second run. The method yielded 21.9 mg of salidroside from 1.216 g of the crude sample at 98% purity determined by HPLC analyses. Identification was performed by 1H NMR, 13C NMR, and MS.     

环己硅烷类液晶化合物的量子化学研究

运用AM1和PM3两种SCF-MO方法，通过能量梯度全优化计算，给出20种环己硅烷类（苯基乙烷系）液晶化合物的稳定几何构型、电子结构和基本性质．联系有机电子结构理论进行了细致的讨论．     

从蓖麻油制取10-羟基癸酸的研究

本文报道了从蓖麻油制取10-羟基癸酸的研究,发现了从蓖麻油制取10-羟基癸酸的新的工艺路线和最佳的工艺条件,用氢氧化钠用量、2-辛醇量、反应时间和反应温度四因子三水平L_9(3~4)进行了正交试验,发现最佳工艺条件是:氢氧化钠(g)/蓖麻油(g):1.25:2-辛醇量(g)/蓖麻油(g):2:反应时间:6h;反应温度:180℃。在这一新的工艺路线和最佳工艺条件下,10-羟基癸酸产率可达75％。