多结超导环在外磁场中的行为

分析和计算了双结超导环在无偏置电流时的磁通、环流、自由能与外磁场的关系.发现双结环与单结环在磁场中的行为有所不同.当两个结的Ic相等时，双结环在1＜β=2πLIcΦ0＜2时，若无偏置电流，总磁通Φ、环流I与外磁通Φe的关系仍然是非回滞的曲线.仅当β≥2时，曲线才出现回滞.另外双结环有两支解，并且每支解的周期为2Φ0. 关键词： 双结环 双支解 2Φ0周期 回滞     

In-Situ Intrinsic Interface Strength Measurement at Elevated Temperatures and its Relationship to Interfacial Structure

A previously developed laser spallation technique has been modified to measure the tensile strength of thin film interfaces in-situ at temperatures up to 1100°C. Tensile strengths of Nb/A-plane sapphire, FeCrAl/A-plane sapphire and FeCrAlY/A-plane sapphire were measured up to 950°C. The measured strengths at high temperatures were substantially lower compared with their corresponding strengths at ambient temperature. For example, at 850°C, the interface tensile strength for the Nb/sapphire (151 ± 17 MPa), FeCrAl/sapphire (62 ± 8 MPa) and FeCrAlY/sapphire (82 ± 11 MPa) interface systems were lower by factors of approximately, 3, 5, and 8, respectively, over their corresponding ambient values. These results underscore the importance of using such in-situ measured values under operating conditions as the failure criterion in any life prediction or reliability models of such coated systems where local interface temperature excursions are expected. The results on alloy film interfaces also demonstrate that the presence of Y increases the strength of FeCrAl/Al₂O₃ interfaces.     

70K温区混合工质分凝分离循环节流制冷机实验研究

混合工质节流制冷机正在许多方面获得越来越广泛的应用。文中设计了一种新型的混合工质分凝分离循环 ,建立了实验系统 ,并在 70 K温区进行了实验。实验结果表明 ,节流制冷机可以达到 6 5 .3K的低温 ,并在 72 K温度提供 1W的制冷量 ,输入功率为 5 0 0 W。     

Study on the Binding Characteristic of S-Naproxen Imprinted Polymer and the Interactions between Templates and Monomers

S-naproxen imprinted polymer was prepared with acrylamide as a functional monomer, 1,4-butanediyl diacrylate as a new kind of crossliner, and 2,4,6-trimethylbenzoylphenyl-phosphinic acid ethyl ester as photoinitiator. Their UV and IR spectra were applied to study the interactions between the template and the monomer. Binding experiments showed that the S-naproxen imprinted polymer had better recognition capability for the template than that of a blank polymer. The adsorption distribution coefficient KD of S-naproxen on molecularly-imprinted polymer was 153.2 g/mL, and the separation factor was 1.95 when the initial concentration of substrate was 2.0 mmol/L. Scatchard curves suggested that there were two classes of binding sites in the imprinted polymer and only one class in the blank polymer. Computer simulation using Hyperchem showed the existence of the interactions between the template and the functional monomer as well as the models of the complexes formed by the template and the monomer.     

Giant Magneto-Impedance of Co50Ni22Ga28 Alloy with High Chemical Ordering

The microstructure of CosoNi22Ga28 ribbon with the L10 structure is examined. The band-like morphology is observed. These bands with the width in a range of 40-200 nm appear along the transverse direction of the ribbon. The giant magnetoimpedance （GMI） effect in this alloy is measured. The results show that Co5oNi22Ga28 exhibits a sharp peak of the GAI effect. The maximum GAH ratio up to 360% is detected. The GMI effect measured versus temperature shows large jumps of the magnetoimpedance amplitude at the reversal martensitic transformation temperature 240℃ and Curie temperature 375℃C respectively. The jump ratios of the magnetoimpedance amplitude examined at these temperatures are about 5 and 10, respectively.     

Experimental investigation and theoretical modeling of liquid entrainment in a horizontal tee with a vertical-up branch

This article describes a comprehensive literature review of liquid entrainment in horizontal pipes with vertical-up branches. Deficiencies in the available data and correlations were identified. The Air–water Test Loop for Advanced Thermal–hydraulic Studies (ATLATS) was constructed and entrainment onset and steady-state data were collected for a wide range of flow conditions. Using new insights gained from experimental testing, the authors developed a model for predicting the onset of entrainment and steady-state entrainment rate. Previously published correlations, along with the new model, are compared against all available data. The new model shows very good agreement with the onset data, but is not very good at predicting branch quality at high liquid flow rates.     

Photorefractive Four-Wave Mixing Switches Utilizing Pockels Effect -Longitudinal and Lateral Switches-

We carried out detailed calculations for photorefractive wave-mixing switches based on one of three crystals with high electro-optic coefficients, namely, BaTiO₃, Strontium Barium Niobate (SBN (0.75)), and Potasium Sodium Strontium Barium Niobate (KNSBN). A comparison of results for the three crystals shows that a 0_-cut BaTiO³ crystal is suitable for a longitudinal switch and requires a voltage of about 80 for a 2-mm-thick crystal to induce sufficient phase mismatch. The electrodes must be transparent for the incident and diffracted beams. A 45_-cut SBN (0.75) crystal, however, is suitable for a lateral switch and requires a voltage of about 150 for a 1-mm-wide crystal. The electrodes do not need to be transparent.     

Living polymerization of styrene initiated by mercaptan/ε‐caprolactam

The bulk polymerization of styrene initiated by ?‐caprolactam (CL) and n‐dodecyl mercaptan (RSH) has been explored. This novel polymerization system shows living characteristics. For example, the molecular weight of the resulting polymers increases with conversion, and the system has the ability to form diblock copolymers and so forth. The polymer chain end contains thiol and lactam structures, which we have investigated with Fourier transform infrared, ¹H NMR, and ¹³C NMR techniques. Electron spin resonance spectra and theoretical calculations by the Hartree–Fock methods have been used to examine the mechanism. The results reveal that the initial polymerization starts from thiol via a chain‐transfer reaction, and the propagation proceeds by the insertion of a monomer between the terminal group and the intermediate structure of lactam. Finally, the polymerization kinetics have been examined. The polymerization rate varies linearly with the concentration of CL and RSH, and this confirms the mechanism. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4976–4993, 2004     

Novel,organosoluble, light‐colored fluorinated polyimides based on 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)biphenyl or 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)‐1,1′‐binaphthyl

Two series of fluorinated polyimides were prepared from 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)biphenyl ( 2 ) and 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)‐1,1′‐binaphthyl ( 4 ) with various aromatic dianhydrides via a conventional, two‐step procedure that included a ring‐opening polyaddition to give poly(amic acid)s, followed by chemical or thermal cyclodehydration. The inherent viscosities of the polyimides ranged from 0.54 to 0.73 and 0.19 to 0.36 dL/g, respectively. All the fluorinated polyimides were soluble in many polar organic solvents, such as N,N‐dimethylacetamide and N‐methylpyrrolidone, and afforded transparent and light‐colored films via solution‐casting. These polyimides showed glass‐transition temperatures in the ranges of 222–280 and 257–351 °C by DSC, softening temperatures in the range of 264–301 °C by thermomechanical analysis, and a decomposition temperature for 10% weight loss above 520 °C both in nitrogen and air atmospheres. The polyimides had low moisture absorptions of 0.23–0.58%, low dielectric constants of 2.84–3.61 at 10 kHz, and an ultraviolet–visible absorption cutoff wavelength at 351–434 nm. Copolyimides derived from the same dianhydrides with an equimolar mixture of 4,4′‐oxydianiline and diamine 2 or 4 were also prepared and characterized. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2416–2431, 2004     

Combined effects of clay modifications and compatibilizers on the formation and physical properties of melt‐mixed polypropylene/clay nanocomposites

The melt mixing technique was used to prepare various polypropylene (PP)‐based (nano)composites. Two commercial organoclays (denoted 20A and 30B) served as the fillers for the PP matrix, and two different maleated (so‐called) compatibilizers (denoted PP‐MA and SMA) were employed as the third component. The results from X‐ray diffraction (XRD) and transmission electron microscope (TEM) experiments revealed that 190 °C was an adequate temperature for preparing the nanocomposites. Nanocomposites were achieved only if specific pairs of organoclay and compatibilizer were simultaneously incorporated in the PP matrix. For example, PP/20A(5 wt %)/PP‐MA(10 wt %) and PP/30B(5 wt %)/SMA(5 wt %) composites exhibited nanoscaled dispersion of 20A or 30B in the PP matrix. Differential scanning calorimetry (DSC) results indicated that the organoclays served as nucleation agents for the PP matrix. Generally, their nucleation effectiveness increased with the addition of compatibilizers. The thermal stability enhancement of PP after adding 20A was confirmed with thermogravimetric analysis (TGA). The enhancement became more evident as a suitable compatibilizer was further added. However, for the 30B‐included composites, thermal stability enhancement was not evident. The dynamic mechanical properties (i.e., storage modulus and loss modulus) of PP increased as the nanocomposites were formed; the properties increment corresponded to the organoclay dispersion status in the matrix. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4139–4150, 2004