Recent developments in the chemistry of stable doubly bonded germanium compounds

During the last 10 years, several compounds of the type Ge=X (X = C, Ge, N, P, S) have been isolated as monomers. The stabilization of such derivatives, which are generally highly polymerizable, was achieved by using very bulky groups both on the germanium atom and on the heteroelement X. Conjugation (particularly in a few germenes and germaimines) and intramolecular or intermolecular coordination with oxygen or nitrogen, also contributes, in some cases, to the stabilization. The X-ray analyses of such compounds show a significant bond shortening of the double bond (8–10%) relative to the corresponding single bond and a planar or nearly planar germanium. These doubly bonded germanium derivatives are usually thermally stable but must be handled in an inert atmosphere because of their high sensitivity to oxygen and moisture; they are extremely reactive, much more than the corresponding carbon analogues. Nearly quantitative additions on the double bond have been observed with electrophiles and nucleophiles, and various types of cycloadditions also occur. Except in one case, a germylene behavior has not been observed, proving that such compounds retain their structural integrity in solution.     

Mechanical properties of polyester polymer-concrete

The properties of a polymer-concrete composed of polyester matrix and locally available rock aggregate are investigated. The formula of the concrete is found by an experimental-calculation approach in such a way as to attain a closer packing of the aggregate particles on the one hand, and to ensure the needed processing characteristics (placeability) of the mix on the other. It is shown experimentally that the material obtained has a rather high compression strength. Under prolonged compression loads, the polymer-concrete exhibits a noticeable creep behavior with a linear relation between the creep strains and stresses. After the action of half the ultimate load over 3000 h, the total strains exceed the instantaneous ones by 2.0 to 2.2 times. The accumulation of irreversible strains is also observed; however, their contribution to the total strain is small. It is found that the stress-strain relation can be represented by the equation of linear hereditary creep theory.Institute of Polymer Mechanics, University of Latvia, Riga, LV-1006, Latvia. Translated from Mekhanika Kompozitnykh Materialov, Vol. 35, No. 2, pp. 147–162, March–April, 1999.     

Three-dimensional atom probe study of the segregation behaviour of Ni91Pt9 alloy after sputtering

To investigate local ordering and segregation phenomenon in a Ni91Pt9-alloy after sputtering and annealing a 3D optical atom probe (OAP) has been used. The specimen tips have been prepared from polycrystalline samples. To sputter the samples a separate preparation chamber with a scannable Ar-sputter-gun is connected to the OAP vessel. When necessary, the sample can be electrically heated to induce segregation and cure the altered layer. After a heat treatment of a Ni91 at. %Pt 9 at.% specimen at 1100 K the surface of a (111)-oriented specimen is enriched in platinum by a factor of two in relation to the bulk. The phenomenon of short-range ordering has been investigated on the surface and in the subsurface volume. A 3D reconstruction of this annealed NiPt specimen shows regions with high concentration of platinum that gives an indication at short-range ordering. Uniform sputtering of the tip without a heat treatment induces a decisive depletion of Pt on the surface and the following subatomic layers. The atom-probe results of specimens in thermal equilibrium are in close agreement to further surface sensitive results obtained from Ion Scattering Spectroscopy (ISS) and Auger Electron Spectroscopy (AES).     

Improved spacer design and cost reduction in an electrodialysis system

In electrodialysis using thin membranes and spacers, the compactness of the membrane cell-pairs leads to a small potential drop, and hence to energy saving. The spacer design itself has a great effect on the cost of the plants, since spacers act as turbulence promoters. A careful design, to increase the mass transfer coefficients, can reduce the membrane surface area required for a given application. Limiting current measurements, cell-pair resistance and pressure losses are presented for several thin spacers, for different flow-velocity values and feed water concentrations. It was possible to find an advantageous geometry of the separating mesh leading to substantial savings on investment and operation costs.     

The lead tetraacetate oxidation of bisacylhydrazones of α-diketones: A scope re-assesment

Oxidation of the title compounds yields, besides the reported isoimides 3 and/or the amides 4 , also the imides 5 . The observed product dichotomy is considered as the result of an intramolecular nucleophilic attack on the aroyl group, of the pressumed zwitterionic intermediate 2 , by O or N present in the ambident N-aroylimine site of 2 . The results of AM1 calculations agree with the product studies and both permit the formulation of a set of rules correlating structure and selectivity.     

Estimation of multivariate binary density using orthogonal functions

In this paper, the authors studied certain properties of the estimate of Liang and Krishnaiah (1985, J. Multivariate Anal. 16, 162–172) for multivariate binary density. An alternative shrinkage estimate is also obtained. The above results are generalized to general orthonormal systems.     

A New Distribution Function for Risk Analysis

This paper presents an alternative to the beta continuous probability distribution for risk analysis. Particular attention has been given to two major applications of distributions, namely project management risk and critical path analysis (PERT). In conjunction with the beta, the triangular and normal distributions are frequently employed in order to give sufficient robustness to risk analysis. The beta distribution, as used in PERT, has a major theoretical implementation flaw. The new distribution was developed to give a possible alternative method of assessing risk. It is shown that the requirement to estimate the most pessimistic variate may be replaced by the probability to exceed the mode. Proposals for other simplifications in risk analysis are discussed. Practical means to validate the most appropriate distributions for risk analysis are outlined, and a cost-data case study is included.