Green synthesis of hydrotalcite from untreated magnesium oxide and aluminum hydroxide

The influence of reaction temperature and time on the hydrothermal dissolution-precipitation synthesis of hydrotalcite was investigated. Untreated MgO, Al(OH)₃ and NaHCO₃ were used. An industrially beneficial, economically favourable, environmentally friendly, zero effluent synthesis procedure was devised based on green chemistry principles, in which the salt-rich effluent typically produced was eliminated by regenerating the sodium bicarbonate in a full recycle process. It was found that the formation of hydromagnesite dominates at low temperatures independent of reaction time. With an increase in reaction time and temperature, hydromagnesite decomposes to form magnesite. At low temperatures, the formation of hydrotalcite is limited by the solubility of the Al(OH)₃. To achieve a hydrotalcite yield of 96%, a reaction temperature of 160°C for 5?h is required. A yield higher than 99% was achieved at 180°C and 5?h reaction time, producing an layered double hydroxide with high crystallinity and homogeneity.     

Surface effects and electrochemical cell capacitance in desorption electrospray ionization

Time resolved measurements show that during a desorption electrospray ionization (DESI) experiment, the current initially rises sharply, followed by an exponential decrease to a relatively steady current. When the high voltage on the spray emitter is switched off, the current drops to negative values, suggesting that the direction of current flow in the equivalent DESI circuit is reversed. These data demonstrate that the DESI source behaves as a dc capacitor and that the addition of a surface between the sprayer and the counter electrode in DESI introduces a new electrically active element into the system. The charging and discharging behavior was observed using different surfaces and it could be seen both by making current measurements on a plate at the entrance to the mass spectrometer as well as by measuring ion current in the linear ion trap within the vacuum system of the mass spectrometer. The magnitude of the steady state current obtained without analyte present on the surface is different for different surface materials, and different capacitor time constants of the equivalent RC circuits were calculated for different DESI surfaces. The PTFE surface has by far the greatest time constant and is also able to produce the highest DESI currents. Surface properties play a crucial role in charge transfer during DESI in addition to the effects of the chemical properties of the analyte. It is suggested that surface energy (wettability) is an important factor controlling droplet behavior on the surface. The experimental data are correlated with critical surface tension values of different materials. It is proposed, based on the results presented, that super-hydrophobic materials with extremely high contact angles have the potential to be excellent DESI substrates. It is also demonstrated, using the example of the neurotransmitter dopamine, that the surface charge that develops during a DESI-MS experiment can cause electrochemical oxidation of the analyte.     

Precise mass measurement of a double-stranded 500 base-pair (309 kDa) polymerase chain reaction product by negative ion electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry

Electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry (ESI-FTICRMS) has been used to determine the mass of a double-stranded 500 base-pair (bp) polymerase chain reaction (PCR) product with an average theoretical mass of the blunt-ended (i.e. unadenylated) species of 308 859.35 Da. The PCR product was generated from the linearized bacteriophage Lambda genome which is a double-stranded template. Utilization of ethanol precipitation in tandem with a rapid microdialysis step to purify and desalt the PCR product was crucial to obtain a precise mass measurement. The PCR product (0.8 pmol/μL) was electrosprayed from a solution containing 75% acetonitrile, 25 mM piperidine, and 25 mM imidazole and was infused at a rate of 200 nL/min. The average molecular mass and the corresponding precision were determined using the charge-states ranging from 172 to 235 net negative charges. The experimental mass and corresponding precision (reported as the 95% confidence interval of the mean) was 309 406 +/- 27 Da (87 ppm). The mass accuracy was compromised due to the fact that the PCR generates multiple products when using Taq polymerase due to the non-template directed 3'-adenylation. This results in a mixture of three PCR products with nearly identical mass (i.e. blunt-ended, mono-adenylated and di-adenylated) with unknown relative abundances that were not resolved in the spectrum. Thus, the experimental mass will be a weighted average of the three species which, under our experimental conditions, reflects a nearly equal concentration of the mono- and di-adenylated species. This report demonstrates that precise mass measurements of PCR products up to 309 kDa (500 bp) can be routinely obtained by ESI-FTICR requiring low femtomole amounts. Copyright 1999 John Wiley & Sons, Ltd.     

An investigation of the oxidized Ni/InAs interface

Ni was resistively deposited onto bulk InAs and subsequently oxidized in an O₂ atmosphere. The anneal temperature and time were 450 °C and 2.5 h, respectively. X-ray diffraction of the oxidized Ni/InAs sample revealed the formation of In₃Ni₂ and In₂O₃ on the front suggesting inter diffusion of In, Ni and O. NiO was not detected by X-ray diffraction. In a preliminary study, using glass as a substrate, NiO readily formed when using these oxidation parameters. Conductivity measurements of the oxidized Ni/InAs surface revealed a conducting front and insulating rear surface while TEM of the Ni/InAs interface revealed an intermediate amorphous diffusion zone between the “oxidized” Ni layer and the bulk InAs. A closer investigation of the intermediate layer supports the X-ray diffraction results, suggesting compound formation due to diffusion of oxygen and nickel into the substrate, and out-diffusion of In and As from the bulk of the sample. AES was used to further elucidate these results.     

A computational study of the effect of an external electric field on the geometry of selected donor–acceptor complexes

To understand the effect of Au and thiol atoms in octane molecule, a structural and charge density analysis has been carried out by high level ab initio quantum chemical calculations using MP2 and B3PW91 methods with the basis sets 6-311G(d,p) and LANL2DZ. The optimized geometries, specifically, the geometry obtained from both levels reveal the effect of S- and Au-atoms in octane molecule. An introduction of sulfur atom in octane molecule lengthen its backbone C–C bond distances, and further adding of Au-atom at the terminals of octane dithiolate stabilizes these distances. The bond densities of the C–C bonds of octane are 1.6 eÅ⁻³, these values are decreased significantly and the charges are largely depleted, when thiol and Au-atoms added in the octane molecule. The presence of negative Laplacian ²ρ(r) at bond critical points of C–C and C–H bonds, indicate, the charges are concentrated in these bonds, confirm that these bonds exhibit an open shell type interaction. The moderate values of density and the negative Laplacian of S–C bonds confirm the covalent character. The positive ²ρ(r) value of Au–S bonds, characterize, the bonding interaction is a closed shell interaction. The combined observed low value of electron density and the positive Laplacian of Au–S bond comprises, the gold and S interaction is not a covalent interaction, but it is a very weak coordination bond interaction. The small positive value of total energy density in Au–S bond indicates, the charges in these bonds are highly depleted and this is further confirmed by the Laplacian of bond characterization.     

A comparison of the M3/M4 metastable defect detected in hydrogen and ICP Ar plasma treated n-GaAs

Defects created by a dc hydrogen plasma have been compared to those observed in n-GaAs exposed to an inductively coupled (ICP) Ar plasma. The reference sample (in the case of H-plasma treated material) contained two prominent native deep level electron traps, possibly M4 and E_C−0.56 eV, which were both passivated by hydrogen. Plasma treatment also resulted in the formation of a defect observed at 0.58 eV (M3) below the conduction band. This defect transforms back into what is believed to be M4 when annealed at 350 K for 3 h under reverse bias. These two defects compare well with two similar defects observed in the Ar ICP treated samples also showing metastable behavior. Additionally, the electrical characterization of Schottky barrier diodes on n-GaAs, prior to and after hydrogen passivation shows that, depending on the plasma conditions, the plasma ions significantly damage the surface resulting in poor rectifying contacts. The damage is considerably reversed/repaired upon annealing between the room temperature and 573 K (300 °C).     

Improved GaSb surfaces using a (NH4)2S/(NH4)2S04 solution

Bulk (1 0 0) n-GaSb surfaces have been treated with a sulphur based solution ((NH₄)₂S/(NH₄)₂SO₄) to which sulphur has been added, not previously reported for the passivation of GaSb surfaces. Au/n-GaSb Schottky barrier diodes (SBDs) fabricated on the treated material show significant improvement compared to that of the similar SBDs on the as-received material as evidenced by the lower ideality factor (n), higher barrier height (?_b) and lower contact resistance obtained. Additionally, the reverse leakage current, although not saturating, has been reduced by almost an order of magnitude at −0.2 V. The sample surfaces were studied by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The native oxide, Sb–O, present on the as-received material is effectively removed on treating with ([(NH₄)₂S/(NH₄)₂SO₄]+S) and (NH₄)₂S. Analysis of the as-received surface by XPS, prior to and after argon sputtering, suggests that the native oxide layer is ≤8.5 nm.     

A theoretical model investigation of the hydrogen-electrode processes of an alkaline H2---O2 fuel cell

Ab initio molecular orbital (MO) and self consistent field (SCF) computations have been carried out within the Restricted Hartree—Fock (RHF) formalism on the species involved in 22 possible reaction mechanisms associated with the anodic process: H₂ → 2H⁺ + 2e⁻ of the hydrogen—oxygen alkaline fuel cell. Such a model, which represents the gas phase reactions, may be regarded as a primary standard for any future study in which the catalyst of the electrode may be included.