掺杂两种荧光染料的有机红光电致发光器件

制作了掺杂rubrene和4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9,enyl)-4H-pyran(DCJTB)两种荧光染料的红光有机电致发光器件。N,N’-diphenyl-N,N’-bis(1-naphthyl)-(1,1’-biphenyl)-4,4’-diamine(NPB)和掺杂的Tri-(8-hydroxyquinoline)aluminum(Alq3)分别作为空穴和电子传输层。我们发现掺rubrene和DCJTB的器件性能与只掺DCJTB的器件性能相比有所提高。器件性能的改善是因为掺入的rubrene能够促进从Alq3到DCJTB的能量转移。根据荧光衰减曲线,计算出从Alq3到DCJTB、从Alq3到rubrene以及从rubrene到DCJTB的能量转移速率分别为1.04×109,3.89×109,2.79×109s-1。可以看出能量通过rubrene从Alq3到DCJTB的转移速率是能量直接从Alq3到DCJTB的2.7倍。     

Synthesis,characterization, and curing kinetics of novel ladder‐like polysilsesquioxanes containing side‐chain maleimide groups

Two ladder‐like polysilsesquioxanes (LPS) containing side‐chain maleimide groups have been synthesized successfully by reacting N‐(4‐hydroxyphenyl)maleimide (HPM) with LPS containing 100 mol % of chloropropyl groups (Ladder A ) and 50 mol % of each methyl and chloropropyl group (Ladder B ). HPM was synthesized by reacting maleic anhydride with 4‐aminophenol, and the resulting amic acid was imidized using p‐toluenesulfonic acid as a catalyst (Scheme 1 ). The LPSs were characterized by Fourier transform infrared (FTIR), ¹H nuclear magnetic resonance (NMR), proton‐decoupled ¹³C NMR, ²⁹Si NMR, wide‐angle X‐ray diffraction (WAXD), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). Characterization indicated that these polymers had ordered ladder‐like structures with possible defects. These polymers were soluble in common solvents at ambient temperature, which suggested that they were not crosslinked. Both the polymers and the HPM were cured, and their kinetics were followed by dynamic DSC. The Ozawa and Kissinger methods were used to calculate activation energies for curing. Curing increased the temperature at which both 5% weight loss and maximum rate of weight loss were observed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4036–4046, 2004     

Mutual influence of the morphology and capillary rheological properties in nylon/glass‐fiber/liquid‐crystalline‐polymer blends

Nylon‐6/glass‐fiber (GF)/liquid‐crystalline‐polymer (LCP) ternary blends with different viscosity ratios were prepared with three kinds of nylon‐6 with different viscosities as matrices. The rheological behaviors of these blends were characterized with capillary rheometry. The morphology was observed with scanning electron microscopy and polarizing optical microscopy. This study showed that although LCP did not fibrillate in binary nylon‐6/LCP blends, LCP fibrillated to a large aspect ratio in some ternary blends after GF was added. The addition of 5 wt % LCP significantly reduced the melt viscosity of nylon‐6/GF blends to such an extent that some nylon‐6/GF/LCP blends had quite low viscosities, not only lower than those of neat resins and nylon‐6/GF blends but also lower than those of corresponding nylon‐6/LCP blends. The mutual influence of the morphology and rheological properties was examined. The great reduction of the melt viscosity was considered the result of LCP fibrillation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1619–1627, 2004     

Effect of α‐cyclodextrin on the crystallization of poly (3‐hydroxybutyrate)

The effect of α‐cyclodextrin (α‐CD) on the crystallization behavior of poly(3‐hydroxybutyrate) (PHB) was investigated with polarized optical microscopy, differential scanning calorimetry, and wide‐angle X‐ray diffraction. We found that the addition of α‐CD can greatly accelerate the crystallization of PHB and that α‐CD has a potential not only to enhance the nucleation but also to accelerate the crystallization of PHB. Compared to a conventional nucleation agent, such as talc, α‐CD is a natural product and has many advantages because it is environmentally friendly and safe to humans. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3461–3469, 2004     

0.8W/80K直线驱动斯特林制冷机的研制

介绍了一种 0 .8W/ 80 K分置式斯特林制冷机。该制冷机采用当前国外先进的直线电机驱动 ,双活塞对称布置结构。该制冷机已通过军品所要求的环境试验 ,输入功率小于 4 0 W(DC)情况下 ,其 +6 0℃高温环境下制冷量≥ 0 .5 W/ 80 K ,带载 0 .5 W工况下 MTTF已突破 2 0 0 0小时。文中主要论述了其工作原理、结构特点、试验情况。     

多目标优化发射层析算法在等离子体场光谱诊断中的应用

提出一种基于多目标优化原理的发射光谱层析(EST)图像重建新算法MCIRT.通过计算机数值 模拟，考察了该算法对非对称发射系数场分布的重建效果.结果表明，与传统层析算法相比 ，MCIRT算法具有收敛快，重建精度高的优势，适合于非完全数据情况下的等离子体发射系 数场重建，并且实时性更好.作为一个应用实例, 运用谱线相对强度法重建了自由电弧等离 子体的三维温度及粒子数密度分布. 关键词： 等离子体诊断 图像重建     

A Novel Model for Protein Immobilization on Microspheres

The immobilization of proteins, especially receptor proteins commonly used in high through-put screening of drugs (HTS), have received great attention in recent years. There are many successful isothermal models for describing the adsorption of protein onto solid surface, such as Langmuir model, Bi-Langmuir model, Fowler model, Freundlich model, Freundlich-Langmuir model and Tekmin model etc. In all these models, Langmuir model was the most favorable one model accepted by many researchers, but the experimental results showed that it was not entirely fit to all adsorption behaviors. So new models were required for describing protein adsorption onto microspheres in different conditions.In our research, a novel isothermal model, including Langmuir and other adsorbing behaviors was presented basing on the holding degree of surface active sites and the interaction styles of protein immobilization. In Langmuir model, the adsorbing amount of protein was described as [PS] =Km[P]/1 + K[P], where [PS] was the concentration of adsorbed protein, [P] was the concentration of freeprotein at equilibrium state, and Km and K was constant. According to the interactions of protein and ligands, there were three patterns in the interactions of protein and ligands. On the similar assumption that the interaction of protein and microspheres were three styles, and based on the definition of the holding degree of surface active sites (Y), three adsorption behaviors could be described as Y K[ P ]φ/ K[P]φ+1 or ln K + φ ln[P] =ln(Y/1-Y) in which [P] was the concentration of free protein at equilibrium state, and φ and K was constant. Different scale of φ presented different adsorption behaviors, especially when φ was 1, the adsorption behavior was Langmuir adsorbing model. Figure I indicated the different adsorbing results in different adsorption behaviors (φ＞1, φ＜1,and φ=1).     

Synthesis of Cationic PEM Emulsion and Application in Waste Water Treatment

Cationic polymer as a kind of flocculant is widely applied in purification treatment of waste water. Because it has positive charge group, it is able to connect strongly the suspended matters, short cellulose and other microparticles. The research on synthesis of cationic polymer and application in treatment of waste water is very universal abroad. But domestic research on those is not general. The technology of synthesis of PEM is simple, and the production cost is low. It is easy to apply in treatment of waste water.Synthesis of PEM Emulsion FlocculantSome distilled water, PVA(poly(vinyl alcohol)), EA(ethyl acrylate), and K2S2O8(potassium persulfate) were put into reaction vessel. Kept stirring up under nitrogen. When heated the solution to 40℃, dropped the water solution of MTA[(2-methacryloxylethyl)trimethyl ammonium].Maintained the temperature at 70℃, reacted about 7-8 hours. Then got the PEM emulsion. Changed the ratio of EA and MTA. Obtained a series of PEM emulsions.Stability and Convertibility of PEM EmulsionThe test results showed that when the EA/MTA was 85/15, the PEM emulsion was most stable.When the total monomer quantity was 35%, the convertibility of PEM emulsion was the highest,i.e.98.6%.The MTA Copolymerization Ratio and Morphology of PEM EmulsionWhen the monomers EA/MTA=85/15 and total monomer quantity was 35%, the MTA copolymerization ratio of PEM emulsion was 95.15%(the highest), and the PEM emulsion was some microspheres with 100-180nm of diameter.The Test Results of PEM Emulsion in Treatment of Waste Water The PEM emulsion flocculant was applied in treatment of waste water of paper mill, and measured the precipitation time(t) and transmittancy(T). The test results were showed in table 1. The optimum value of PEM which was able to make the waste water of paper mill into clear water was 0.008%.     

PURIFICATION OF L-METHIONINE AND N-ACETYL-D-METHIONINE FROM THE MIXTURE OF ENZYMATICALLY DEACYLATED N-ACETYL-DL-METHIONINE

1. INTRODUCTION Methionine, namely 2-amido-4-thiomethyl butyric acid with a structure of CH3SCH2CH2CHCOOH, is one of the essential amino acids and has two natural enantionmers, D and L-methionine. The mixture of L- and D-isomers can be used as analeptics or nutritive additives to maintain the equilibrium of amino acids of feed [1,2]. L-methionine can release active methyl and accelerate the synthesis of choline, which further speeds up the conversion of the lipid accumulated in liv…     

The Research on Polymer Microcapsulation for Cell Technology

Microcapsulation is a technology that enwrapped the solid or liquid or some gas matter with membrane materials to form microparticles(i.e.microcapsules). The materials of microcapsule is composed of naturnal polymers or modified naturnal polymers or synthesized polymers. The water-soluble core matter can only use oil-soluble wall materials, and vice versa.Synthesized methods of polymer microcapsulesSynthesized methods with monomers as raw materialsThis kind of methods include suspension polymerization, emulsion polymerization, dispersal polymerization, precipitation polymerization,suspension condensation polymerization, dispersal condensation polymerization, deposition condensation polymerization, interface condensation polymerization, and so on.Synthesized methods with polymers as raw materialsThese methods are suspension cross-linked polymerization, coacervation phase separation,extraction with solvent evaporation, polymer deposition, polymer chelation, polymer gel,solidification of melting polymer, tray-painted ways, fluidized bed ways, and so forth.Polymer materials to synthesize microcapsules2.1. Naturnal polymer materialsThe characteristics of this kind of materials are easy to form membrane, good stability and no toxicity. The polymer materials include lipids(liposome), amyloses, proteins, plant gels, waxes, etc.2.2. Modified polymer materialsThe characteristics of these materials are little toxicity, high viscidity(viscosity), soluble salt materials. But they cannot be used in water, acidic environment and high temperature environment for a long time. The materials include all kind of derivants of celluloses.2.3. Synthesized polymer materialsThe characteristics of the materials are easy to form membrane, good stability and adjustment of membrane properties. The synthesized polymer materials include degradable polymers(PLA, PGA,PLGA, PCL, PHB, PHV, PHA, PEG, PPG and the like) and indegradable polymers(PA, PMMA,PAM, PS, PVC, PB, PE, PU, PUA, PVA and otherwise).The applications of polymer microcapsules in cell technologyThe "artificial cell" is the biological active microcapsule used in biological and medical fields.The applications of cells (including transgenic cells, the same as artificial cells) technology include several aspects as follows:3.1. Microcapsulation of artificial red cell3.2. Microcapsule of artificial cell of biological enzyme3.3. Microcapsule of artificial cell of magnetic material3.4. Microcapsule of artificial cell of active carbon3.5. Microcapsule of active biological cell