钛纳米管负载锰催化剂的低温选择性催化还原脱硝性能

采用水热法合成了钛纳米管（TiNT）,以400℃焙烧后得到的TiO₂纳米管为载体,采用浸渍法制备了MnO_x/TiNT催化剂,用于低温NH₃选择性催化还原脱NO反应（SCR）。BET、TEM、XRD及TG测试表明,经过400℃焙烧之后的钛纳米管主要成分为锐钛矿型TiO₂,所制备的催化剂活性组分分散性较好。在模拟烟气条件下,考察了锰负载量、空速、O₂含量、氨氮比及进口NO浓度对MnO_x/TiNT的SCR催化性能的影响。在150℃、\[NH₃\]/\[NO\]比为1.2、O₂浓度为3%、NO浓度为0.06%、空速GHSV为23613.8h^-1、Mn的负载量为5%~15%的条件下,NO的转化率达到95%以上。反应气氛中单独通入水会造成催化剂的活性下降;切断H₂O,催化剂的活性可以恢复至初始水平。温度越高,催化剂抗水性能越好,而且水存在情况下的抗硫性能优于其单独抗硫性能。再次切断H₂O和SO₂,催化剂的活性逐渐上升,但不能恢复到初始水平。     

The use of ethylene glycol solution as the running buffer for highly efficient microchip-based electrophoresis in unmodified cyclic olefin copolymer microchips

An ethylene glycol solution was used as the electrophoretic running buffer in unmodified cyclic olefin copolymer (COC) microchips to minimize the interactions between the analytes and the hydrophobic walls of the plastic microchannels, enhance the resolution of the analytes and eliminate the uncontrollable dispersion caused by uneven liquid levels and non-uniform surfaces of the separation channels. Five amino acids that were labeled with fluorescein isothiocyanate (FITC) were used as model analytes to examine the separation efficiency. The effects of ethylene glycol concentration, pH and sodium tetraborate concentration were systematically investigated. The five FITC-labeled amino acids were effectively resolved using a COC microchip with an effective length of 2.5 cm under optimum conditions, which included using a running buffer of 20 mmol/L sodium tetraborate in ethylene glycol:water (80:20, v/v), pH 6.7. A theoretical plate number of 4.8 × 10(5)/m was obtained for aspartic acid. The system exhibited good repeatability, and the relative standard deviations (n=5) of the peak areas and migration times were no more than 3.4% and 0.7%, respectively. Furthermore, the system was successfully applied to elucidate these five amino acids in human saliva.     

Surface modification of PDMS by surface-initiated atom transfer radical polymerization of water-soluble dendronized PEG methacrylate

The current paper reports the synthesis of a highly hydrophilic, antifouling dendronized poly(3,4,5-tris(2-(2-(2-hydroxylethoxy)ethoxy)ethoxy)benzyl methacrylate) (PolyPEG) brush using surface initiated atom transfer radical polymerization (SI-ATRP) on PDMS substrates. The PDMS substrates were first oxidized in H₂SO₄/H₂O₂ solution to transform the Si-CH₃ groups on their surfaces into Si-OH groups. Subsequently, a surface initiator for ATRP was immobilized onto the PDMS surface, and PolyPEG was finally grafted onto the PDMS surface via copper-mediated ATRP. Various characterization techniques, including contact angle measurements, attenuated total reflection infrared spectroscopy, and X-ray photoelectron spectroscopy, were used to ascertain the successful grafting of the PolyPEG brush onto the PDMS surface. Furthermore, the wettability and stability of the PDMS-PolyPEG surface were examined by contact angle measurements. Anti-adhesion properties were investigated via protein adsorption, as well as bacterial and cell adhesion studies. The results suggest that the PDMS-PolyPEG surface exhibited durable wettability and stability, as well as significantly anti-adhesion properties, compared with native PDMS surfaces. Additionally, our results present possible uses for the PDMS-PolyPEG surface as adhesion barriers and anti-fouling or functional surfaces in biomedical applications.     

Syntheses, structures and luminescent properties of a series of 3D lanthanide coordination polymers with tripodal semirigid ligand

Reactions of the tripodal bridging ligand 5-(4-carboxy-phenoxy)-isophthalic acid (abbreviated as H₃cpia) with lanthanide salts lead to the formation of a family of different coordination polymers, that is, [Ln(cpia)(H₂O)₂]_n·nH₂O (Ln=Ce (1), Pr (2), Nd (3), Sm (4), Eu (5), Gd (6), Dy (7), Er (8), Tm (9) and Y (10)) in the presence of formic acid or diethylamine, which are characterized by elemental analysis, IR spectrum, thermogravimetric analysis (TGA), XRPD spectrum and single-crystal X-ray diffraction. Compounds 1-10 are isostructural and exhibit three-dimensional microporous frameworks. Furthermore, the photoluminescent properties of 4, 5 and 7 have been studied in detail.     

TiO_2空心微球负载钒、铈催化剂的制备及其对氯苯催化燃烧性能研究

采用水热法制备TiO2空心球,以TiO2空心球为载体,采用等体积浸渍法分别制备了不同V负载量(3%~10%)的V2O5/TiO2和稀土改性后的V2O5-CeO2/TiO2催化剂,利用XRD,SEM,EDS,TEM对TiO2空心球及V2O5-CeO2/TiO2催化剂进行了表征,结果表明,空心球TiO2分散性良好,粒径在1.5μm左右,且其为锐钛矿结构,负载的V和大部分的Ce均匀分散在TiO2空心球体内部或者表面而未破坏TiO2空心球结构。考察了催化剂对氯苯的催化燃烧性能,活性评价结果表明当V负载量在5%时,V2O5/TiO2催化剂对氯苯催化燃烧性能最佳,在掺杂10%的稀土Ce后,催化燃烧氯苯的活性得到明显提高。     

十二烷基硫酸钠对甲烷水合物生成过程影响研究

根据甲烷水合物含气率高、分解速度慢等特性,提出利用高压注水技术和表面活性剂促进作用促使矿井瓦斯水合化以预防煤与瓦斯突出的思路。进行了3·6~12℃、7·82~12·26MPa条件下两种浓度体系(10mmol/L和0·3mmol/L)中十二烷基硫酸钠(SDS)对甲烷水合物作用效果的实验研究,结合水合物诱导时间、生成速度及含气率等计算对实验数据进行了分析,并运用表面张力法测得8℃时SDS溶液的临界胶束浓度(CMC)为2·5mmol/L。结果表明,高浓度体系对水合物生成速度、含气率的影响较之低浓度体系的更强,但是低浓度体系中水合物生成的诱导时间却较短,表面活性剂溶液浓度超过其CMC后对水合物的生成影响显著。     

直接甲醇燃料电池的稳定性

综述了近年来在直接甲醇燃料电池性能衰减方面的研究进展, 探讨了影响电池运行稳定性的主要因素.     

微层共挤出(PP+EVOH)/PP阻隔材料的结构与性能研究

利用微层共挤出技术制备了具有交替层状结构的(PP+EVOH)/PP复合材料,其中PP为聚丙烯,EVOH为乙烯-乙烯醇其聚物.通过扫描电子显微镜观察、气体渗透实验、差示扫描量热仪分析以及力学性能测试研究了微层共挤出复合材料的形态结构及其对复合材料气体阻隔性能、力学性能以及结晶性能的影响.研究结果表明,通过微层共挤出技术,PP层和(PP+EVOH)层沿挤出方向交替排列,EVOH在PP基体中的的分散形态由零维球形变为一维纤维状,进而演变为二维片状.这些形态导致微层共挤出材料的氮气渗透系数和断裂伸长率较普通共混物分别下降了两个数量级和提高了27倍,并且显著影响其结晶行为.当层数超过64层后,由于PP层减薄,界面增多,EVOH不仅对(PP+EVOH)层中PP相存在结晶成核作用,而且对PP层也有结晶成核作用.     

Extraction of formic and acetic acids from aqueous solution by dynamic headspace-needle trap extraction temperature and pH optimization

A combined method of dynamic headspace-needle trap sample preparation and gas chromatography for the determination of formic and acetic acids in aqueous solution was developed in this study. A needle extraction device coupled with a gas aspirating pump was intended to perform sampling and preconcentration of target compounds from aqueous sample before gas chromatographic analysis. The needle trap extraction (NTE) technique allows for the successful sampling of short chain fatty acids under dynamic conditions while keeping the headspace (HS) volume constant. Two important parameters, including extraction temperature and effect of acidification, have been optimized and evaluated using the needle trap device. The method detection limits for the compounds estimated were 87.2microg/L for acetic acid and 234.8microg/L for formic acid in spite of the low flame ionization detection response for formic acid and its low Henry's law constant in aqueous solution. Precision was determined based on the two real samples and ranged between 4.7 and 10.7%. The validated headspace-needle trap extraction method was also successfully applied to several environmental samples.