聚醚型脂肪族聚氨酯预聚体的制备

以ＨＤＩ为异氰酸酯组分，制备聚醚型脂肪族聚氨酯预聚体。对聚醚脱水条件，反应温度和时间，以及预聚体的一些性能进行了探索。     

γ-LiAlO2晶体生长、改性和热学性质研究

采用快速提拉法生长出了透明、完整的γ-LiAlO2晶体,但是晶体的高熔点和易挥发性限制了γ-LiAlO2晶体质量.采用气相传输平衡法(vapor transport equilibration technique,VTE)工艺对晶体改性,半高宽(FWHM)值从116.9arcsec降至44.2arcsec,继续升高VTE处理温度至1300℃,FWHM值反而升高至55.2arcsec.快速提拉法生长出来晶体,[100]方向和[001]方向的热膨胀系数分别为17.2398×10-6/K,10.7664×10-6/K.经过三步VTE处理后[100]和[001]方向热膨胀系数降至16.6539×10-6/K和10.1784×10-6/K.     

上皮生长因子预防心脏术后心包粘连的实验及临床研究

目的探讨上皮生长因子(EGF)对心脏术后心包粘连的预防作用.方法术中对犬心包内喷洒上皮生长因子3个月后,观察心包粘连情况;选先天性心脏病、房缺及室缺病人40例,术中心包内喷洒上皮生长因子,术后6个月、12个月经CT检查,判定心包粘连、增厚结果.结果在动物实验和临床研究中,实验组粘连程度显著低于对照组(P<0.01).结论 EGF心包内应用有明显预防心脏术后心包粘连的作用.     

喷气式Z箍缩等离子体辐射软X射线能谱的研究

研制了一台五通道ROSS-FILTER-PIN软X射线能谱仪，能谱范围为0.28—1.56keV.它由5个连续能段组成，每个能段的起止边由罗斯滤片对(ROSS-FILTERS)的L或K吸收边确定.罗斯滤片对的厚度通过优化计算得到，为了使每个通道的灵敏区外响应(即所测能段外响应)与通道总响应之比最小，在滤片对的第二滤片上镀上了一定厚度的第一滤片材料；为了缩减滤片表面积以增强低能滤片的抗冲击能力及方便滤片加工，能谱仪采用了小探测面积的PIN探测器(1mm²).借助此能谱仪，测量得到了喷气式Z箍缩(Z-pinch)等离子体辐射软X射线能谱的分布，并研究了软X射线产额随箍缩状况的变化趋势. 关键词： Z箍缩等离子体 罗斯滤片 软X射线能谱     

Photoluminescence characteristics of ZnTiO3: Bi nanocrystals

The photoluminescence properties of the Bi³⁺ in sol-gel derived ZnTiO₃ nanocrystals have been investigated. An ultra-violet emission at 360 nm and a visible emission band at 506 nm have been observed, originating from two kinds of emission centers. The former is ascribed to the ³P₁-¹S₀ transition of Bi³⁺ and the latter to the recombination of the electrons with the photo-generated holes trapped in the zinc vacancies. In all cases the latter contribution is predominant.     

高斯光束计算平板波导自由传输区远场分布及其修正

对近轴近似条件下求解亥姆霍兹方程得到的高斯光束显式传播公式做了分析，同时，基于基尔霍夫衍射理论，在菲涅耳近似的条件下给出了相应的高斯光束在远场的传播公式，在此基础上，对近轴近似条件做出了定量分析，给出了这个近似条件引入的误差，提出了一种计算高斯光束远场分布的修正方法，并采用有限差分-光束传播方法(FD-BPM)来检验各种方法的准确性。把这种修正方法应用到平面光集成波导器件，如阵列波导光栅(AWG)、蚀刻衍射光栅(EDG)等器件的设计和模拟中，可以大大降低工作的复杂性，同时可以得到精确的结果。     

Hierarchical structures in a turbulent pipe flow

A hierarchical structure (HS) analysis (β-test and γ-test) is applied to a fully developed turbulent pipe flow. Velocity signals are measured at two cross sections in the pipe and at a series of radial locations from the pipe wall. Particular attention is paid to the variation of turbulent statistics at wall units 10<y⁺<3000. It is shown that at all locations the velocity fluctuations satisfy the She–Leveque hierarchical symmetry (Phys. Rev. Lett. 72 (1994) 336). The measured HS parameters, β and γ, are interpreted in terms of the variation of fluid structures. Intense anisotropic fluid structures generated near the wall appear to be more singular than the most intermittent structures in isotropic turbulence and appear to be more outstanding compared to the background fluctuations; this yields a more intermittent velocity signal with smaller γ and β. As turbulence migrates into the logarithmic region, small-scale motions are generated by an energy cascade and large-scale organized structures emerge which are also less singular than the most intermittent structures of isotropic turbulence. At the center, turbulence is nearly isotropic, and β and γ are close to the 1994 She–Leveque predictions. A transition is observed from the logarithmic region to the center in which γ drops and the large-scale organized structures break down. We speculate that it is due to the growing eddy viscosity effects of widely spread turbulent fluctuations in a similar way as in the breakdown of the Taylor vortices in a turbulent Couette–Taylor flow at high Reynolds numbers.     

二氧化氯在炼油循环水中的杀菌除泥作用

采用强氧化剂二氧化氯对炼油循环水进行杀菌灭藻、除垢和减缓腐蚀现场试验研究 ,且对试验结果进行了分析 .结果表明 :稳定性二氧化氯可有效控制炼油循环水中微生物量 ,加药量约 1mg/L ,2 4h后杀菌率达 10 0 % ;同时减少粘泥在热交换设备上的形成 ,有效除去污垢 ,使缓蚀剂发挥作用 ,腐蚀速率明显减小 (小于 0 .1mm /a) ,循环水浊度小于 10mg/L ;加药量小于 1mg/L时其对有机磷水稳定剂的影响小 .     

POROSITY CALCULATION OFMIXTURES OF FIBROUS PARTICLES

The initial forming of fiber blend to high green density, i.e. the packing of fibrous particles, is important to the reinforcement of composite materials. It is very useful to develop a general predictive method for the optimum selection of particle mixtures for the property control of ceramic or composite products. This paper presents such a mathematical model developed on the basis of the similarity analysis between the spherical and non-spherical particle packings and assesses its applicability to the packing of fibrous particles with discrete and/or continuous length distributions. The results indicate that the model can predict this packing system well and hence provide an effective way to solve various packing problems in the composite materials processing.