面向学生的个性化智能型教学平台的构成和应用

本文结合“电大在线”教学平台和作者开发的个性化智能学习服务系统,依据现代教学设计理论和学习理论建立了面向学生的个性化智能教学平台的组成模块,分析了各模块的特点,并设计教学平台,支持面向学生的个性化教学。     

非完整系统Tzénoff方程的Mei对称性和守恒量

研究了在群的无限小变换下非完整系统Tzénoff方程的Mei对称性，给出了非完整系统Tzénoff方程Mei对称性的定义和判据方程.给出了这种Mei对称性导致Lie对称性的充要条件，通过特殊Mei对称性条件下的Lie对称性，找到了非完整系统Tzénoff方程的Hojman守恒量.     

Growth,spectroscopic and laser properties of Yb<Superscript>3<Emphasis Type="Bold">+</Emphasis></Superscript>-doped GdAl<Subscript>3</Subscript>(BO<Subscript>3</Subscript>)<Subscript>4</Subscript> crystal: a candidate for infrared laser crystal

Yb³⁺:GdAl₃(BO₃)₄ (hereafter Yb³⁺:GAB) crystals with large sizes and good optical quality have been grown by the top-seed solution growth (TSSG) method. The polarized absorption and emission spectra have been investigated at room temperature. For the σ-polarization, the intensities of both absorption and emission spectra are stronger than those for the π-polarization, the σ-absorption cross section of Yb³⁺ in GAB being 3.43×10^-20 cm² at 977 nm, and the σ-emission cross section being 0.98×10^-20 cm² at 1045 nm. The fluorescence lifetime of the ² F _5/2→² F _7/2 transition was measured to be 800 μs in the 5% doped sample used for our laser experiments, 993 μs in a 10% doped sample and 569 μs in a 0.5% doped sample. The laser parameters were estimated as: β_min=0.022, I_sat=10.4 kW/cm² and I_min=0.23 kW/cm². About 0.4 W laseroutput at the wavelength of 1043 nm was achieved when the Yb³⁺:GAB crystal was pumped by a 974 nm laser diode, with 27.4% slope efficiency. PACS 42.55.-f; 42.70.Hj; 78.20.-e; 81.10.Dn     

Electron spin resonance from annealed titania nanotubes

Titania nanotubes were prepared using a hydrothermal method. Hydrogen titanate nanotubes (H-TNTs) with an anatase phase changed to anatase nanocrystals at about 500 °C, and then a rutile structure at ∼800 °C. A sharp and symmetrical electron spin resonance (ESR) signal (g=2.003), attributed to a single-electron-trapped oxygen-vacancy (SETOV), was obtained at the annealed H-TNTs (T<500 °C). The SETOV signal increased and maximized remarkably at about 400–500 °C. Then, the nanotube structure appeared to be demolished. Yet, when the vacuum-heated H-TNTs were sealed in N₂ or Ar ambient, some additional ESR signals appeared besides the SETOV signal. The broad asymmetric ESR signal (g=1.98) was attributed to a surface oxygen vacancy related to the Ti³⁺ sites in a reduced TiO₂ matrix. The vacuum-heated sodium titanate nanotubes (Na-TNTs) showed only the SETOV signal (T<500 °C). PACS 61.46.Fg; 61.72.Ji; 76.30.-v     

Effects of different sintering temperature and Nb2O5 content on structural and magnetic properties of Z-type hexaferrites

Nb-doped Z-type hexaferrites (Ba₃(Co_0.4Zn_0.6)₂Fe₂₄O₄₁) with composition of Ba₃(Co_0.4Zn_0.6)₂Fe₂₄O₄₁+x Nb₂O₅ (where x=0.0, 0.1, 0.2, 0.4, 0.6, 0.8, 1.2, 1.6 and 2.0 wt%) were prepared by a solid-state reaction method. The effects of different sintering temperature (T_s) and Nb₂O₅ content on the sintering behaviors, phase composing, microstructure, and magnetic properties of the samples were investigated. The results from X-ray diffraction and scanning electron microscopy show that as the amount of Nb₂O₅ additive increases, the major phase changes to Z-phase, Simultaneously, M-phase and a small amount of niobate phase appear. The Nb₂O₅ additive promotes the grain growth as reaction center at lower sintering temperature (1220 °C), but at higher temperature (1260 °C), niobate phase separated out in grain boundaries as secondary phase will restrain abnormal grain growth, so closed pores in grains are not formed. The Nb₂O₅ additive can enhance densification, improve initial permeability of hexaferrites by increasing the grain growth of hexaferrite and the displacement of ions in the sintering process due to the aberration and activation of crystal lattice, which is accompanied by the solubility of Nb⁵⁺ in the hexaferrites. A relative density of 96%, maximum initial permeability (32–33), minimum coercivity (454–455 A/m) and resonance frequency above 400 MHz were obtained for the sample with 0.8 wt% Nb₂O₅ sintered at 1260 °C for 6 h.     

The influence of preparative parameters on the adhesion of alumina washcoats deposited on metallic supports

Well-adhered alumina washcoats on FeCrAl metallic supports were prepared using boehmite sols and alumina slurries. The microstructure and the surface performance of the washcoat/support were investigated by SEM, XRD, and ultrasonic vibration. The effects of the main preparative parameters on the coating adherence were studied. The optimal coating conditions are presented as follows: pre-oxidation of the metallic supports was performed at 900 °C for 10 h, the sol layer loadings were 2.0-6.6 wt.%, and the slurry layer loadings were less than 25.3 wt.%. The sol layer drying was performed at 30 °C for 1 h and that for the slurry layer the drying was performed at 120 °C for 2 h, and the coating calcining was performed at 900 °C for 2 h. The SEM photographs of coated samples show that alumina washcoats were well deposited on the metallic supports.     

Hyperchaos generated from the Lorenz chaotic system and its control

In this Letter, a hyperchaotic Lorenz system is constructed via state feedback control. Abundant dynamics of the hyperchaotic system is studied using the Lyapunov exponents, Poincaré section and bifurcation diagram. Furthermore, effective linear feedback controllers are designed for stabilizing hyperchaos to unstable equilibrium, periodic orbits and quasi-periodic orbit. Numerical simulations are given to illustrate and verify the results.     

北京同步辐射装置3W1B软X射线光束线偏振特性测量

应用自行研制的Mo/Si周期多层膜作为起偏器和检偏器的光学元件, 测量了北京同步辐射装置3W1B束线的偏振状态. 通过数据分析, 得到了3W1B软X射线的有关偏振参数, 在86—89eV能区经过起偏器后的偏振度超过98%, 圆偏振分量介于1%—3%之间.     

Tuning the wettability of calcite cubes by varying the sizes of the polystyrene nanoparticles attached to their surfaces

The wettability of calcite cubes was tuned by varying the sizes of the polystyrene nanoparticles attached to their surfaces via a dispersion polymerization. The products were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersion spectrum (EDS) and Fourier transformation infrared spectrum (FTIR). The results showed that the hydrophobicity of the calcite cubes was enhanced with the increase of the size of the polystyrene nanoparticles attached. Using polystyrene nanoparticle-attached calcite cubes (PNACC) as emulsifiers, stable water-in-tricaprylin Pickering emulsions were produced. By gelling the water droplets of the Pickering emulsions, the hierarchical structures of polystyrene nanoparticle-attached calcite cube-armored microspheres were obtained. The polystyrene nanoparticle-attached calcite cubes were expected to have novel surface properties similar neither to traditional Pickering particles, nor to macroscopically asymmetrical Janus particles.     

The influence of fiber dispersion on the code form of the optical mm-wave signal generated by single sideband intensity-modulation

We have theoretically investigated the transmission performance of the optical mm-wave generation by using an external modulator based on single sideband (SSB) intensity modulation. Though the SSB millimeter (mm)-wave can immune the fading effect, the baseband signals with a high bit rate are degraded greatly after transmission along fiber. The main reason is that the fiber dispersion causes the time shift of the code edges; therefore the maximum transmission distance of the baseband signals is limited. The experimental and simulation results agree well with our theoretical analysis. We also propose a novel scheme to extend the transmission distance. In this novel scheme, the data signals are modulated only onto one of the two optical carriers; hence the shift of the code edges in the down-converted signals after transmission is eliminated.