Nanocomposite hydrogel consisting of Na‐montmorillonite with enhanced mechanical properties

A new kind of nanocomposite (NC) hydrogel with Na‐montmorillonite (MMT) is presented in this article. The NC hydrogels were synthesized by free radical copolymerization of acrylamide and (3‐acrylamidopropyl) trimethylammonium chloride (ATC) in the presence of MMT and N,N′‐methylene‐bis‐acrylamide used as chemical cross‐linker. Due to the cation‐exchange reaction between MMT and ATC (cationic monomer) during the synthesis of NC hydrogels, MMT platelets were considered chemical “plane” cross‐linkers, different from “point” cross‐linkers. With increasing amount of MMT, the crosslinking degree enhanced, causing a decrease of the swelling degree at equilibrium. Investigations of mechanical properties indicated that NC hydrogels exhibited enhanced strength and toughness, which resulted from chemical interaction between exfoliated MMT platelets and polymer chains in hydrogels. Dynamic shear measurements showed that both storage modulus and loss modulus increased with increasing MMT content. The idea described here provided a new route to prepare hydrogels with high mechanical properties by using alternative natural Na‐MMT. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1020–1026     

Strategies for synthesizing non-bioaccumulable alternatives to PFOA and PFOS

This minireview describes the strategies for synthesis of fiuorinated surfactants potentially nonbioaccumulable.Various strategies have been focused on(Ⅰ) reducing the length of the perfluorocarbon chain,(Ⅱ) introducing hetero atoms into the fluorocarbon chain,(Ⅲ) introducing branch(herein and after branch means the fluoro-carbon chain section is not straight).In most cases,the surface tensions versus the surfactant concentrations have been assessed.These above strategies led to various highly fiuorinated(perfluorinated or not perfluorinated) surfactants whose chemical changes enabled to obtain novel alternatives to perfluorooctanoic acid(PFOA) and perfluorooctane sulphonate(PFOS).     

基于盒维数的锚杆工作荷载无损检测研究

为研究锚杆工作荷载,应用了分形理论中的盒维数方法。根据一维杆波动理论,在锚杆外露端头安装一个自激式加速度传感器,利用锚杆无损检测加载试验台分级加载、检测标定测得锚杆-围岩相互作用体系在激发荷载作用下的速度响应,计算其加速度响应曲线的盒维数,拟合得出荷载-盒维数曲线,直观地判断锚杆工作荷载和锚固质量。     

磁流变液中磁性颗粒成链与团聚的临界特征分析

热运动对纳米级磁流变液系统的颗粒团聚行为和宏观流变特性扰动影响不可忽视.为研究施加外磁场后系统微结构与热运动间的关系，探讨在不同颗粒粒径情况下热运动能量在系统总能量中的占比.采用CCD设计方法，分析Monte Carlo仿真获取的颗粒位形信息，生成关于外磁场磁感应强度、颗粒粒径和体积分数的系统热耦合系数<λ>回归模型;成链团聚的临界颗粒粒径计算值比文献经验值高出约23%，证实在考虑系统内多因素的综合影响下，纳米级磁流变液具有更严格的流变现象临界发生条件.     

Effects of Strain Rate,Temperature and Grain Size on the Mechanical Properties and Microstructure Evolutions of Polycrystalline Nickel Nanowires: A Molecular Dynamics Simulation

Through molecular dynamics(MD)simulation,the dependencies of temperature,grain size and strain rate on the mechanical properties were studied.The simulation results demonstrated that the strain rate from 0.05 to 2 ns~(–1 )affected the Young’s modulus of nickel nanowires slightly,whereas the yield stress increased.The Young’s modulus decreased approximately linearly;however,the yield stress firstly increased and subsequently dropped as the temperature increased.The Young’s modulus and yield stress increased as the mean grain size increased from 2.66 to6.72 nm.Moreover,certain efforts have been made in the microstructure evolution with mechanical properties association under uniaxial tension.Certain phenomena such as the formation of twin structures,which were found in nanowires with larger grain size at higher strain rate and lower temperature,as well as the movement of grain boundaries and dislocation,were detected and discussed in detail.The results demonstrated that the plastic deformation was mainly accommodated by the motion of grain boundaries for smaller grain size.However,for larger grain size,the formations of stacking faults and twins were the main mechanisms of plastic deformation in the polycrystalline nickel nanowire.     

唐代试律诗诗题用典与唐代祥瑞尚奇文化

唐代试律诗诗题对有关祥瑞及灵异之类典故的大量选用,不但体现了唐代统治者借祥瑞文化维护自身统治的治国策略,也表明了尚奇之风在唐代的盛行。     

Metabolic profiles of dioscin in rats revealed by ultra‐performance liquid chromatography quadrupole time‐of‐flight mass spectrometry

Dioscin (DIS), one of the most abundant bioactive steroidal saponins in Dioscorea sp., is used as a complementary medicine to treat coronary disease and angina pectoris in China. Although the pharmacological activities and pharmacokinetics of DIS have been well demonstrated, information regarding the final metabolic fates is very limited. This study investigated the in vivo metabolic profiles of DIS after oral administration by ultra‐performance liquid chromatography quadrupole time‐of‐flight mass spectrometry method. The structures of the metabolites were identified and tentatively characterized by means of comparing the molecular mass, retention time and fragmentation pattern of the analytes with those of the parent compound. A total of eight metabolites, including seven phase I and one phase II metabolites, were detected and tentatively identified for the first time. Oxidation, deglycosylation and glucuronidation were found to be the major metabolic processes of the compound in rats. In addition, a possible metabolic pathway on the biotransformation of DIS in vivo was proposed. This study provides valuable and new information on the metabolism of DIS, which will be helpful for further understanding its mechanism of action. Copyright © 2015 John Wiley & Sons, Ltd.     

Facile fabrication of fast recyclable and multiple self‐healing epoxy materials through diels‐alder adduct cross‐linker

A reversibly cross‐linked epoxy resin with efficient reprocessing and intrinsic self‐healing was prepared from a diamine Diels‐Alder (DA) adduct cross‐linker and a commercial epoxy oligomer. The newly synthesized diamine cross‐linker, comprising a DA adduct of furan and maleimide moieties, can cure epoxy monomer/oligomer with thermal reversibility. The reversible transition between cross‐linked state and linear architecture endows the cured epoxy with rapid recyclability and repeated healability. The reversibly cross‐linked epoxy fundamentally behaves as typical thermosets at ambient conditions yet can be fast reprocessed at elevated temperature like thermoplastics. As a potential reversible adhesive, the epoxy polymer with adhesive strength values about 3 MPa showed full recovery after repeated fracture‐thermal healing processes. The methodology explored in this contribution provides new insights in modification of conventional engineering plastics as functional materials. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2094–2103