基于三角波瓣混合器的超声速流场精细结构和掺混特性

在超声速吸气式混合层风洞中,采用基于纳米粒子的平面激光散射(NPLS)技术对平板混合层和三角波瓣混合器诱导的混合层流场精细结构进行了对比实验研究.上下两层来流的实测马赫数分别为1.98和2.84,对流马赫数为0.2.NPLS图像清晰地展示了Kelvin-Helmholtz涡、流向涡、波系结构以及大尺度涡结构的配对合并过程.通过对比分析时间相关的NPLS流场图像,发现了大尺度拟序结构随时间发展演化的非定常特性.基于流动显示结果,采用分形维数和间歇因子指标对流场结构和混合特性进行了定量分析.实验研究表明,三角波瓣混合器诱导的流向涡结构显著提高了上下两层来流的掺混效率,其流动远场的分形维数突破了平板混合层中完全湍流区的分形维数值,达到了1.88,流场结构表现出明显的破碎性,有利于流动在标量层面的扩散和掺混.流动间歇性分析表明,流向涡与展向涡的相互剪切作用主导着混合层的掺混特性,同时由于流向涡的卷吸作用,三角波瓣混合器诱导的混合层混合区域更大,更多的流质被卷入混合区完成混合.     

Highly enhanced low-temperature performances of LiFePO<Subscript>4</Subscript>/C cathode materials prepared by polyol route for lithium-ion batteries

Although LiFePO₄/C has been successfully put into practical use in lithium-ion batteries equipped on new energy vehicles, its unsatisfactory low temperature results in poor low performance of lithium-ion batteries, leading to a much smaller continue voyage course at extreme environments with low temperature for electric vehicles. In this paper, the electrochemical performance of the LiFePO₄/C prepared by polyol route was investigated at a temperature range from 25 to ?20 °C. Compared to commercial ones, as-prepared LiFePO₄/C shows a much better low-temperature performance with a reversible capacity of 30 mA h g^?1 even at 5 C under ?20 °C and a capacity retention of 91.1 % after 100 cycles at 0.1 C under 0 °C. Moreover, high-resolution transmission electron microscopy (HRTEM) revealed that this outstanding performance at low temperatures could be assigned to uniform carbon coating and the nano-sized particles with a highly crystalline structure.     

自适应H.264可变块编码模式选择算法

为了减少H.264/AVC帧间编码模式选择的计算复杂度,利用编码模式之间的相关性以及视频序列时空域的相关性,提出了有选择性的小块搜索技术和有选择性的帧内编码模式搜索技术。模拟结果表明,该算法在保持率失真性能的前提下可以大幅度减少模式选择的计算复杂度,有利于H.264的实时应用。     

氧燃烧方式下痕量元素形态转化的试验和模拟研究

结合热重试验及XRF测量,采用化学热平衡分析方法对煤中易挥发的有毒痕量元素砷、铬、锑和汞在不同燃烧方式下的化学形态及分布进行了研究。计算表明,在常规燃烧方式下,痕量元素在400-1800 K的温度范围内容易蒸发,生成气相单质或氧化物。富氧燃烧条件下,高浓度的CO2(g)以及碳颗粒温度的降低在一定程度上会抑制痕量元素的蒸发,同时CO2(g)也会抑制痕量元素向气相次氧化物及单质的转化。     

Y分支器单元的有限差分光束传输法分析

Y分支器是集成光学中一种重要的器件单元。本文使用有限差分光束传输法(FD-BPM)系统地分析了Y分支器的工作机理,包括对称与非对称两种结构,其中着重对非对称Y分支器单元进行了分析,指出其欲完成模式分离所需满足的条件。通过对Y分支器的深入研究,我们也说明了FD-BPM法在对Y分支器及类似器件和单元的模拟分析中所具有的方便性和优越性,这为实际的设计制作工作提供了极好的基础。     

Orthogonal-polarization compensation method for measuring unsteady vertical force of a bumblebee in a wind tunnel

It is important to measure the unsteady vertical force of an insect in a wind tunnel for studying the flight performance of insects. Optical method can measure it with high accuracy, but it is affected by air turbulence. An orthogonal-polarization compensation (OPC) method is developed for measuring the beating force of a bumblebee in a wind tunnel and compensating the error due to beam fluctuations induced by air turbulence. The applicability of the OPC method was confirmed by using a piezo translator to generate the tilt angle variation. The results show that by using the OPC method, the error in tilt angle measurement due to air turbulence can be decreased by about 80% compared with that using the conventional angle measurement method. The OPC method was then applied to measure the tilt angle variation caused by the beating motion of a bumblebee attached to one end of a sensor block in a wind tunnel for a wind velocity of 1.1 ms⁻¹. The results confirmed the effectiveness of this new method.     

无催化纳米氧化锌的制备及其光学性质研究

本文采用无催化剂直接蒸发高纯Zn粉,在800℃氧气氛条件下,在Si(111)衬底上生长得到以四角状为主的纳米ZnO(T-ZnO)。T-ZnO纳米线每个角约互成110°,长度约为1.5μm,直径100nm左右;Raman分析表明E2(H)普遍存在于各形态的ZnO;光致发光光谱表明,T-ZnO纳米线的光致发光除了与材料性质有关,还与杂质缺陷有关,蓝绿光带是ZnO的缺陷产生的。     

非视线紫外光信号传输时间特性的数值模拟

在研究紫外光学非视线通信技术中,需要深入了解由于紫外大气散射效应所带来的各种信号畸变.传统的单次散射近似方法在进行较远距离、复杂天气条件下非视线光传输模拟时误差很大,采用基于Monte Carlo(MC)方法改进算法进行非视线紫外光信号传输的数值模拟,通过随机抽样的方法模拟光子在大气系统中的随机游动,在光子被大气中的粒子散射时计算其进入探测器的概率,模拟大气系统的脉冲响应函数.模拟结果表明:采用光子散射探测概率方法改进后的MC模型在模拟非视线光信号传输时计算效率显著提高;大气系统对非视线传输时的紫外光脉冲具有很强的展宽效应;随着光信号传输距离的增大,信号强度呈近似指数衰减的趋势.     

Characteristics of selective oxidation during the fabrication of vertical cavity surface emitting laser

Taking into account oxidation temperature, N₂ carrier gas flow, and the geometry of the mesa structures this paper investigates the characteristics of selective oxidation during the fabrication of the vertical cavity surface emitting laser (VCSEL) in detail. Results show that the selective oxidation follows a law which differs from any reported in the literature. Below 435℃ selective oxidation of Al_0.98Ga_0.02As follows a linear growth law for the two mesa structures employed in VCSEL. Above 435℃ approximately increasing parabolic growth is found, which is influenced by the geometry of the mesa structures. Theoretical analysis on the difference between the two structures for the initial oxidation has been performed, which demonstrates that the geometry of the mesa structures does influence on the growth rate of oxide at higher temperatures.