Performance improvement of PDMS/PES membrane by adding silicalite-1 nanoparticles: separation of xenon and krypton

The polydimethylsiloxane (PDMS) mixed matrix membrane with dispersed phase of nanozeolite silicalite-1 has been synthesized on polyethersulphone (PES) as a support, and its performance in the gas separation of xenon and krypton has been studied. For this purpose, nanozeolite silicalite-1 is synthesized by the hydrothermal clear solution method and is characterized by XRD and SEM analysis. In this research, the separation performance of MMM has also been compared with the polymeric PDMS membrane. Furthermore, the effect of feed pressure and loading percentage of nanozeolite in the polymeric matrix are evaluated. The results indicate that the addition of nanozeolite to the polymeric matrix improves its separation performance, and that the changes of the feed pressure have no major effect. The average permeability of the krypton and xenon gases through the PDMS polymeric membrane is calculated as 1.25 × 10^?9 and 1.78 × 10^?9 cm mol/(cm² s kPa), respectively, while by adding only 5 wt% of nanosilicalite-1 to the polymeric matrix of the membrane, this amount increased to 1.82 × 10^?9 and 8.07 × 10^?9 cm mol/(cm² s kPa), respectively. In addition, the presence of nanosilicalite-1 as the filler leads to an increase in the selectivity of xenon to krypton up to 4.38.     

Well Oriented ZnO Nanorods Array: Negative Resistance and Optical Switching

Well‐oriented ZnO nanorods (NRs) arrays were grown on Si, alumina, quartz, and FTO substrates through a ZnO seed layer followed by low temperature wet chemical process. The influence of sputtered ZnO seed layer thickness (100, 50, 32, and 16 nm), annealing temperature and CuO_x coverage on the characteristics of ZnO NRs were investigated in this study. The crystalline structural, chemical, morphological, optical, and electrical properties of ZnO NRs arrays were studied by X‐ray diffraction (XRD), field emission‐ scanning electron microscopy equipped by energy dispersive X‐ray spectroscopy (FE‐SEM/EDX), Raman scattering, UV/Vis ‐ near IR absorption spectroscopy and current‐voltage characteristic. XRD and Raman spectra measurement revealed that the synthesize ZnO displayed hexagonal wurtzite structure. The individual rod diameter, density, and orientation can be controlled by varying the seed layer thickness. The mean diameter and maximum length of ZnO NRs are around 55–66 nm and 282 nm, respectively. ZnO NRs/ ZnO thin film structure shows optical switching and negative differential resistance behavior as applicable to ON/OFF gate and memory devices.     

The effect of side-chain length of cellulose fatty acid esters on their thermal,barrier and mechanical properties

Currently, long-chain cellulose esters are not produced commercially because of high price, and since their preparation typically requires a large quantity of chemicals. To reduce the chemical consumption, cellulose reactivity needs to be increased without losing its quality. One way to increase the reactivity of cellulose is to decrease its molar mass in a controlled manner. In this study, we have synthesized cellulose esters with different side-chain length (C6–C18) in a homogeneous system using ozone molar mass-controlled cellulose. The target was to keep the degree of substitution as low as possible while still ensuring the suitability of cellulose esters for solvent casting. Thermal, barrier and mechanical properties were studied depending on cellulose fatty acid ester side-chain length. All our molar mass-controlled cellulose esters form optically transparent, flexible and heat-sealable films with good water barrier properties and are processable without the addition of an external plasticizer. Furthermore, the films have mechanical properties comparable to some generally used plastics. These good properties suggest that our molar mass-controlled cellulose esters could be potential candidates for various applications such as films and composites.     

Improving the mechanical properties of CNF films by NMMO partial dissolution with hot calender activation

Reinforcing of cellulose nanofibril (CNF) films by partial dissolution with N-methylmorpholine-N-oxide (NMMO) was investigated. The method investigated is composed of impregnation of CNF film with liquid solution of NMMO followed by dry heat activation. The heat activation of the impregnated film was carried out using a heated calendering nip, which enabled simultaneous heating and compression. The partial dissolution of cellulose by NMMO caused a significant increase in the transparency of CNF film due to the decrease of film porosity and increased surface smoothness. The dry strength of the reinforced film was increased from 122 up to 195 MPa. Furthermore, the wet strength of the reinforced film was up to 70% greater than the dry strength of pure CNF film. The changes in the fibrillar structure were investigated with topographical imaging (SEM and AFM) and spectroscopically using NMR and FTIR. No significant changes in the fibril structure or cellulose morphology were observed. Moreover, the treated film resisted significant water pressure, highlighting CNF film’s permanent water resistance. The partial dissolution process with NMMO was also capable of reinforcing a CNF composite film with macro scale structural elements (lyocell short-cut fibres). The strategy investigated is a robust and fast method to improve the mechanical properties of fibrillary cellulose films, allowing them utilization in applications where improved water resistance and fully cellulosic character are required properties.     

Surfactant effects on the particle size,zeta potential,and stability of starch nanoparticles and their use in a pH-responsive manner

Storage conditions seem to be important in the long-term stability of nanoparticles (NPs). This work studies the effects of surfactants and storage container on particle size distribution and zeta potential during long-term storage of acid hydrolyzed potato starch NPs. The NPs were prepared from potato starch using acid hydrolysis and high-intensity ultrasonication. During the ultrasonic treatment, the surfactants were added dropwise to the solutions to reduce the size and stabilize the formed NPs. Particle size distribution, zeta potential, and FE-SEM were used to characterize the ensuing NPs. Additionally, a 5-month stability study was performed to evaluate the maintenance of potato starch NPs over time at different storage conditions. Then, NPs from corn starch were produced by the same procedure and were used for preparing pH-responsive nanocarriers containing NaHCO₃ for delivery of an anti-cancer drug, FTY720. These NPs were able to release the drug at pH 5.0 because of CO₂ generated from NaHCO₃ in acidic pH and released from the NPs by the production of pores, which accelerate drug release.     

Extraction of uranium(VI) by tri iso-amyl phosphate (TiAP) in ionic liquids

Batch extraction of uranium(VI) from uranyl nitrate solutions using TiAP in ionic liquids ([BMIM]PF₆ and [HMIM]PF₆) is studied. Effects of acidity, TiAP concentration in ionic liquid and temperature on distribution coefficient are studied. Results show that distribution coefficient increases with an increase in acidity and reduces with an increase in the alkyl chain length of the cation of the ionic liquid. Extraction of uranium(VI) by TiAP-[HMIM]PF₆ system is found to involve two molecules of the extractant per metal ion and extraction is found to change from being exothermic to endothermic as the percentage of the extractant is increased.     

A universal blown film apparatus for <Emphasis Type="Italic">in situ</Emphasis> X-ray measurements

A setup of blown film machine combined with in situ synchrotron radiation X-ray diffraction measurements and infrared temperature testing is reported to study the structure evolution of polymers during film blowing. Two homemade auto-lifters are constructed and placed under the blown machine at each end of the beamline platform which move up and down with a speed of 0.05 mm/s bearing the 200 kg weight machine. Therefore, structure development and temperature changes as a function of position on the film bubble can be obtained. The blown film machine is customized to be conveniently installed with precise servo motors and can adjust the processing parameters in a wide range. Meanwhile, the air ring has been redesigned in order to track the structure information of the film bubble immediately after the melt being extruded out from the die exit. Polyethylene (PE) is selected as a model system to verify the feasibility of the apparatus and the in situ experimental techniques. Combining structure information provided by the WAXD and SAXS and the actual temperature obtained from the infrared probe, a full roadmap of structure development during film blowing is constructed and it is helpful to explore the molecular mechanism of structure evolution behind the film blowing processing, which is expected to lead to a better understanding of the physics in polymer processing.