考虑结合部特征的?150 mm口径反射镜模型修正

针对?150 mm口径反射镜受结合部的非线性因素影响导致结构分析模型精度较差的问题,提出了线性的动力学等效建模与参数修正方法。首先,在实际装配和约束环境下测试并获得了反射镜结构的试验模态参数。然后,根据界面结合部的动力学特征,对反射镜结构按照镜框固定连接模型、镜面螺钉夹持模型以及间隙等效模型进行了等效建模。最后,以试验模态参数为修正目标,采用优化方法对反射镜结构的动力学等效模型进行了参数修正,并采用模型分层和分步修正的思路,依据结合部特征将修正模型细分为两部分,提高模型参数的修正效率。结果表明,参数修正后的固有频率平均误差为1.5%,模态置信度均大于0.8,提升了反射镜结构的动力学模型精度,验证了线性化等效建模方法的正确性。     

N掺杂对α-石墨炔表面吸附H_2O,H,O和OH的电子性质和磁性的影响

石墨炔是一种新型的二维(2D)碳的同素异形体,炔键单元的高活性使其在小分子吸附方面相比石墨烯更具优势.本文基于密度泛函理论(DFT),研究了H_2O和H、O及OH分别在原始的和掺杂了N原子的α-石墨炔上的相互作用.研究结果表明,N掺杂和小分子吸附能够改变α-石墨炔的电子结构和磁性. N原子掺杂后α-石墨炔对小分子的吸附能力明显增强. H、O原子和OH吸附在N原子掺杂体系前后表现出明显的磁性差异:H原子和OH吸附在纯净的α-石墨炔上体系显示磁性,N原子掺杂后,磁性消失;而O原子则是吸附在纯净的α-石墨炔上未表现出磁性,N原子掺杂后,体系出现磁性.此外,α-石墨炔对水分子的吸附作用较弱,受范德瓦耳斯作用影响较大,属于物理吸附.本研究将为α-石墨炔中N杂质检测以及α-石墨炔基气体传感器的设计研究提供新的思路.     

近代物理讲座 第八讲 恒星的形成、演化和终局

同其它物体一样,恒星也有它的发生、发展和死亡的过程．只是这个过程相当缓慢．一颗类似太阳的恒星,它一旦形成,将在约１０～（１０）年的时间内不会有显著的变化．当然,这和人类文明史（约１０～３－１０～４年）相比,太长了．因此人们不可能直接观测到恒星的演变．但是,他们可以对大量处于不同年龄和不同演化阶段的恒星进行观察,并对大量资料作出科学的统计分析．这方面极重要的贡献是在本世纪初由Ｈｅｒｔｚｓｐｒ－?...     

多联式空调制冷工况动态特性仿真研究

基于多联式空调系统状态空间法模型,对一套四个室内机和一台室外机的多联机在制冷模式下的动态特性进行了仿真研究。分析了室内外温度、室内外机风量、压缩机频率和电子膨胀阀开度等参数的变化对系统运行状态参数(如蒸发温度、冷凝温度、压缩机排气温度、过冷度、过热度)的动态变化的影响规律。为制定和优化多联机控制系统的控制策略和控制算法提供了有效的依据。     

R600a喷雾冷却系统换热过程

以R600a压力式封闭系统喷雾冷却过程为研究对象,对其换热过程进行分析。对液滴撞击热面后的状态进行建模,分析了其运动状态。通过忽略液膜的对流换热,引入韦伯数来简化并修正雾滴与热源表面的对流换热系数关联式;借鉴二次成核理论,通过单位时间内,单位面积上覆盖的雾滴数量对核态沸腾换热系数关联式修正。通过上述分析,以对流换热和核态沸腾换热两种机理为中心,建立了新的换热系数关联式。通过与其他文献的关联式、实验测量值进行比较、不同工质进行比较、不同实验系统比较,发现该式预测值和实验测量值偏差在±20%以内,能够很好地预测压力式封闭系统喷雾冷却过程的换热系数。     

Adaptive multitrack reconstruction for particle trajectories based on fuzzy c-regression models

In this paper, an approach to straight and circle track reconstruction is presented, which is suitable for particle trajectories in an homogenous magnetic field (or 0 T) or Cherenkov rings. The method is based on fuzzy c-regression models, where the number of the models stands for the track number. The approximate number of tracks and a rough evaluation of the track parameters given by Hough transform are used to initiate the fuzzy c-regression models. The technique effectively represents a merger between track candidates finding and parameters fitting. The performance of this approach is tested by some simulated data under various scenarios. Results show that this technique is robust and could provide very accurate results efficiently.     

Ultra-longer fiber cantilever taper for simultaneous measurement of temperature and relative humidity

An ultra-longer fiber cantilever taper for simultaneous measurement of the temperature and relative humidity (RH) with high sensitivities was proposed. The structure was fabricated by using the simple and cost-effective method only including fiber cleaving, splicing, and tapering. The length of the cantilever taper is about 1.5 mm. The dip A and dip B were measured simultaneously, owing to the ultra-long length and super-fine size, the temperature sensitivities of the dip A and dip B reached as high as 127.3 pm/℃ and 0 pm/℃ between 25 ℃ and 50 ℃, and the RH sensitivities are -31.2 pm/% RH and -29.2 pm/% RH with a broad RH interval ranging from 20% RH to 70% RH. Besides, the proposed structure showed good linearity in the sensing process and small temperature crosstalk. It will be found in wide applications in environmental monitoring, food processing, and industries.