采用四分之一波长谐振器的P波段高温超导滤波器研制

本文采用四分之一波长螺旋型谐振器设计并制作了6节P波段高温超导滤波器.谐振器一端开路,另一端与接地块连接实现短路.接地块与封装盒的盒壁之间通过点焊硅铝丝进行连接.通过电磁场仿真分析了硅铝丝的数量对滤波器性能的影响.滤波器未经调谐的测试结果与仿真结果符合得很好,其通带内最小插损仅为0.07dB,反射损耗优于17.9dB,且第一个寄生通带位于基频中心频率的三倍处.表明通过硅铝丝点焊实现接地的方法对滤波器性能的影响很小,且采用四分之一波长谐振器可以有效抑制二倍频.     

Nano-Crystalline Diamond Films with Pineapple-Like Morphology Grown by the DC Arcjet vapor Deposition Method

A nano-crystlline diamond film is grown by the dc arcjet chemical vapor deposition method. The film is characterized by scanning electron microscopy, high-resolution transmission electron microscopy （HRTEM）, x-ray diffraction （XRD） and Ftaman spectra, respectively. The nanocrystalline grains are averagely with 80hm in the size measured by XRD, and further proven by Raman and HRTEM. The observed novel morphology of the growth surface, pineapple-like morphology, is constructed by cubo-octahedral growth zones with a smooth faceted top surface and coarse side surfaces. The as-grown film possesses （100） dominant surface containing a little amorphous sp2 component, which is far different from the nano-crystalline film with the usual cauliflower-like morphology.     

质子数Z 分别位于Ru 之上和之下的A~(100~126) 丰中子原子核三轴形变在原子核形状变迁和共存中的重要作用(英文)

基于Ru (Z = 44) 丰中子同位素中存在最大三轴形变的理论预言和实验证据,综述了近年来Rh (Z = 45),Pd (Z =46), Ag (Z =47), Cd (Z =48)(质子数Z 位于Ru,Z =44 之上)及Zr (Z =40), Nb (Z =41), Mo (Z =42),Tc (Z =43)(质子数Z 位于Ru,Z =44 之下) 的A~ (100~126) 丰中子同位素中关于三轴形变的形状变迁和形状共存系统性研究的重要进展。252Cf 自发裂变瞬发 射线-- 三重符合、特别是新建立的--- 四重符合数据的系统观测和研究,在Ru, Pd, Cd 和Nb 丰中子同位素中显著扩展或首次观测到了一系列能带,为这个核区原子核形状的研究提供了新的、重要的实验数据。联系此前报道的有关进展,使用PES, TRS, PSM, CCCSM 和SCTAC 理论模型计算拟合新的实验数据,在该核区沿同中素和同位素链,并随自旋和激发能变化各自由度,跟踪原子核形状渐进变化,获得了新的系统性研究成果,显著扩展和深化了人们对原子核形状变迁和形状共存的认知。对于Ru 及其上的Rh (Z = 45), Pd (Z = 46), Ag (Z = 47) 和Cd (Z = 48) 丰中子同位素的研究表明:Rh 丰中子核具有比最大值稍小的三轴形变,γ = 28°,并在103{106Rh 同位素链上鉴别出了手征对称破缺;在三轴形变核112Ru和114Pd(N = 68)中发现了三轴原子核的摆动运动,该摆动运动也可能在114Ru (N = 70)中存在;观察到了从具有最大三轴形变的110,112Ru 中手征破缺到稍小三轴形变的112,114,116Pd 中扰动的手征破缺的过渡;在较软的Ag 核中观察到了丰富的谱学结构,在104,105Ag 中鉴别出了可能的手征对称破缺,在较重的115,117Ag 中提出了趋于三轴形变的软度;具有小形变的Cd核的能级结构被解释为准粒子耦合、准转动和软三轴形变;最近的库伦激发的研究提供了Z = 50, N = 82满壳附近122,124,126Cd 核中出现核集体性的实验和理论证据;上述研究成果展现出从Ru中的最大三轴形变(γ=30°,三轴形变极小增益为0.67 MeV), 经具有大三轴形变的Rh核γ=28°),到Pd核中的稍小、但稳定于中等自旋到高自旋区的三轴形变(γ~41°,三轴形变极小增益为0.32 MeV),再经Ag核中的软度,最后到具有很小形变、但仍出现集体性质、包括软三轴形变的Cd核的过渡。对于Pd核转动带交叉系统性的研究揭示了其第一带交叉(νh_11/2)2 中子转动顺排的上行驱动,和第二带交叉(πg_9/2)2质子转动顺排的下行驱动效应,成功地解释了114Pd 中的三轴摆动运动,并给出了110-118Pd同位素链中理论早已预言、而比早期理论预言更为完整准确的形状渐进变迁和形状共存的图像。根据该核区的系统研究,发现最大三轴形变出现在112Ru,而在相邻的偶Z(Pd)同位素链,三轴形变极小的中心在114Pd, 两者均为N = 68。上述系统性研究沿相邻的Ru和Pd偶Z同位素链,在N =68同中素中鉴别出最大三轴形变,均比理论预言的108Ru 和110Pd 多4个中子。在Z值位于Ru (Z = 44) 之下的Zr (Z = 40), Nb (Z = 41), Mo (Z = 42) and Tc (Z = 43) 丰中子同位素中,Y和Zr核具有很强的轴对称四极形变,而在较重的Zr同位素中出现了自由度;较重的Nb核(A = 104~106) 基态具有中等程度的软三轴形变和强四极形变,随着自旋和激发能的增加,过渡到接近于轴对称的强四极形变;而较轻的Nb核(A≤103) 基态均接近轴对称形状;在Nb同位素链上基态由球形到强四极形变的形状突变发生在100Nb(N = 59),在100-106Nb同位素链中基态的软三轴形变随中子数增加而增加;在Nb核中还观察到关于软三轴形变的形状共存;Mo核具有大的三轴形变,观察到了振动和手征对称破缺;Tc核具有比最大值稍小的三轴形变,γ=26°,并观察到了手征对称破缺。质子数Z从41到48的A~(100~126)丰中子同位素,特别是Pd和Nb 同位素,呈现出关于三轴形变的过渡特征。This paper reviews the systematic investigations and understanding for the shape transitions and coexistence with regard to triaxial deformations in A s 100 to 126 neutron-rich Rh (Z = 45), Pd (Z = 46), Ag (Z = 47), Cd (Z = 48) and Zr (Z = 40), Nb (Z = 41), Mo (Z = 42), Tc (Z = 43) isotopes with Z beyond and below Ru (Z = 44), respectively, in Ru the maximal triaxial deformation having been predicted and deduced. The recent measurements and studies of prompt triple- and four-fold, γ-γ-γ and γ-γ-γ-γ, coincidence data from the spontaneous fission of 252Cf using Gammasphere have yielded considerable expansion and extension or first observation of the bands in Ru, Pd, Cd, and Nb isotopes,which provided important data for the studies of nuclear shapes in this region. Combined with previous investigations, recent systematic studies of the new data well reproduced by PES, TRS, PSM, CCCSM and SCTAC model calculations have traced shape changes along the isotonic and isotopic chains, respectively,and with changing excitations/spins as well, significantly expanding our knowledge of shape transitions/coexistence in nuclei.For the neutron-rich Ru and beyond, Rh, Pd, Ag and Cd isotopes, triaxial deformations γ= 28°,slightly smaller than the maximal value, were deduced in Rh (Z = 45) isotopes, with chiral symmetry breaking proposed in 103-106Rh; onset of wobbling motions were identified in 112Ru and 114Pd (N =68),and probably also in 114Ru (N =70); evolution from chiral symmetry breaking in 110,112Ru with maximal triaxial deformations to disturbed chirality in 112,114,116Pd with less pronounced triaxial deformations was proposed; rich nuclear structure was proposed in soft Ag isotopes with possible chiral doubling structure suggested in 104,105Ag, and softness towards triaxial deformation proposed in heavier 115,117Ag;quasi-particle couplings, quasi-rotations and soft triaxiality were suggested in Cd (Z =48) isotopes with small deformations; onset of collectivity was recently suggested in 122,124,126Cd in the vicinity of Z =50 and N = 82 closed shells by studies of Coulomb excitations; shape evolutions from maximal triaxial deformations in Ru (γ=30°, with triaxial minimum energy gain of 0.67 MeV), through Rh with large triaxial deformations ( γ=28°), to less pronounced triaxiality in Pd (with triaxial minimum energy gain of 0.32 MeV), then soft triaxiality in Ag, and finally to slightly deformed Cd isotopes but with emergence of collectivity and soft triaxiality were proposed. The systematic studies of the band crossings in Pd revealed up-rising drivings of the first band crossings caused by (νh_11/2)2 and down-sloping drivings of the second band crossings by (πg_9/2)2, explained the onset of wobbling motions in 114Pd,and showed a long-sought picture of shape evolution and coexistence in the Pd isotopic chain which is more complete but complex than earlier predictions. Based on the systematic studies in the mass region,maximal triaxial deformation is found to be reached in 112Ru and less-pronounced triaxiality centered at 114Pd, both for N =68, four neutrons more than predicted in earlier theoretical calculations.In the neutron-rich Zr (Z =40), Nb (Z =41), Mo (Z =42) and Tc (Z =43) isotopes with Z just below Ru, large quadrupole deformations of axially symmetric shapes were deduced in Y and Zr isotopes, with emergence of the degree of freedom having been suggested for heavier Zr isotopes; medium triaxial deformations were deduced for the ground states of heavier (A > 104) Nb isotopes, and, with increasing excitations and spins, evolution from medium triaxial deformations with strong quadrupole deformations at ground states to nearly axially-symmetric shapes were deduced; light Nb isotopes (A6103) have near axially-symmetric shapes with strong quadrupole deformations; combining with the identification of onset of strong quadrupole deformation at 100Nb in the Nb isotopic chain, an increase of soft triaxiality with increasing neutron number was proposed in 100-106Nb. Shape coexistence with regard to soft triaxiality is also proposed in Nb isotopes; large triaxial deformations, vibrations and chiral doublets were proposed in Mo isotopes; chiral doubling and large triaxial deformations (γ ~26°) slightly smaller than the maximal triaxiality were suggested in Tc isotopes.The neutron-rich nuclei with Z ranging from 41 through 48 and A ~100 to 126, especially the Pd and Nb isotopes are thus found to be transitional nuclei with regard to triaxiality.     

浅析模具产品设计技术应用和发展趋势

随着经济全球化及市场竞争的日益激烈,模具产品设计正面临严峻考验。模具企业必须利用最新的技术,在最短的时间内开发出高质量、低成本、高附加值的产品,以最快的速度响应和投放市场。这就需要改变传统模具产品设计方式,从而做出正确的决策与设计方案。     

一类本原图的Scrambling指数

文章主要研究了一类特殊的含有6个圈3个不同圈长的本原有向图的Scrambling指数,通过分析每一点经过t长途径可到达的点的集合,给出了此类图的Scrambling指数.     

New Voronoi Diagram Algorithm of Multiply-Connected Planar Areas in the Selective Laser Melting

This paper studies the practical generation of Voronoi diagrams for multiply-connected planar areas bounded by line segments. The core of the algorithm was calculating Voronoi polygon of every Voronoi object in planar areas independently. The main approach had two steps. The first step was calculating all relevant bisectors of every Voronoi object. The second was combining obtained bisectors into completed Voronoi polygons individually. All code was implemented in Visual C++ platform. The resulting code was extensively tested in real-world data and its practical running time grew only linearly. Three statistical CPU-consumption charts had been drawn with the Voronoi diagrams computation data, and compared with other published codes for computing Voronoi diagrams. The algorithm was applied to compute offsetting of slice area consisting of large-scale line segments for the selective laser melting (SLM) trajectory scanning technology which is a kind of rapid prototyping (RP). The experimental results of offsetting for slice area based on Voronoi diagrams show that the approach is effective and simple for polygon offsetting problems. The method is helpful to those offsetting work and can provide more effective offsetting solution.     

12脉串联整流装置的谐波量化分析

本文以应用于轧钢行业的12脉串联整流装置为研究对象,分析其产生的谐波特点,量化探讨整流桥的触发角和交流侧电感引起的重叠角对谐波电流的影响,并通过simulink进行仿真,仿真分析结果对轧钢企业选配适合的触发角、适合的交流侧电抗有一定的指导作用。     

FTTH(光纤入户)技术特点及应用模式探讨

随着Internet宽带应用的日益发展和普及,宽带接入技术不断推陈出新,人们对接入带宽需求的不断提高,催生光纤到户(FTTH)接入技术的发展和应用。本文在简述FTTH技术概念、特点的基础上,对比了主流PON技术标准的优缺点,详细介绍了FTTH的组网结构,并深入探讨FTTH在三网融合中的基础作用。     

无线POCSAG编码的接收与解码方法研究

介绍无线寻呼接收器UAA2080的性能，分析无线寻呼POCSAG协议，在此基础上，给出了利用通用单片机实现POCSAG数据流的接收和解码方法。