Charge transport in a mixed ionically/electronically conducting, cationic, polyacetylene ionomer between ion-blocking electrodes

The electrical behavior of the cationic, polyacetylene-based, conjugated ionomer, poly[(2-cyclooctatetraenylethyl)trimethylammonium trifluoromethanesulfonate], sandwiched between gold electrodes is reported. The steady-state current of this mixed ionically/electronically conducting system is assigned to be unipolar diffusive hole transport for voltages below approximately 1.4 V, giving way to bipolar migratory transport above approximately 1.4 V. In the low-voltage regime, a non-Faradaically controlled doping model is proposed where p-doping at the anode is balanced by the charging of an ionic double layer at the cathode. In the high-voltage regime, n- and p-type regions extend from the electrodes as the voltage becomes sufficient to drive disproportionation and the electric field required by the redistribution of ions begins to substantially influence carrier transport. The assignment of a transport mechanism is primarily based on analyzing the decay of the steady-state system under short-circuit and open-circuit conditions. First, it is shown that the power describing the power-law decay of the short-circuit current is characteristic of the steady-state carrier profile. Second, it is argued that a component of the time-dependent, open-circuit voltage decaying more rapidly than the time scale for ion motion is indicative of a substantial migratory component to steady-state transport, as observed in the high-voltage regime. The hole and electron mobilities are estimated to be on the order of 10(-7)-10(-6) cm(2) V(-1) s(-1).     

On-line concentration of s-triazine herbicides in micellar electrokinetic chromatography using a cationic surfactant

A new method for the simultaneous determination of anions (sulfate, nitrate, and chloride) and cations (sodium, ammonium, potassium, magnesium, and calcium) in acid rain waters was investigated using high-performance ion-exclusion/cation-exchange chromatography with conductimetric detection on a separation column packed with a polymethacrylate-based weakly acidic cation-exchange resin in the hydrogen-form and an eluent comprising 1.5 mM sulfosalicylic acid–6 mM 18-crown-6 at pH 2.6, operated at 1.5 ml/min. Effective separation and highly sensitive conductimetric detection for the anions and the cations was achieved in about 14 min. Since the ionic balance (equivalents of anions/equivalents of cations) of acid rain waters of different pH (4.40–4.67) ranged from 0.97 to 0.94, evaluation of the water quality of acid rain was possible. This method was successfully applied to the simultaneous determination of the anions and the cations in acid rain transported from mainland China and North Korea to central Japan monitored by a meteorological satellite data analyzer.     

On the surface modification of microchannels for microcapillary electrophoresis chips

This paper presents systematic investigation of the microchannel surface properties in microCE chips. Three popular materials for microCE chips, polydimethylsiloxane (PDMS), quartz, and glass, are used. The zeta potentials of these microchannels are calculated by measuring the EOF velocity to evaluate the surface properties after surface modification. The hydrophobic PDMS is usually plasma-treated for microCE applications. In this study, a new method using a high-throughput atmospheric plasma generator is adopted to treat the PDMS surface under atmospheric conditions. In this approach, the cost and time for surface treatment can be significantly reduced compared with the conventional vacuum plasma generator method. Experimental results indicate that new functional groups could be formed on the PDMS surface after treatment, resulting in a change in the surface property. The time-dependent surface property of the plasma-treated PDMS is then measured in terms of the zeta potential. Results show that the surface property will reach a stable condition after 1 h of plasma treatment. For glass CE chips, two new methods for changing the microchannel surface properties are developed. Instead of using complicated and time-consuming chemical silanization procedures for CE channel surface modification, two simple and reliable methods utilizing organic-based spin-on-glass and water-soluble acrylic resin are reported. The proposed method provides a fast batch process for controlling the surface properties of glass-based CE channels. The proposed methods are evaluated using PhiX-174 DNA maker separation. The experimental data show that the surface property is modified and separation efficiency greatly improved. In addition, the long-term stability of both coatings is verified in this study. The methods proposed in this study show potential as an excellent solution for glass-based microCE chip surface modification.     

Characterization of polyethylene glycol-modified proteins by semi-aqueous capillary electrophoresis

A new program to characterize polyethylene glycol-modified (PEGylated) proteins is outlined using capillary zone electrophoresis (CZE). PEGylated ribonuclease A and lysozyme were selected as examples. Five separation procedures were compared to select out the mixed buffer of acetonitrile-water (1:1, v/v) at pH 2.5 as the best to characterize the PEGylated proteins without sample pretreatment. Polyethylene oxide (PEO) with a high molecular mass of 8 x 10(6) was applied to rinse the capillary to form a dynamic coating which would decrease the undesirable proteins adsorbed to the inner wall of the silica. The electroosmotic flow (EOF) mobility of the five procedures was determined, respectively. It is found that acetonitrile is mainly responsible for the good resolution of PEGylated proteins with the help of PEO coating in the semi-aqueous system. The low EOF mobility and current in the semi-aqueous system might also have some responsibility for the high resolution. The semi-aqueous procedure described in this paper also demonstrates higher resolution of natural proteins than aqueous ones.     

Experimental studies on interaction of water mist with class K fires

Interaction of water mist with cooking oil fires is studied experimentally and theoretically. A LDV/APV system is used to measure the velocity and diameter of water mist at different pressures in the experiments,and the effect of water mist velocity and diameter on fire extinguishment efficiency is investi-gated. The experimental results show that water mist has excellent surface cooling effect; it can control and extinguish cooking oil fires quickly without re-ignition. The critical temperature (Tfo) is calculated by energy balance equation,and the fire plume momentum is calculated and compared with that of water mist in order to determine the critical velocity (νwy) of fire extinguishment. This paper provides references for cooking oil fires extinguishment with water mist.     

Study and Application of Internal Coating Technique to Drag Reduction of the Trunk Pipeline for the West-East Gas Pipeline

Coverage layer coated in the internal wall of pipeline enables the friction drag to be reduced, the throughput and the gas transmission efficiency to be increased, the frequency of pigging and the number of the intermediate compressor station to be reduced, and the power consumption of the compressor to be decreased etc. The drag reduction is a high advanced scientific technique with outstanding economical benefit. The study and application of internal coating technique for drag reduction of 4000km trunk pipeline in West-East gas transmission pipeline (WEGTP) project are described, in which the main points are the drag reduction principle, coating process and the indoor study of this technique with own-decided knowledge property right at home.     

Leaching behavior of V,Pb, Cd,Cr, and As from stone coal waste rock with different particle sizes

This paper investigates the leaching behavior of heavy metals (V, Pb, Cd, Cr, and As) from stone coal waste rocks with various particle sizes using dynamic leaching experiments. The results show that the dissolved concentrations of V and As initially increased and then slightly decreased as time progressed and that the dissolved concentrations of Pb, Cd, and Cr were high in the early stage before decreasing. The particle size of the stone coal waste rocks strongly influenced the heavy metal concentration in the leaching solutions. The effects of the particle size of the stone coal waste rocks on the dissolved concentrations of V, Pb, and As decreased in the order fine fraction > medium fraction > coarse fraction, and the effects of particle size on the dissolved concentrations of Cr and Cd decreased in the order medium fraction > coarse fraction > fine fraction and coarse fraction > medium fraction > fine fraction, respectively. The quantities of heavy metals dissolved from the stone coal waste rock with fine particle sizes were observed to decrease in the order V (17104.36 μg/kg) > As (609.41 μg/kg) > Pb (469.24 μg/kg) > Cr (56.35 μg/kg) > Cd (27.52 μg/kg), and the dissolution rates decreased in the order As (2.96%) > Pb (0.93%) > V (0.35%) > Cd (0.25%) > Cr (0.01%). The specific surface area, pore size of the stone coal waste rocks, and chemical forms of heavy metals also influenced the release of heavy metals from the stone coal waste rocks. Kinetic analysis showed that the dissolution of heavy metals fundamentally agreed with the rate equation controlled by the shrinking core model. The results of this study are expected to serve as a reference for the evaluation of heavy metals contamination from stone coal waste rocks.     

Surface modification of Ti-45Al-8.5 Nb alloys by microarc oxidation to improve high-temperature oxidation resistance

Microarc oxidation(MAO)electrolysis plasma deposition was used to prepare Al_2O_3coatings on Ti-45Al-8.5 Nb alloys to improve high temperature oxidation resistance.The surface and cross-section morphologies before and after high-temperature oxidation,the chemical composition,and the phase identification of the coatings were investigated by scanning electron microscopy(SEM),electron probe microanalyses(EPMA),and X-ray diffraction(XRD).The results show that Al_2O_3coatings with a thickness of approximately 8μm can be obtained on the Ti-45Al-8.5 Nb alloys by MAO for 600 s.The samples with the Al_2O_3coatings exhibited better high-temperature oxidation resistance.A minimal weight gain of only 0.396 g/m~2after 100 h oxidation at 900°C was observed for the coatings formed with a deposition voltage of 400 V and using a duty cycle of 3%.The deposition mechanism of the Al_2O_3coatings and the effect of the MAO parameters are also described.     

Design and fabrication of 1-D semiconductor nanomaterials for high-performance photovoltaics

To date, the cost-effective utilization of solar energy by photovoltaics for large-scale deployment remains challenging. Further cost minimization and efficiency maximization, through reduction of material consumption, simplification of device fabrication as well as optimization of device structure and geometry, are required. The usage of 1D nanomaterials is attractive due to the outstanding light coupling effect, the ease of fabrication, and integration with one-dimensional(1-D) semiconductor materials. The light absorption efficiency can be enhanced significantly, and the corresponding light-toelectricity conversion efficiency can be as high as their bulk counterparts. Also, the amount of active materials used can be reduced. This review summarizes the recent development of 1-D nanomaterials for photovoltaic applications, including the anti-reflection, the light absorption,the minority diffusion, and the semiconductor junction properties. With solid progress and prospect shown in the past 10 years, 1-D semiconductor nanomaterials are attractive and promising for the realization of high-efficiency and low-cost solar cells.     

Fast Li+ migration in LiPON electrolytes doped by multi-valent Fe ions

Achieving superior ionic conductivity of Li PON solid electrolyte films is critical for the solid-state thinfilm batteries with high energy density. Here we describe a method of preparing Li PON with promising ionic migration capability and high work function by systematically tailoring the concentration of Fe ions doping. Fe-doped LiPON exhibits excellent ionic conductivity(1.08 × 10^-5S cm^-1, nearly 10 times higher than the pristine LiPON), low ionic activation energy, and...