Effect of Fog and Clouds on the Image Quality in Millimeter Communications

The effect of fog and clouds in millimeter communication is discussed, and the attenuation caused by fog and clouds is reviewed. Signal-to-noise ratio (SNR) of image is derived using relating models of fog and clouds attenuation. According to the relation of image quality and its signal-to-noise ratio, the system behavior is forecasted theoretically. It is shown that the signal-to-noise ratio of receiver at certain transmitter power is inverse with radio wave frequency, from about 70dB at 10GHz to 48dB for fog and 49dB for clouds. The image quality of received signal at certain transmitter power is inverse with radio wave frequency, from about 7 grade at 10GHz to 5.27 grade for fog and 5.37 grade for clouds. The above calculated results are consistent with experimental results.     

热作模具钢表面激光堆焊耐磨合金层的研究

本文主要通过在H13钢上用大功率CO_2激光束进行堆焊,阐述了激光堆焊工艺变化对堆焊组织和性能的影响,在本试验条件下,得到了高密度弥散金属化合物组织的激光堆焊层,平均硬度为HV800,与基体呈冶金结合,耐磨性比H13模具钢提高149%。     

氢化丁苯共聚物结构的核磁共振波谱表征Ⅱ.微观结构的定量计算

在氢化丁苯共聚物¹³C-NMR谱脂肪碳部分谱带归属的基础上,根据各谱带的主要来源,推导出六个二单元浓度的计算公式。计算出二单元、一单元的相对含量,各结构单元的数均序列长度、嵌段含量和其它结构参数。加氢前后的¹H-和¹³C-NMR谱的组成计算结果基本一致。初步探讨了作为粘度指数改进剂的氢化丁苯共聚物微观结构与性能的关系,为合成提供了依据。     

双波长稳频CO_2激光模糊控制系统的建模与优化

报导一种模糊逻辑控制系统的建模与优化方法。以此方法设计的模糊逻辑控制器，用于双波长稳频ＣＯ２激光器的控制得到令人满意的结果。     

Storage performance-metrics and benchmarks

The metrics and benchmarks used in storage performance evaluation are discussed. The technology trends taking place in storage systems, such as disk and tape evolution, disk arrays, and solid-state disks, are highlighted. The current popular I/O benchmarks are then described, reviewed, and run on three systems: a DECstation 5000/200 running the Sprite Operating System, a SPARCstation 1+ running SunOS, and an HP Series 700 (Model 730) running HP-UX. Two approaches to storage benchmarks-LADDIS and a self-scaling benchmark with predicted performance-are also described     

离子注入中污染的产生及防护

本文概述了离子注入过程中污染产生的原因和防止污染的措施，特别强调了对微粒污染和金属污染的防护以满足ＵＬＳＩ加工对离子注入的要求。     

Normal-incidence InAs self-assembled quantum-dot infrared photodetectors with a high detectivity

An InAs/AlGaAs quantum-dot infrared photodetector based on bound-to-bound intraband transitions in undoped InAs quantum dots is reported. AlGaAs blocking layers were employed to achieve low dark current. The photoresponse peaked at 6.2 /spl mu/m. At 77 K and -0.7 V bias, the responsivity was 14 mA/W and the detectivity, D*, was 10/sup 10/ cm/spl middot/Hz/sup 1/2//W.     

High-frequency small signal AC and noise modeling of MOSFETs for RFIC design

High-frequency (HF) AC and noise modeling of MOSFETs for radio frequency (RF) integrated circuit (IC) design is discussed. A subcircuit RF model incorporating the HF effects of parasitics is presented. This model is compared with the measured data for both y parameter and f_T characteristics. Good model accuracy is achieved against measurements for a 0.25 μm RF CMOS technology. The HF noise predictivity of the model is also examined with measured data. Furthermore, a methodology to extract the channel thermal noise of MOSFETs from HF noise measurements is presented. By using the extracted channel thermal noise, any thermal noise models can be verified directly. Several noise models including the RF model discussed in this paper have been examined, and the results show that the RF model can predict the channel thermal noise better than the other models     

A new image coding algorithm using variable-rate side-matchfinite-state vector quantization

A new side-match vector quantizer, NewSMVQ, is presented in this paper. Three techniques are incorporated to improve the image quality, encoding speed, and bit rate for compressing images. The experimental result shows: i) the encoding time of NewSMVQ is almost 7 times faster than that of SMVQ (ordinary fixed-rate side-match vector quantizer) and CSMVQ (variable-rate SMVQ) and ii) NewSMVQ outperforms SMVQ and CSMVQ in terms of bit rate versus image quality tradeoffs.     

玻璃陶瓷材料中Tm3+离子红外到蓝色上转换发光

系统研究了PbF2+GeO2+WO3ⅩⅣTmF3玻璃陶瓷材料中,在近红外光(1.06μm)激发下,Tm3+离子的发光特性.实验中观测到Tm3+离子的两组峰值位置分别在20920cm-1和22173cm-1的蓝色上转换发光,并证实这两组上转换发光分别与吸收三个和四个光子有关,同时建立了上转换发光的模型.为了选择最佳掺杂浓度,详细地测量了Tm3+离子峰值为20920cm-1的蓝色上转换发光强度与TmF3浓度的关系.