平面分拆的矢量控制方法：列严格梯形平面分拆

作为移位平面分拆的自然拓广,本文引入了梯形平面分拆的概念.应用矢量控制技巧,建立了给定形状和行(列)分部约束的列严格梯形平面分拆集合之枚举函数的初等对称函数行列式表达式.其中之一的重要特例构成了关于循环对称平面分拆的Macdonald猜想的证明基础.     

Commuting and stable feedback design for switched linear systems

In the paper, commuting and stable feedback design for switched linear systems is investigated. This problem is formulated as to build up suitable state feedback controller for each subsystem such that the closed-loop systems are not only asymptotically stable but also commuting each other. A new concept, common admissible eigenvector set (CAES), is introduced to establish necessary/sufficient conditions for commuting and stable feedback controllers. For second-order systems, a necessary and sufficient condition is established. Moreover, a parametrization of the CAES is also obtained. The motivation comes from stabilization of switched linear systems which consist of a family of LTI systems and a switching law specifying the switching between them, where if all the subsystems are stable and commuting each other, then the total system is stable under arbitrary switching.     

不连续不可逆二维映象的动力学特性

总结两个保守映象不可逆地分段连续链接(称为类耗散系统)以及一个保守映象与一个耗散映象不可逆地分段连续链接(称为半耗散系统)情况下得到的五项共同动力学特征：不连续边界象集构成的随机网成为唯一的混沌轨道；由于某些相点具有两个逆象而导致的相空间塌缩(类耗散)；由于系统的不连续不可逆性质而出现的胖分形禁区网；在具有吸引子共存时占据不连续边界象集随机网和胖分形禁区网区域的点滴状吸引域以及由此导致的吸引子不可预言性；即使在传统强耗散存在的情况下点滴状吸引域仍由类耗散机制主宰.以一个累积-触发电路为例，说明这五项系统动 关键词： 随机网 禁区网 点滴状吸引域     

基于DSP+CPLD的高精度信号发生器

介绍了基于直接数字式频率合成(DDS)原理的全数字信号发生器(DSP),利用DSP芯片快速、高精度的运算优势以及CPLD芯片灵活的编程逻辑、大容量存储功能的特点,采用通用可编程芯片以及数字波形合成技术,形成高稳定、高精度、高动态的数字合成信号.该信号发生器可产生0～25 kHz的正弦波、三角波和方波,输出电压峰峰值为0～5 V,频率步进1 Hz,幅度步进0.001 V.     

基于PCI总线的高速多路数据传输卡设计

介绍了一套基于外部设备互连(PCI)总线的高速多路数据传输卡的设计,采用基于PCI内核与PCI用户逻辑相结合的新型设计方案,在顶层通过仿真来验证PCI接口以及用户逻辑设计正确与否.降低了设计的复杂程度,提高了电路的集成度和系统的性能,并根据PCI卡对外部设备驱动能力较弱的特点,在传输卡中加入了长线驱动功能,采用低电压差分信号(LVDS)技术,既降低了系统功耗,又实现长距离的计算机双向通信.     

机载海洋激光测深系统参量设计与最大探测深度能力分析

详细讨论了机载海洋激光测深系统最大测量深度与相关因子之间的关系，并利用最小可探测信噪比为判据，对机载海洋激光测深系统在白天和晚上工作进行了数值模拟，通过比较最大测量深度与激光脉冲峰值功率、接收视场角、接收口径和光谱接收带宽等关系，确定了系统的主要参量。以确定的参量建立的系统具有白天49m和晚上65m的最大测深能力，可完全满足在沿岸带以及岛礁的测量要求。     

Combined effects of clay modifications and compatibilizers on the formation and physical properties of melt‐mixed polypropylene/clay nanocomposites

The melt mixing technique was used to prepare various polypropylene (PP)‐based (nano)composites. Two commercial organoclays (denoted 20A and 30B) served as the fillers for the PP matrix, and two different maleated (so‐called) compatibilizers (denoted PP‐MA and SMA) were employed as the third component. The results from X‐ray diffraction (XRD) and transmission electron microscope (TEM) experiments revealed that 190 °C was an adequate temperature for preparing the nanocomposites. Nanocomposites were achieved only if specific pairs of organoclay and compatibilizer were simultaneously incorporated in the PP matrix. For example, PP/20A(5 wt %)/PP‐MA(10 wt %) and PP/30B(5 wt %)/SMA(5 wt %) composites exhibited nanoscaled dispersion of 20A or 30B in the PP matrix. Differential scanning calorimetry (DSC) results indicated that the organoclays served as nucleation agents for the PP matrix. Generally, their nucleation effectiveness increased with the addition of compatibilizers. The thermal stability enhancement of PP after adding 20A was confirmed with thermogravimetric analysis (TGA). The enhancement became more evident as a suitable compatibilizer was further added. However, for the 30B‐included composites, thermal stability enhancement was not evident. The dynamic mechanical properties (i.e., storage modulus and loss modulus) of PP increased as the nanocomposites were formed; the properties increment corresponded to the organoclay dispersion status in the matrix. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4139–4150, 2004     

Synthesis of New 13-O-Acylavermectin Bl Aglycones

Six new 13-O-acylavermectin Bl aglycones(3-8) were synthesized from avermectin B1 aglycone and their bioactivities were evaluated against Spodoptera exigua, Spodoptera eridania, Tetranychus urticae and Aphis fabae.