Serially-connected series-stub resonators for narrowband coplanar-stripline bandpass filters

In this letter, a coplanar stripline (CPS) series resonator composed of serially-connected series-stubs is proposed. This kind of resonator provides two transmission zeros close to the resonant frequency. With the proposed structure, the reactance slope parameters of the resonators are significantly increased and adjustable by changing the length ratio of the two series stubs. This is useful for designing narrowband filters which is difficult to realize with conventional series CPS resonators. The structures of the resonators are optimized for a lower radiation loss and used to design a narrowband Chebyshev bandpass filter. The simulation and experimental results show that the proposed filter provides multiple transmission zeros and high selectivity.     

Power amplifier with low average current and compact output matching network

A power amplifier with a compact output matching network and a high average operating efficiency owing to its control circuits which enable the dynamic control of the quiescent current is presented. The microwave monolithic integrated circuit of the power amplifier was designed and implemented, in order to verify the output matching network and control circuits for the 1.88-GHz band. The power-added efficiency for an average power-usage of the proposed amplifier is almost twice that of conventional power amplifiers (3.74% versus 6.86%) in urban areas.     

多级复合布尔函数性能研究

本文研究了加法复合布尔函数和乘法复合布尔函数,在平衡性、k次项系数、K次扩散准则(PC)、相关免疫 性(CI)、Walsh谱、代数次数、小项分布等方面得到了一批新结果。     

Immersive electronic books for surgical training

Immersive electronic books (IEBooks) for surgical training will let surgeons explore previous surgical procedures in 3D. The authors describe the techniques and tools for creating a preliminary IEBook, embodying some of the basic concepts.     

Reconfigurable fault tolerant networks for fast packet switching

The authors consider the design and analysis of reconfigurable networks for fast packet switching. The design constraints resulting from the use of fast packet switching that affect fault-tolerant network design are carefully studied. A reconfigurable network with high link redundancy is then proposed. An abstract replacement model that characterizes the proposed reconfigurable network is presented. Network fault tolerance problems are transformed into well known assignment problems. Two practical designs based on feasible technology are presented. An appreciable reliability improvements is achieved and full bandwidth is maintained up to a tolerable level of failures, with relatively few spare switches     

Protocol design for scalable and reliable group rekeying

We present the design and specification of a protocol for scalable and reliable group rekeying together with performance evaluation results. The protocol is based upon the use of key trees for secure groups and periodic batch rekeying. At the beginning of each rekey interval, the key server sends a rekey message to all users consisting of encrypted new keys (encryptions, in short) carried in a sequence of packets. We present a scheme for identifying keys, encryptions, and users, and a key assignment algorithm that ensures that the encryptions needed by a user are in the same packet. Our protocol provides reliable delivery of new keys to all users eventually. It also attempts to deliver new keys to all users with a high probability by the end of the rekey interval. For each rekey message, the protocol runs in two steps: a multicast step followed by a unicast step. Proactive forward error correction (FEC) multicast is used to reduce delivery latency. Our experiments show that a small FEC block size can be used to reduce encoding time at the server without increasing server bandwidth overhead. Early transition to unicast, after at most two multicast rounds, further reduces the worst-case delivery latency as well as user bandwidth requirement. The key server adaptively adjusts the proactivity factor based upon past feedback information; our experiments show that the number of NACKs after a multicast round can be effectively controlled around a target number. Throughout the protocol design, we strive to minimize processing and bandwidth requirements for both the key server and users.     

铝基印制电路板制造工艺研究

此文对一种进口铝基印制电路板的制造工艺流程进行了介绍,对所采用的制造工艺技术进行了较为详细的论述。     

Kinetics of AuSn4 migration in lead-free solders

The relatively fast diffusion of Au atoms in eutectic PbSn matrix is considered one of the contributing factors to the Au embrittlement problem. In this study, we further investigated the Au embrittlement problem in high-Sn solders. Experimentally, Sn3.5Ag (wt.%) spheres with 500-μm diameter were soldered over the Au/Ni soldering pads. It was found that some of the AuSn₄ needles that formed after reflow inside the solder migrated back to the solder/pad interface during thermal aging. However, the migration kinetics in high-Sn solders was slower compared to that in eutectic PbSn. The difference in migration kinetics of AuSn₄ in eutectic PbSn and SnAg was ascribed to the difference in the magnitudes of the Au flux and the Ni flux. In eutectic PbSn, the Au flux was much greater than that of the Ni flux, and the Au and Ni flux were in the same order of magnitude in eutectic SnAg. The relative magnitude of the Au and Ni flux changed in eutectic PbSn and SnAg because the homologous temperatures of PbSn and SnAg were different.     

Relating the Morphology of Poly(p‐phenylene vinylene)/Methanofullerene Blends to Solar‐Cell Performance

The performance of bulk‐heterojunction solar cells based on a phase‐separated mixture of donor and acceptor materials is known to be critically dependent on the morphology of the active layer. Here we use a combination of techniques to resolve the morphology of spin cast films of poly(p‐phenylene vinylene)/methanofullerene blends in three dimensions on a nanometer scale and relate the results to the performance of the corresponding solar cells. Atomic force microscopy (AFM), transmission electron microscopy (TEM), and depth profiling using dynamic time‐of‐flight secondary ion mass spectrometry (TOF‐SIMS) clearly show that for the two materials used in this study, 1‐(3‐methoxycarbonyl)propyl‐1‐phenyl‐[6,6]‐methanofullerene (PCBM) and poly[2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylene vinylene] (MDMO‐PPV), phase separation is not observed up to 50 wt.‐% PCBM. Nanoscale phase separation throughout the film sets in for concentrations of more than 67 wt.‐% PCBM, to give domains of rather pure PCBM in a homogenous matrix of 50:50 wt.‐% MDMO‐PPV/PCBM. Electrical characterization, under illumination and in the dark, of the corresponding photovoltaic devices revealed a strong increase of power conversion efficiency when the phase‐separated network develops, with a sharp increase of the photocurrent and fill factor between 50 and 67 wt.‐% PCBM. As the phase separation sets in, enhanced electron transport and a reduction of bimolecular charge recombination provide the conditions for improved performance. The results are interpreted in terms of a model that proposes a hierarchical build up of two cooperative interpenetrating networks at different length scales.     

Speciation analysis of arsenic in traditional Chinese medicines by hydride generation-atomic fluorescence spectrometry.

A method has been described for the determination of arsenic species (arsenite and arsenate) by hydride generation-atomic fluorescence spectrometry (HG-AFS). The experimental conditions that influence the fluorescence intensity and the reduction of arsenic were investigated and optimized, and the influences from foreign ions and their elimination were studied. The detection limit was found to be 79.7 ng L(-1). The proposed method was applied to the determination of arsenic species in water leachate of traditional Chinese medicines with a recovery range of 91.1-109.5%.