Decoupled two‐grid finite element method for the time‐dependent natural convection problem I: Spatial discretization

In this article, a decoupled two grid finite element method (FEM) is proposed and analyzed for the nonsteady natural convection problem using the coarse grid numerical solutions to decouple the nonlinear coupled terms, and the corresponding optimal error estimates are derived. Compared with the standard Galerkin FEM and the usual two‐grid FEM, our algorithm not only keeps good accuracy but also saves a lot of computational cost. Some numerical examples are provided to verify the performances of the decoupled two‐grid FEM. Both theoretical analysis and numerical experiments show the efficiency and effectiveness of the decoupled two‐grid FEM for the nonsteady natural convection problem. © 2015 Wiley Periodicals, Inc. Numer Methods Partial Differential Eq 31: 2135–2168, 2015     

Improvement of resistive switching fluctuations by using one step lift‐off process

Bipolar resistive switching characteristics are investigated in ZrO₂ containing Cu thin layer devices, particularly for the self‐isolated‐structure device fabricated by one step lift‐off process. Compared with the traditional‐structure device, the self‐isolated‐structure device shows more uniform resistive switching characteristics. This is because the isolation of each device cell has negligible influence on each other and thus mitigates possible crosstalk between each cell. These results suggest that the feasibility of good stabilization of the resistive switching parameters can be obtained through one step lift‐off process. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

导弹发射姿态测量方法研究

针对导弹发射姿态测量问题,提出采用高速摄像机通过斜瞄和平瞄姿态测量方法求解导弹中轴线俯仰角和方位角,仿真典型导弹起飞段近距离姿态测量,分析两种测量方法对导弹飞行姿态测量精度和适用性。仿真结果表明:平瞄和斜瞄姿态测量方法,测量误差在0.2°以内。斜瞄方式使用更便捷,通用性好。平瞄方式测量精度高,数据处理方法、机械结构相对简单,在适合的应用场合优势明显。此分析方法、分析结果为姿态测量方法选取和研究等提供一种可行的途径,也可为其它运动目标的姿态测量提供借鉴。     

Distributed Bragg reflector laser(1.8 μm) with 10 nm wavelength tuning range

We report a 1.8 μm two-section distributed Bragg reflector laser using butt-jointed In Ga As P bulk material as the waveguide core layer. The threshold current is 17 m A and the output power is 8 m W on average. The threshold current, output power, and emitting wavelength dependences on temperature are measured. The obtained wavelength tuning range is 10 nm. This device has potential applications in simultaneous multiple-gas detection.     

Electrochemical performance of lithium ion capacitors with different types of negative electrodes

The electrochemical properties of various commercial carbon materials (activated carbon (AC), graphite (GP) and hard carbon (HC)) have been investigated for use as negative electrode for lithium ion capacitors. The rate capabilities and cycle durabilities are tested up to 20 C and 1000 cycles using full cell configurations. It is found that the lithium ion could not efficiently intercalate into the activated carbon materials. The symmetrical AC/AC capacitor shows good cycle durabilities at 10 C with capacity of 17 mA h g^?1. The asymmetrical capacitors AC/GP and AC/HC with intercalated negative electrodes show higher capacities than that of AC/AC capacitor. Moreover, the AC/HC has better rate capabilities than AC/GP.     

Ordered Mesoporous Carbon and Thiolated Polyaniline Modified Electrode for Simultaneous Determination of Cadmium(II) and Lead(II) by Anodic Stripping Voltammetry

The fabrication and evaluation of a glassy carbon electrode (GCE) modified with ordered mesoporous carbon (OMC), 2‐mercaptoethanesulfonate (MES)‐tethered polyaniline (PANI) and bismuth for simultaneous determination of trace Cd²⁺ and Pb²⁺ by differential pulse anodic stripping voltammetry (DPASV) are presented here. The morphology and electrochemical properties of the fabricated electrode were respectively characterized by scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS). Experimental parameters such as PANI disposition, preconcentration potential, preconcentration time and bismuth concentration were optimized. Under optimum conditions, the fabricated electrode exhibited linear calibration curves ranged from 1 to 120 nM for Cd²⁺ and Pb²⁺. The limits of detection (LOD) were 0.26 nM for Cd²⁺ and 0.16 nM for Pb²⁺ (S/N=3), respectively. Additionally, repeatability, reproducibility, interference and application were also investigated, and the proposed electrode exhibited excellent performance. The proposed method could be extended for the development of other new sensors for heavy metal determination.     

Electrochemical performance of pre-lithiated graphite as negative electrode in lithium-ion capacitors

Electrochemical performance of the pre-lithiated graphite and the as-assembled lithium-ion capacitors (LICs) were investigated within the Li/graphite two-electrode cell and activated carbon (AC)/graphite two-electrode cell, respectively. The morphologies of the electrodes were characterized by scanning electron microscopy (SEM). The Li intercalation of Li/graphite two-electrode cell was performed using short circuiting and galvanostatic charging techniques. The Li pre-doping process was characterized by electrochemical impedance spectroscopy (EIS). The cycle performance of the LICs were investigated at the rates of 1–20 C between the cut-off voltage at 2 to 4 V. The results demonstrated that the LIC cells with 8 h pre-doping time have the best cycle performance at the high rate of 10 C. Li pre-doping methodology plays a crucial role in the electrochemical performance of the graphite electrode and the as-assembled LICs.     

Poly(phenylene oxide) modified cyanate resin for self‐healing

Self‐healing cyanate ester resins (CE) were developed by adding low molecular weight poly(phenylene oxide) (PPO) resin, yielding a high performance CE/PPO system via a low‐temperature process. The addition of PPO improved the flexural strength and fracture toughness of the CE matrix without sacrificing thermal properties. CE/PPO formulations with 5, 10, and 15 wt.% PPO showed 43%, 65%, and 105% increase in fracture toughness due to a combination of crack deflection, crack pinning, and matrix cavitation around second‐phase particles. When PPO was introduced into the CE, dielectric properties were either unchanged or declined. During thermal treatment to heal damaged CE, liquid PPO flowed into cracks, and during subsequent cooling, solidified to bond the crack surfaces. The self‐healing efficiency for CE with 15 wt.% PPO after heating to 220°C for 1 h exhibited a recovery of 73% in toughness and 81% in microtensile strength. Copyright © 2014 John Wiley & Sons, Ltd.     

Aluminum hypophosphite in combination with expandable graphite as a novel flame retardant system for rigid polyurethane foams

The main aim of this work was to investigate the synergistic effect of expandable graphite (EG) and aluminum hypophosphite (AHP) on the flame retardancy of rigid polyurethane foams (RPUFs). A series of flame retardant RPUF containing EG and AHP were prepared by one‐shot and free‐rise method. The flame retardant, thermal degradation, and combustion properties of RPUF hybrids were characterized through limiting oxygen index (LOI) test, vertical burning (UL‐94) test, thermogravimetric analysis and microscale combustion calorimeter. The LOI and UL‐94 results showed that the RPUF sample with 10 wt% EG and 5 wt% AHP passed UL‐94 V‐0 rating and reached a relatively high LOI value of 28.5%, which is superior over other EG/AHP ratios in RPUF at the equivalent filler loading. Microscale combustion calorimeter results revealed that the incorporation of EG and AHP into RPUF reduced the peak heat release rate and total heat release, thus decrease the fire risk of RPUF significantly. Incorporation of EG and AHP improved the thermal stability of RPUF as observed from the thermogravimetric analysis results and also enhanced the thermal resistance of char layer at high temperature from scanning electron microscopy and Raman spectroscopy. Moreover, it could be seen from thermogravimetric analysis/infrared spectrometry spectra that the addition of EG and AHP significantly decreased the combustible gaseous products such as hydrocarbons and ethers. Finally, the synergistic mechanism in flame retardancy was discussed and speculated. Copyright © 2014 John Wiley & Sons, Ltd.     

Synthesis of an adhesion‐enhancing polysiloxane containing epoxy groups for addition‐cure silicone light emitting diodes encapsulant

Addition‐cure silicone resin is considered as a good choice for light emitting diodes (LEDs); however, it has very poor adhesion to the substrate, which limits its practical application. A novel polysiloxane with self‐adhesion ability and higher refractive index for the encapsulating of high‐power LEDs is prepared and characterized. This polysiloxane containing vinyl groups, phenyl groups, and epoxy groups was synthesized by a sol‐gel condensation process from methacryloxy propyl trimethoxyl silane, γ‐(2,3‐epoxypropoxy)propytrimethoxysilane, and diphenylsilanediol under the catalysis of an anion exchange resin. Then, the resin‐type encapsulation material was prepared by hydrosilylation of methylphenyl hydrogen‐containing silicone resin and the newly synthesized polysiloxane material. The novel polysiloxane was characterized by ¹H‐NMR and Fourier transform infrared spectroscopy. On the basis of higher refractive index, higher transparency, excellent thermal stability, and appropriate hardness, as well as good adhesive strength between the encapsulating material and the LED lead frame (polyphthalamide), the curable silicone resin‐type encapsulation material can be used as an encapsulant for LEDs. Copyright © 2014 John Wiley & Sons, Ltd.