A broadband PHEMT MMIC distributed doubler using high-pass drain line topology

A broadband frequency doubler, based on distributed amplifier techniques, has been designed to operate from 11 to 21 GHz. In order to reject the fundamental signal over a broadband frequency range, the conventional low-pass drain line structure was replaced with the high-pass structure. This topology can suppress fundamental signals over broadband without any balanced structure so that the chip size can be more compact. Measured conversion losses of better than 10 dB from 11 to 21 GHz input frequencies are achieved with fundamental signal rejection better than 12 dB. To the best of our knowledge, this is the first demonstration of distributed doubler using the high-pass drain line topology.     

Trenched‐Sinker LDMOSFET (TS‐LDMOS) Structure for 2 GHz Power Amplifiers

This paper proposes a new LDMOSFET structure with a trenched sinker for high‐power RF amplifiers. Using a low‐temperature, deep‐trench technology, we succeeded in drastically shrinking the sinker area to one‐third the size of the conventional diffusion‐type structure. The RF performance of the proposed device with a channel width of 5 mm showed a small signal gain of 16.5 dB and a maximum peak power of 32 dBm with a power‐added efficiency of 25% at 2 GHz. Furthermore, the trench sinker, which was applied to the guard ring to suppress coupling between inductors, showed an excellent blocking performance below ?40 dB at a frequency of up to 20 GHz. These results confirm that the proposed trenched sinker should be an effective technology both as a compact sinker for RF power devices and as a guard ring against coupling.     

Exciton-polariton transition induced by elastic exciton-exciton collisions in ultrahigh quality AIGaAs alloys

The stationary and time-resolved polariton radiation in ultrahigh quality AIGaAs layers have been studied. It has been found that elastic exciton-exciton collisions lead to the appearance of a low-energy line of polariton radiation. We show that the rate of exciton-to-polariton transitions caused by elastic exciton-exciton collisions is determined not only by the density of the excitonic gas, but also by its temperature; this is in accordance with existing theoretical predictions. The text was submitted by the authors in English.     

离子束混合工艺对材料抗蚀性能的影响

本文介绍了离子束混合工艺方法。与直接注入相比较,离子束混合所使用的设备造价低1/4—1/2,而生产效率可提高1—2个数量级,因而使生产成本大幅度降低,这无疑对离子束工艺的实际应用将产生巨大的促进作用。 通过对轴承材料(GCr15和Cr4Mo4V)经Cr、N、Ta不同元素的混合处理后,在0.5M H_2SO_4和0.1M NaCl的缓冲溶液中的阳极极化曲线表明经混合处理后的两种材料试样,其抗蚀能力和抗点蚀能力均大大提高,这与直接注入的试样效果是一致的。 通过俄歇谱仪和透射电镜的分析结果表明混合是成功的,且在一定的条件下,形成非晶组织。 本文的结论是,无论是离子的直接注入还是离子束混合,对提高轴承材料的抗腐蚀性能都是有效的方法,特别是离子束混合技术具有更大的应用前景。     

Synthesis and adsorption properties of gold nanoparticles within pores of surface‐functional porous polymer microspheres

Mesoporous polymer microspheres with gold (Au) nanoparticles inside their pores were prepared considering their surface functionality and porosity. The Au/polymer composite microspheres prepared were characterized by transmission electron microscope (TEM), X‐ray diffraction (XRD), and Brunauer–Emmett–Teller (BET) techniques. The results showed that the adsorption of Au nanoparticles could be increased by imparting the pore structure and surface‐functional groups into the supporting polymer microspheres (in this study, poly (ethylene glycol dimethacrylate‐co‐acrylonitrile) and poly (EGDMA‐co‐AN) system). Above all, from this study, it was established that the porosity of the polymer microspheres is the most important factor that determines the distribution and adsorption amount of face‐centered cubic (fcc) Au nanoparticles in the final products. Our study showed that the continuous adsorption of Au nanoparticles with the aid of the large surface area and surface interaction sites formed more favorably the Au/polymer composite microspheres. The BET measurements of Au/poly(EGDMA‐co‐AN) composite microspheres reveals that the adsorption of Au nanoparticles into the pores kept the pore structure intact and made it more porous. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5627–5635, 2004     

Calculation of the Radiating Characteristics of a Thermodynamically Nonuniform Gas Medium

Passive methods of remote analysis of waste gases of industrial enterprises and aircrafts engines and gases ejected in eruptions of volcanos, in fires, and in other processes disturbing the atmosphere are now of limited utility because of the lack of well-developed mathematical techniques for solving the inverse problems of gas analysis. However, the advantage of these methods is obvious, since the equipment is limited to a receiving device and the gas medium serves as a radiator. At the same time, in modern techniques, the interpretation of measurements of emissivities of gases is performed using a phenomenological approach such that experimental data on radiation characteristics of various objects are approximated by simple polynomial relations whose coefficients are determined by minimization methods. This approach does not allow one to investigate the mechanism of the processes occurring in a radiating medium and gives no way of solving the inverse problem of monitoring the composition and thermodynamic parameters of a medium which disturbs the atmosphere by thermal effects. In elaborating theoretical methods of gas analysis, the elaboration of the direct problem of calculation of radiating characteristics of gases is of importance, since it is not clear how the emissivity of a gas medium depends on its thermodynamic parameters. This paper is devoted to the above problem. Here, the error is estimated that arises in modeling a nonuniform gas medium with an actual temperature distribution, which linearly depends on coordinate, by a uniform gas layer. It is shown that the difference between the radiation intensities calculated for uniform and nonuniform media can be significant in the practically important case where the recording device is in a zone of normal temperatures. This implies that the error of reconstruction of the spectroscopic and molecular parameters of gaseous compounds from high-temperature measurements of the radiating and absorbing characteristics should take into account the thermodynamic nonuniformity of the medium.     

New Heat-Resistant Polyimidates Derived from Bisphenols and Mono- and Dicarboxylic Acid Imidoyl Chlorides

New polyimidates were prepared from bisphenols and mono- and dicarboxylic acid imidoyl chlorides. The structures of the polymers were determined, and their physicochemical, chemical, and thermal properties were studied. The possibility of preparing film and compression materials with good mechanical characteristics from these polymers was examined.     

PBVP for integro-differential equations of volterra type in B.S.

In this paper, we study the PBVP for integro-differential equations of Volterra type in Banach spaces. By developing monotone iterative technique for the PBVP, we get some results concerning the existence of extremal solutions, which are the limits of monotone sequences.The project supported by the Natural Science Foundation of Shandong Province.     

Numerical study of simultaneous natural convection heat transfer from both surfaces of a uniformly heated thin plate with arbitrary inclination

 Numerical studies were conducted to investigate the natural convection heat transfer around a uniformly heated thin plate with arbitrary inclination in an infinite space. The numerical approach was based on the finite volume technique with a nonstaggered grid arrangement. For handling the pressure–velocity coupling the SIMPLE-algorithm was used. QUICK scheme and first order upwind scheme were employed for discretization of the momentum and energy convective terms respectively. Plate width and heating rate were used to vary the modified Rayleigh number over the range of 4.8×10⁶ to 1.87×10⁸. Local and average heat transfer characteristics were compared with regarding to the inclination angle. The empirical expressions for local and average Nusselt number were correlated. It has been found that for inclination angle less than 10^∘, the flow and heat transfer characteristics are complicated and the average Nusselt number can not be correlated by one equation while for inclination angle larger than 10^∘, the average Nusselt number can be correlated into an elegant correlation. Received on 18 April 2001 / Published online: 29 November 2001