一种用于三电平逆变器的SVPWM调制方法研究

本文从二极管箝位型三电平逆变器的基本结构出发，分析其输出状态，推导出六角形空间电压矢量图。然后从一种改进的，可以减小开关损耗，避免高的dv／dt三电平空间矢量PWM调制策略出发，建立了基于Matlab的详细仿真方案，验证了方案的可行性。文章给出了扇区判断的算法流程图，脉冲生成模块的内部结构图，其中的扇区判断的算法和脉冲生成方法对于用DSP实现三电平SVPWM具有重要的参考价值。     

DMT系统中一种易于实现的时域均衡器

总结了DMT系统中时域均衡器(TEQ)的主要设计方法，指出最大缩短信噪比(MSSNR)TEQ的最优设计方法很难实时实现。提出了一种MSSNR TEQ的次优设计方法，它首先估计出目标抽样窗的最优延迟，然后用分步求解法求出TEQ的抽头系数。和最优方法相比，次优方法的计算量大幅度减少，可实时实现，而其缩短信噪比的损失很小。仿真实验验证了次优方法的有效性。     

异步DS-CDMA系统中基于矩阵点除算法的DOA估计

针对异步DS-CDMA系统中的多用户环境,本文提出了一种低复杂度的DOA估计算法——矩阵点除算法。该算法通过对感兴趣信息的逐次分离,实现了DOA的逐路径估计。算法具有两方面显著优势:(1)克服了传统的DOA估计算法在路径总数大于天线阵元数时不能工作这一缺陷:(2)避免了计算复杂的特征值分解运算,大大降低了算法复杂度。仿真实验验证了算法的有效性。     

一种基于H.235协议的关守消息认证机制

首先对基于用户秘密散列签名的关守消息认证机制做了简单介绍,然后针对该机制的不足之处提出了一种基于H.235协议的改进方法,具有安全性高,速度快,管理方便等优点.     

Stability of Semiconductor States with Insulating and Contact Boundary Conditions

We prove the existence of global smooth solutions near a given steady state of the hydrodynamic model of the semiconductors in a bounded domain with physical boundary conditions. The steady state and the doping profile are permitted to be of large variation but the initial velocity must be small. Two cases are considered. In the first one the problem is three-dimensional, the boundary conditions are insulating and the steady state velocity vanishes. In the second one, the problem is one-dimensional, the boundary is of contact type and the steady state velocity does not vanish.     

电路过渡过程的计算机辅助分析

电路过渡过程所列方程是微分方程，本文中采用的是方框图模型分析法，即将微分方程的复杂示解分解成最基本的加（减）、乘（除）、积分（微分）、增益等运算，采用VB设计用户界面产进行计算，并给出了一算例。     

氢化丁苯共聚物结构的核磁共振波谱表征Ⅱ.微观结构的定量计算

在氢化丁苯共聚物¹³C-NMR谱脂肪碳部分谱带归属的基础上,根据各谱带的主要来源,推导出六个二单元浓度的计算公式。计算出二单元、一单元的相对含量,各结构单元的数均序列长度、嵌段含量和其它结构参数。加氢前后的¹H-和¹³C-NMR谱的组成计算结果基本一致。初步探讨了作为粘度指数改进剂的氢化丁苯共聚物微观结构与性能的关系,为合成提供了依据。     

Equivalence of variational inequality problems to unconstrained minimization

In this paper we propose a class of merit functions for variational inequality problems (VI). Through these merit functions, the variational inequality problem is cast as unconstrained minimization problem. We estimate the growth rate of these merit functions and give conditions under which the stationary points of these functions are the solutions of VI. This work was supported by the state key project “Scientific and Engineering Computing”.     

Economic cost modeling of environmental-stress-screening andburn-in

The electronics industry is highly competitive. The introduction of new advanced integrated circuits continues. The manufacturer must develop a product with adequate life cycle, high quality and low failure rate in the specified time period. Environmental stress screening (ESS) is widely used in the electronics industry to assist in eliminating early or patent failures. The bathtub curve is a common model for the failure rate of a population. The classic bathtub curve has three parts: infant mortality; useful life; and wearout. However, some electronic products have latent defects which are not detected by conventional inspection or functional testing, and occur during the product useful life. Most electronic systems have finite useful life. As a result, technology obsolescence is of concern and should be considered, This paper uses a new interpretation and development of the bathtub curve that integrates: (1) latent failures; and (2) the concept of obsolescence, by constructing an integrated cost model used to determine both optimal burn-in and ESS times in the same environment