Optical waveguide fabrication and integration with a micro-mirror inside photosensitive glass by femtosecond laser direct writing

Photosensitive glass is a potentially important material for micro-fluidic devices that can be integrated with micro-optical components for biochemical analysis. Here, we demonstrate the fabrication of optical waveguides inside glass by femtosecond laser direct writing. The influence of the laser parameters on the waveguide properties is investigated, and it is revealed that the waveguide mode can be well controlled. The single mode is achieved at a low writing energy, while the multimode is achieved with increasing energy. In spite of a longitudinally elongated elliptical shape of the cross-sectional profile, the far-field pattern of the single-mode waveguide shows an almost symmetric profile. The measured propagation loss and the coupling loss are evaluated to be ∼0.6 dB/cm and ∼1.6 dB at a wavelength of 632.8 nm, respectively, under the conditions of 1.0–2.0 μJ pulse energy and 200–500 μm/s scan speed. The increased optical loss is associated with a higher waveguide mode at higher writing energy. Furthermore, the integration of waveguides and a micromirror made of a hollow microplate inside the glass is demonstrated to bend the laser beam at an angle of 90° in a small chip. The bending loss is estimated to be smaller than 0.3 dB. PACS 42.62.-b; 42.82.Cr; 82.50.Pt; 42.79.Gn; 42.81.Qb     

Multivariable identification and controller design of an integrated flight control system

This paper investigates the multivariable identification and controller design for the longitudinal channel of a Boeing 747 transport. The transfer function matrix of the system is identified using the prediction error (PE) identification method with multivariable ARX model. An ellipsoidal parametric uncertainty set is constructed from the covariance matrix of the identified parameters. It contains the parameters of actual system at a certain probability level. The identified models and the associated uncertainty sets are validated by measuring the worst-case ν-gap and then compared with the maximum value of the generalized stability margin. In automatic flight control system or autopilots, multiple specifications criteria are needed to be satisfied concurrently, such as good holding (small static altitude holding error), fast response, smooth transition (less oscillation, overshoot). The design of a Multiple Simultaneous Specifications (MSS) controller effectively and practically is a very significant and challenging job. Liu and Mills [H.H.T. Liu, J.K. Mills, Multiple specification design in flight control system, in: Proceedings of the American Control Conference, Chicago, Illinois, 2000, pp. 1365–1369] proposed a MSS controller design method using a convex combination approach. In this paper, we apply the method [H.H.T. Liu, J.K. Mills, Multiple specification design in flight control system, in: Proceedings of the American Control Conference, Chicago, Illinois, 2000, pp. 1365–1369; H.H.T. Liu, Design combination in integrated flight control, in: Proceedings of the American Control Conference, Arlington, Virginia, 2001, pp. 494–499; H.H.T. Liu, Multi-objective design for an integrated flight control system: a combination with model reduction approach, in: Proceedings of IEEE International Symposium on Computer Aided Control System Design, Glasgow, 2002, pp. 21–26] to design a MSS controller based on the identified models of the Boeing 747 transport aircraft longitudinal channel. The controllers are also validated by simulation using the true plant transfer functions.     

Tunable negative refraction by electro-optical control in two-dimensional photonic crystal

This paper describes a simple hydrothermal procedure for high-yield synthesis of single-crystalline ZnO hexagonal nanoplates in a surfactant-free system at 70 °C. The structures and morphologies of the synthesized ZnO nanoplates are derived from characterisation by X-ray diffraction, and scanning and transmission electron microscopy. Their optical properties are recorded by Raman and photoluminescence spectroscopy. These ZnO hexagonal nanoplates exhibit the enhanced photocatalytic activity of phenol photodecomposition, suggesting that they could be served as an active system for the treatment of the waste water, in addition to their common applications. PACS 81.10.Dn; 61.10.Nz; 68.37.Hk; 78.55.Hx     

Scanning mirror on a vibrating membrane for dynamic optical trapping

A study of the variation of the spectral shape and the harmonic distribution of the high-order harmonics generated from silver plasma on the frequency chirp of the driving laser radiation (793 nm 48 fs) is reported. The results of the systematic study of the harmonic generation from the 21st order up to the 61st order (λ=13 nm) are presented. A tuning of the harmonic wavelength up to 0.8 nm can be accomplished by variation of the laser chirp. PACS 42.65.Ky; 42.79.Nv; 52.38.Mf     

Copper diffusion in Ti-Si-N layers formed by inductively coupled plasma implantation

Ternary Ti-Si-N refractory barrier films of 15 nm thick was prepared by low frequency, high density, inductively coupled plasma implantation of N into Ti_xSi_y substrate. This leads to the formation of Ti-N and Si-N compounds in the ternary film. Diffusion of copper in the barrier layer after annealing treatment at various temperatures was investigated using time-of-flight secondary ion mass spectrometer (ToF-SIMS) depth profiling, X-ray diffractometer (XRD), field emission scanning electron microscopy (FESEM), energy dispersive X-ray (EDX) and sheet resistance measurement. The current study found that barrier failure did not occur until 650 °C annealing for 30 min. The failure occurs by the diffusion of copper into the Ti-Si-N film to form Cu-Ti and Cu-N compounds. FESEM surface morphology and EDX show that copper compounds were formed on the ridge areas of the Ti-Si-N film. The sheet resistance verifies the diffusion of Cu into the Ti-Si-N film; there is a sudden drop in the resistance with Cu compound formation. This finding provides a simple and effective method of monitoring Cu diffusion in TiN-based diffusion barriers.     

Thermal properties of poly(styrene) containing brominated aryl phosphate additives

General purpose poly(styrene) is a large volume commodity polymer widely used in a range of applications. For many of these the presence of an additive to impart some flammability resistance is required. Most commonly, brominated aromatics are used for this purpose. As the polymer undergoes combustion these compounds decompose to generate bromine atoms and/or hydrogen bromide which escape to the gas phase and trap flame propagating radicals. While these species are effective in inhibiting flame propagation they present the opportunity for loss of halogen to the atmosphere. For this reason, the use of these compounds is being limited in some parts of the world. Phosphorus compounds, on the other had, impart a flame retarding influence by promoting char formation at the surface of the burning polymer. This prevents heat feedback to the polymer and consequent pyrolysis to generate fuel fragments. The combination of both bromine and phosphorus present in a single compound might generate a superior flame-retarding additive in that both modes of retardancy might be promoted simultaneously. Should this be the case smaller amounts of additive might be necessary to achieve a satisfactory level of flame retardancy. A series of such additives, brominated aryl phosphates, has been synthesized and fully characterized spectroscopically. Blends of these additives, at various levels, with poly(styrene) have been examined by DSC, TG and in the UL-94 flame test. The flammability of the polymer is dramatically diminished by the presence of the additive.     

Magnetisation reversal in media with perpendicular anisotropy

In this paper, we discuss two key aspects of magnetisation reversal in magnetic thin films with perpendicular anisotropy. Firstly, a study has been made of the additional field required to erase data written perpendicular to a thin film recording disk as the linear data density is increased. It has been found that an increase in data density from 40 to 360 kfci results in an increase of 1.25 kOe in the field required to erase the data. Secondly, the effect of varying the level of exchange coupling by co-sputtering CoCrPt samples with SiO₂ has been studied using a characterisation technique that is independent of the self-demagnetising field. It has been found that the samples are fully exchange de-coupled when the film contains >9.8% SiO₂ and the activation volume of reversal remains constant for higher levels of SiO₂.     

Spectral attenuation measurement for fluoride glass single-mode fibres by Fourier transform techniques

A new spectral attenuation measurement system using a Fourier transform spectrometer is developed. The Fourier transform spectral attenuation measurement (FT-SAM) system makes the signal acquisition time for a wide wave-length range of 1.0?4.2? much shorter than measurement with a conventional dispersive spectral attenuation measurement system. The spectral attenuation for a fluoride glass single-mode fibre, with a minimum loss of 3±1 dB/km at 2.5?m, is measured with this system.     

Energy level alignment between C60 and Al using ultraviolet photoelectron spectroscopy

The energy level alignment between C₆₀ and Al has been investigated by using ultraviolet photoelectron spectroscopy. To obtain the interfacial electronic structure between C₆₀ and Al, C₆₀ was deposited on a clean Al substrate in a stepwise manner. The valence-band spectra were measured immediately after each step of C₆₀ deposition without breaking the vacuum. The measured onset of the highest occupied molecular orbital energy level was located at 1.59 eV from the Fermi level of Al. The vacuum level was shifted 0.68 eV toward lower binding energy with additional C₆₀ layers. The observed vacuum level shift means that the interface dipole exists at the interface between C₆₀ and Al. The barrier height of electron injection from Al to C₆₀ is 0.11 eV, which is smaller value than that of hole injection.