A redundant multivalued logic for a 10-Gb/s CMOS demultiplexer IC

A redundant multivalued logic is proposed for high-speed communication ICs. In this logic, serial binary data are received and converted into parallel redundant multivalued data. Then they are restored into parallel binary data. Because of the multivalued data conversion, this logic makes it possible to achieve higher operating speeds than that of a conventional binary logic. Using this logic, a 1:4 demultiplexer (DEMUX, serial-parallel converter) IC was fabricated using a 0.18-/spl mu/m CMOS process. The IC achieved an operating speed of 10 Gb/s with a supply voltage of only 1.3 V and with power consumption of 38 mW. This logic may achieve CMOS communication ICs with an operating speed several times greater than 10 Gb/s.     

A New Comb Circular Polarizer Suitable for Millimeter‐Band Application

This letter presents a new polarizer which has a simple comb structure inside a circular waveguide. The electrical performance of the proposed comb polarizer is optimized by a circular waveguide radius and by the physical parameters of the comb plates. This polarizer is suitable for providing good performance in millimeter‐band application because of its simple structure and low fabrication cost. In our experiments the dual‐band comb polarizer designed in band 1(K) and band 2(Ka) showed good electrical performance without any tuning elements.     

On the Feasibility of Growing Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 Single Crystals

Pb[(Zn_1/3Nb_2/3)_0.91Ti_0.09]O₃ (PZNT91/9) single crystals were grown by two methods: from solution using PbO as a self‐fluxing agent (SC method) and directly from the melt without fluxing (MC method). In both growth methods, an allomeric Pb[(Mg_1/3‐Nb_2/3)_0.69Ti_0.31]O₃ (PMNT69/31) single crystal was used as a seed. X‐ray diffraction patterns of ground crystals showed that phase‐pure perovskite PZNT91/9 single crystals were successfully fabricated by the above two methods. The composition of the crystals obtained by both the SC and MC methods was analyzed using X‐ray fluorescence, which confirmed that the crystal composition is close to the nominal value, although volatilization of PbO and segregation during crystal growth are inevitable. The MC PZNT91/9 crystals exhibit excellent piezoelectric properties, with the piezoelectric constant, d₃₃, in the range of 1800–2200 pC N^–1. This value is comparable to that of the SC crystals. However, the MC crystals show an abnormal dielectric behavior. In contrast with the SC crystals, in the MC crystals a much broader dielectric peak appears in the dielectric response curves, accompanied by a much lower peak temperature of around 105 °C. Furthermore, frequency dispersion is apparent over a much wider temperature range (even more apparent than in pure relaxors), where a large, i.e., about 70 °C, full width at half maximum (FWHM) for the dielectric peaks is observed in the dielectric response. It is speculated that such an unusual phenomenon correlates with defects, microinhomogeneities, and polar regions in the as‐grown MC crystals. The origins of this abnormality have not been interpreted in detail until now. However, optical observation of the domain structure confirms that both the SC and MC crystals possess complex structural states.     

New design of hybrid-type self-bearing motor for small, high-speed spindle

A new structure of hybrid (HB)-type self-bearing motor is proposed for miniature spindle motors. The proposed design combines the HB-type self-bearing motor and HB active magnetic bearing in the common stator and rotor pair to generate large radial forces. First, the principle and theoretical background are introduced. Then, the air gap flux is analyzed by the finite element method, and radial forces for the proposed and standard-type HB self-bearing motors are compared. Finally, experiments are conducted to confirm the performance of the proposed motor. The motor can run at relatively high rotating speed with relatively high torque compared with its small size. The levitation is very stable and the motor indicates good performance for practical application.     

Method for Preparation of Semiconductor Quantum‐Rod Lasers in a Cylindrical Microcavity

An efficient method for preparation of semiconductor quantum rod films for robust lasing in a cylindrical microcavity is reported. A capillary tube, serving as the laser cavity, is filled with a solution of nanocrystals and irradiated with a series of intense nanosecond laser pulses to produce a nanocrystal film on the capillary surface. The films exhibit intense room‐temperature lasing in whispering‐gallery modes that develop at the film–capillary interface as corroborated from the spacing detected for the lasing modes. Good lasing stability is observed at moderate pump powers. The method was applied successfully to several quantum‐rod samples of various sizes.     

Exposed Die-Top Encapsulation Molding for an Improved High- Performance Flip Chip BGA Package

The recent advancement in high- performance semiconductor packages has been driven by the need for higher pin count and superior heat dissipation. A one-piece cavity lid flip chip ball grid array (BGA) package with high pin count and targeted reliability has emerged as a popular choice. The flip chip technology can accommodate an I/O count of more than five hundreds500, and the die junction temperature can be reduced to a minimum level by a metal heat spreader attachment. None the less, greater expectations on these high-performance packages arose such as better substrate real estate utilization for multiple chips, ease in handling for thinner core substrates, and improved board- level solder joint reliability. A new design of the flip chip BGA package has been looked into for meeting such requirements. By encapsulating the flip chip with molding compound leaving the die top exposed, a planar top surface can be formed. A, and a flat lid can then be mounted on the planar mold/die top surface. In this manner the direct interaction of the metal lid with the substrate can be removed. The new package is thus less rigid under thermal loading and solder joint reliability enhancement is expected. This paper discusses the process development of the new package and its advantages for improved solder joint fatigue life, and being a multichip package and thin core substrate options. Finite-element simulations have been employed for the study of its structural integrity, thermal, and electrical performances. Detailed package and board-level reliability test results will also be reported     

Novel method for simultaneous formation of wires and vias of a printed circuit board using nanoporous body

A new type of a flexible printed circuit board with landless vias is developed using a novel method called interconnection via nanoporous structure (INPS). This method can make wires and vias of the printed circuit board simultaneously by a single photo-exposure process. A new photo-induced selective plating method was used to impregnate a nanoporous substrate with copper, and a new photomask was designed, which constitutes of a completely vacant large hole for via and aggregation patterns of very fine holes for wire. Because of the simple process, the INPS board is characterized by landless vias and very fine circuit. Owing to the structure, it is also characterized by flexibility and detachable wires.     

Design methodologies for high-performance noise-tolerant XOR-XNOR circuits

Scaling down to deep submicrometer (DSM) technology has made noise a metric of equal importance as compared to power, speed, and area. Smaller feature size, lower supply voltage, and higher frequency are some of the characteristics for DSM circuits that make them more vulnerable to noise. New designs and circuit techniques are required in order to achieve robustness in presence of noise. Novel methodologies for designing energy-efficient noise-tolerant exclusive-OR-exclusive- NOR circuits that can operate at low-supply voltages with good signal integrity and driving capability are proposed. The circuits designed, after applying the proposed methodologies, are characterized and compared with previously published circuits for reliability, speed and energy efficiency. To test the driving capability of the proposed circuits, they are embedded in an existing 5-2 compressor design. The average noise threshold energy (ANTE) is used for quantifying the noise immunity of the proposed circuits. Simulation results show that, compared with the best available circuit in literature, the proposed circuits exhibit better noise-immunity, lower power-delay product (PDP) and good driving capability. All of the proposed circuits prove to be faster and successfully work at all ranges of supply voltage starting from 3.3 V down to 0.6 V. The savings in the PDP range from 94% to 21% for the given supply voltage range respectively and the average improvement in the ANTE is 2.67X.     

Supermedia-enhanced Internet-based telerobotics

This paper introduces new planning and control methods for supermedia-enhanced real-time telerobotic operations via the Internet. Supermedia is the collection of video, audio, haptic information, temperature, and other sensory feedback. However, when the communication medium used, such as the Internet, introduces random communication time delay, several challenges and difficulties arise. Most importantly, random communication delay causes instability, loss of transparency, and desynchronization in real-time closed-loop telerobotic systems. Due to the complexity and diversity of such systems, the first challenge is to develop a general and efficient modeling and analysis tool. This paper proposes the use of Petri net modeling to capture the concurrency and complexity of Internet-based teleoperation. Combined with the event-based planning and control method, it also provides an efficient analysis and design tool to study the stability, transparency, and synchronization of such systems. In addition, the concepts of event transparency and event synchronization are introduced and analyzed. This modeling and control method has been applied to the design of several supermedia-enhanced Internet-based telerobotic systems, including the bilateral control of mobile robots and mobile manipulators. These systems have been experimentally implemented in three sites test bed consisting of robotic laboratories in the USA, Hong Kong, and Japan. The experimental results have verified the theoretical development and further demonstrated the stability, event transparency, and event synchronization of the systems.