Buckling of a stiff thin film on a compliant substrate in large deformation

A finite-deformation theory is developed to study the mechanics of thin buckled films on compliant substrates. Perturbation analysis is performed for this highly nonlinear system to obtain the analytical solution. The results agree well with experiments and finite element analysis in wavelength and amplitude. In particular, it is found that the wavelength depends on the strain. Based on the accurate wavelength and amplitude, the membrane and peak strains in thin films, and stretchability and compressibility of the system are also obtained analytically.     

Multi-layer thin films/substrate system subjected to non-uniform misfit strains

Current methodologies used for the inference of thin film stress through curvature measurement are strictly restricted to stress and curvature states that are assumed to remain uniform over the entire film/substrate system. These methodologies have recently been extended to a single layer of thin film deposited on a substrate subjected to the non-uniform misfit strain in the thin film. Such methodologies are further extended to multi-layer thin films deposited on a substrate in the present study. Each thin film may have its own non-uniform misfit strain. We derive relations between the stresses in each thin film and the change of system curvatures due to the deposition of each thin film. The interface shear stresses between the adjacent films and between the thin film and the substrate are also obtained from the system curvatures. This provides the basis for the experimental determination of thin film stresses in multi-layer thin films on a substrate.     

Banana-shaped mesogens: a new homologous series of compounds exhibiting the B7 mesophase

The synthesis and characterization of a new homologous series of compounds, the 2-cyano-1,3-phenylene bis[4-(4-n-alkoxyphenyliminomethyl)benzoates] derived from 2-cyanoresorcinol is reported. All the compounds are enantiotropic mesogens and exhibit the fascinating B₇ mesophase. The characterization of the mesophase was performed using polarizing optical microscopy, differential scanning calorimetry, X-ray diffraction and electro-optical studies.     

10?30 GHz monolithic GaAs travelling-wave divider/combiner

A four-way monolithic GaAs travelling-wave power divider/combiner has been designed, fabricated and evaluated. With a design centre frequency of 20 GHz, a bandwidth of from 10 GHz to 30 GHz has been measured. The insertion loss per dividing or combining action is less than 0.5 dB, with isolation between ports no worse than 20 dB. The input/output VSWRs are better than 2:1 across the same band. This divider/combiner can readily be used with monolithic GaAs power FET amplifiers to produce a several-fold increase in output powers over the 10 to 30 GHz frequency range.     

Parametric modeling of somatosensory evoked potentials

In this paper, we examine methods of characterizing somatosensory evoked potentials (SEP's) in both the time and frequency domains. We have found that the truncated impulse response (TIR) method produced an accurate time domain model of the SEP signals at model orders greatly reduced from the original state space matrix. The TIR method was valuable for smoothing signals that were slightly corrupted by noise. In this case, the simulated data sequence was close to the original data sequence in the mean squared error sense. For signals that were greatly corrupted by noise, the TIR method was not able to perform as well. Therefore, the TIR method was not a feature extraction method but was valuable for data simulation. In the frequency domain, we have used the autoregressive moving average model (ARMA) to parameterize the SEP signal. An overdetermined set of Yule-Walker equations was created to determine the autoregressive (AR) parameters of the original data with the model order established by the singular value decomposition. From these AR parameters, a residual time series was generated which was used to find the moving average parameters. The resulting ARMA model was used to produce a simulated data sequence. The frequency domain characteristics of the simulated sequence and the corresponding power spectral density of the ARMA filter were very close to the periodogram of the original data sequence. Accurate parameterization was achieved for the SEP waveforms at low filter lengths.     

Linearity stablized fiber-optic thermometer using pseudo-heterodyne phase detection

A temperature sensor using a fiber-optic Fabry-Perot interferometer is described. A pseudo-heterodyne detection scheme is adopted to read the light phase difference in the Fabry-Perot interference output. A higher harmonic components comparison method is used to stabilize the system and to increase detection linearity. This system realizes not only highly sensitive temperature sensing with good linearity and minimal adjusting error, but also application to the sensing of other physical quantities such as vibrations. Additionally, the signal-to-noise ratio and distortion of the detected signal are investigated as functions of fiber end reflectivity. These results will be useful in designing a high performance fiber-optic Fabry-Perot thermometer.     

Hot-carrier reliability of 20V MOS transistors in 0.13 μm CMOS technology

This paper presents results of reliability investigation of 20 V N-Drift MOS transistor in 0.13 μm CMOS technology. Due to high performances required for CMOS applications, adding high voltage devices becomes a big challenge to guarantee the reliability criteria. In this context, new reliability approaches are needed. Safe Operating Area are defined for switch, V_ds limited and V_gs limited applications in order to improve circuit designs. For V_ds limited applications, deep doping dose effects in drift area are investigated in correlation to lifetime evaluations based on device parameter shifts under hot carrier stressing. To further determine the amount and locations of hot carriers injections, accurate 2D technological and electrical simulations are performed and permit to select the best compromise between performance and reliability for N-Drift MOS transistor.     

A numerical and experimental investigation of the interactions between a non‐uniform planar array of incompressible free jets

The interaction between multiple incompressible air jets has been studied numerically and experimentally. The numerical predictions have been first validated using experimental data for a single jet configuration. The spreading features of five unequal jets in the configuration of one larger central jet surrounded by four smaller equi‐distant jets, have been studied, for different lateral spacing ratios of 1.5, 2.0 and 2.5 and a central jet Reynolds number of 1.24×105 (corresponding to a Mach number of 0.16). Flow of five equal jets has also been simulated, for the sake of comparison. The jet interactions commence at an axial distance of about 3–4 diameters and complete by an axial distance of about 10 diameters for the lowest spacing ratio of 1.5. For larger spacing ratios, the length required for the start and completion of jet interaction increase. Peripheral jets bend more towards the central jet and merge at a smaller distance, when their sizes are smaller than that of the central jet. The entrainment ratio for multiple jets is higher than that for a single jet. Excellent agreement is observed between the experimental data and theoretical predictions for both mean flow field and turbulent quantities, at regions away from the jet inlet. The potential core length and initial jet development, however, are not predicted very accurately due to differences in the assumed and actual velocity profiles at the jet inlet. Copyright © 2004 John Wiley & Sons, Ltd.     

Assessment of two‐equation turbulence modelling for high Reynolds number hydrofoil flows

This paper presents an evaluation of the capability of turbulence models available in the commercial CFD code FLUENT 6.0 for their application to hydrofoil turbulent boundary layer separation flow at high Reynolds numbers. Four widely applied two‐equation RANS turbulence models were assessed through comparison with experimental data at Reynolds numbers of 8.284×106 and 1.657×107. They were the standard k–εmodel, the realizable k–εmodel, the standard k–ωmodel and the shear‐stress‐transport (SST) k–ωmodel. It has found that the realizable k–εturbulence model used with enhanced wall functions and near‐wall modelling techniques, consistently provides superior performance in predicting the flow characteristics around the hydrofoil. Copyright © 2004 John Wiley & Sons, Ltd.