Fabrication of 1.55 μm VCSELs on Si using metallic bonding

Using AuGeNiCr multilayered metals as the wafer bonding medium, long-wavelength GaInAsP/InP vertical cavity surface emitting lasers employing Al-oxide/Si as the upper and lower distributed Bragg reflectors were fabricated on Si substrate with the bonding interface formed outside the vertical cavity surface emitting laser cavity. Laser emission at 1.545 μm was measured under pulsed operations near room temperature. The low-temperature metallic bonding process demonstrates a great potential in device fabrication     

Optimal Planar Interception with Fixed End Conditions: Approximate Solutions

In a previous paper (Ref. 1), an exact solution of the optimal planar interception with fixed end conditions was derived in closed form. The optimal control was expressed as an explicit function of the state variables and two fixed parameters, obtained by solving a set of nonlinear algebraic equations involving elliptic integrals. In order to facilitate the optimal control implementation, the present paper derives a highly accurate simplified solution assuming that the ratio of the pursuer turning radius to the initial range is small. An asymptotic expansion further reduces the computational workload. Construction of a near-optimal open-loop control, based on the approximations, completes the present paper.     

Finite element beam propagation method for three-dimensionaloptical waveguide structures

A beam propagation method (BPM) based on the finite element method (FEM) is described for longitudinally varying three-dimensional (3-D) optical waveguides. In order to avoid nonphysical reflections from the computational window edges, the transparent boundary condition is introduced. The present algorithm using the Pade approximation is, to our knowledge, the first wide-angle finite element beam propagation method for 3-D waveguide structures. To show the validity and usefulness of this approach, numerical results are shown for Gaussian-beam excitation of a straight rib waveguide and guided-mode propagation in a Y-branching rib waveguide     

A fully soft-switched extended-period quasi-resonantpower-factor-correction circuit

This paper presents the design criteria, procedure, and implementation of a soft-switched power-factor-correction (PFC) circuit based on the extended-period quasi-resonant (EPQR) principles. All power electronic devices including switches and diodes in the circuit are fully soft switched. The design method is demonstrated in a prototype circuit. The operating principles are confirmed with computer simulation and experimental results. A comparison of the EP-QR operation and zero-voltage-transition (ZVT) pulse-width modulation (PWM) method     

Digitally tunable optical filters using arrayed-waveguide grating(AWG) multiplexers and optical switches

Two novel configurations for digitally tunable optical filters based on arrayed-waveguide grating (AWG) multiplexers are described in detail with emphasis on the connection of the AWG multiplexer and optical switches. Performance comparisons show that conventional configurations are disadvantaged by the switch size required and loss imbalance among the optical frequency-division-multiplexed (FDM) channels; the proposed configurations require only O(√(N)) switch elements to select one of N FDM channels, and the loss imbalance is lower by up to 75% in decibel     

Modulation and Equalisation Considerations for High Performance Radio LANs

The European Telecommunications Standards Institute (ETSI) has recently defined a European standard for a high performance radio LAN (known as HIPERLAN). To operate as wired LAN replacements, these systems will operate at 5.2 GHz and support instantaneous bit rates of just under 24 Mb/s. To counteract the time dispersive nature of the indoor radio channel, the use of adaptive equalisation is suggested. In this paper a number of possible modulation and equalisation techniques are presented and, in particular, the Bit Error Rate (BER) performance of quasi-coherent GMSK combined with Decision Feedback Equalisation is explored through computer simulation. The trade off between symbol spaced and fractionally spaced equalisation is considered together with the importance of feedfoward and feedback synchronisation to the channel's power delay profile. The paper also includes a comparison of the RLS and LMS based training algorithms and compares the modem developed under the ESPRIT III LAURA project with that specified in HIPERLAN.The application of dual antenna diversity is investigated and its impact on the number of received error free data packets obtained as a function of signal leval and rms delay spread. The use of such diversity is shown to greatly improve the BER performance of a HIPERLAN modem. The problem of frequency offset is considered and modifications are proposed to the HIPERLAN frame structure to improve the receiver's tolerance to such errors. Important practical issues such as frame and symbol synchronisation, frequency offset correction and hardware implementation are discussed from both the LAURA and HIPERLAN viewpoint.     

Driving voltage reduction in a two-phase CCD by suppression ofpotential pockets in inter-electrode gaps

This study reports an optimum design for a two-phase charge-coupled device (CCD) and limitations on its driving voltage reduction. The two-phase CCD to be used as a horizontal-CCD (H-CCD) in a CCD image sensor requires low-voltage and high-speed operation. Reducing the driving voltage, however, may induce potential pockets in the channel under the inter-electrode gaps which results in a fatal decrease in charge-transfer efficiency. In this case it is necessary to optimize the CCD design to be free of pocket generation. For this requirement, we conducted two-dimensional (2-D) device simulations for the two-phase CCD, whose potential barriers are formed by boron ion-implantation. Our simulations indicated that the edge position of the potential barrier region and the dose of boron-ion implantation would be important parameters for controlling the size of potential pockets. At an optimum edge position and a boron dose, the minimum driving voltage appears to be reducible to 1.1 V. Characteristics of potential pockets and methods of their suppression are also discussed     

A low-resistance self-aligned T-shaped gate for high-performancesub-0.1-μm CMOS

This paper describes the high performance of T-shaped-gate CMOS devices with effective channel lengths in the sub-0.1-μm region. These devices were fabricated by using selective W growth, which allows low-resistance gates smaller than 0.1 μm to be made without requiring fine lithography alignment. We used counter-doping to scale down the threshold voltage while still maintaining acceptable short-channel effects. This approach allowed us to make ring oscillators with a gate-delay time as short as 21 ps at 2 V with a gate length of 0.15 μm. Furthermore, we experimentally show that the high circuit speed of a sub-0.1-μm gate length CMOS device is mainly due to the PMOS device performance, especially in terms of its drivability     

Quick estimation of rare events in stochastic networks

This paper presents a method for fast estimation of probabilities of rare events in stochastic networks, with a particular emphasis on coherent reliability systems. The method is based on the concepts of likelihood-ratios (LR), change of probability measure and the bottleneck-cut in the network. Both polynomial and exponential-time Monte Carlo estimators are defined, and conditions under which the time complexity of the proposed LR estimators is bounded by a polynomial are discussed. The accuracy of the method depends only on the size (cardinality) of the bottleneck-cut, not on the topology and actual size of the network. Supporting numerical results are presented, with the cardinality of the bottleneck-cut ⩽20     

Influence of quantum capture and tunneling mechanisms on the dark current of bound-to-continuum quantum-well infrared photodetectors

We present a theoretical model for the dark current of bound-to-continuum quantum-well infrared photodetectors (QWIPs), by considering the field-induced mixing effect, tunneling rate and phonon scattering rate between bound and continuum states. Using this model, we can see clearly how these mechanisms significantly influence the Fermi levels of bound and continuum electrons, and thus, the dark current. Nonlinear temperature dependence of the dark current at low temperature is predicted and discussed in detail. The simulated dark currents exhibit good agreement with the experimental results, without use of parameter fitting techniques.