A redundant multivalued logic for a 10-Gb/s CMOS demultiplexer IC

A redundant multivalued logic is proposed for high-speed communication ICs. In this logic, serial binary data are received and converted into parallel redundant multivalued data. Then they are restored into parallel binary data. Because of the multivalued data conversion, this logic makes it possible to achieve higher operating speeds than that of a conventional binary logic. Using this logic, a 1:4 demultiplexer (DEMUX, serial-parallel converter) IC was fabricated using a 0.18-/spl mu/m CMOS process. The IC achieved an operating speed of 10 Gb/s with a supply voltage of only 1.3 V and with power consumption of 38 mW. This logic may achieve CMOS communication ICs with an operating speed several times greater than 10 Gb/s.     

Experimental and numerical assessment of gate-lag phenomena in AlGaAs-GaAs heterostructure field-effect transistors (FETs)

Gate-lag effects are characterized in AlGaAs-GaAs heterostructure field-effect transistors (HFETs) by means of measurements and numerical device simulations. Gate lag increasingly affects device switching at increasing ungated recess extension, suggesting that responsible deep levels be located at the ungated, recess surface of the HFET. Gate lag diminishes by making the off-state gate-source voltage less negative and by increasing the drain bias. Increasing the temperature makes the turn-on transient faster at low drain bias, while slightly delaying it at high drain bias. Numerical device simulations accounting for acceptor-like traps at the ungated surface predict gate-lag phenomena in good agreement with experiments, reproducing correctly the observed bias and temperature dependences. Simulations show that surface states behave, during the turn-on transient, as hole traps capturing holes attracted at the ungated surface by the negative trapped charge.     

A New Hand-Held Microsystem Architecture for Biological Analysis

This paper presents a hand-held microsystem based on new fully integrated magnetoresistive biochips for biomolecular recognition (DNA hybridization, antibody antigen interaction, etc.). Magnetoresistive chip surfaces are chemically treated, enabling the immobilization of probe biomolecules such as DNA or antibodies. Fluid handling is also integrated in the biochip. The proposed microsystem not only integrates the biochip, which is an array of 16times16 magnetoresistive sensors, but it also provides all the electronic circuitry for addressing and reading out each transducer. The proposed architecture and circuits were specifically designed for achieving a compact, programmable and portable microsystem. The microsystem also integrates a hand-held analyzer connected through a wireless channel. A prototype of the system was already developed and detection of magnetic nanoparticles was obtained. This indicates that the system may be used for magnetic label based bioassays     

A New Comb Circular Polarizer Suitable for Millimeter‐Band Application

This letter presents a new polarizer which has a simple comb structure inside a circular waveguide. The electrical performance of the proposed comb polarizer is optimized by a circular waveguide radius and by the physical parameters of the comb plates. This polarizer is suitable for providing good performance in millimeter‐band application because of its simple structure and low fabrication cost. In our experiments the dual‐band comb polarizer designed in band 1(K) and band 2(Ka) showed good electrical performance without any tuning elements.     

A tree partitioning dynamic policy for OVSF codes assignment in wideband CDMA

This paper proposes some novel techniques to accommodate users with different rate requirements in a wideband code-division multiple-access system employing orthogonal variable spreading factor codes. Two simple static code assignment strategies are first considered, and an improvement based on multicode assignment. Then the new idea of tree partitioning is introduced and used to devise a dynamic code reassignment algorithm. The behavior of these different techniques is experimentally investigated, in terms of call blocking probability and number of required reassignments. The tree partitioning method exhibits very good performances.     

Control system design on a power-split CVT for high-power agricultural tractors

The problem considered in this paper is the design and tuning of the control system of a power-split continuously variable transmission (CVT) used in high-power tractors. Power-split CVTs are characterized by the combination of a traditional mechanical transmission and by a continuously-variable transmission. This guarantees, at the same time, smooth variations of the transmission-ratio and high efficiency of the overall transmission system. The control architecture of an hydrostatic power-split CVT is constituted by three main parts: 1) servo-controller on the current of the valve which drives the hydraulic transmission; 2) a servo-controller on the hydraulic transmission-ratio; and 3) a synchronizer which coordinates the hydraulic and the mechanical parts of the CVT. In this work, these three controllers are fully developed, including: design, implementation, and evaluation on an experimental system.     

Experimental real-time detector of GSM terminals

The authors present an experimental real-time GSM terminal detector, to be installed in a restricted area. The detector triggers terminal signaling, which can be captured.     

Exposed Die-Top Encapsulation Molding for an Improved High- Performance Flip Chip BGA Package

The recent advancement in high- performance semiconductor packages has been driven by the need for higher pin count and superior heat dissipation. A one-piece cavity lid flip chip ball grid array (BGA) package with high pin count and targeted reliability has emerged as a popular choice. The flip chip technology can accommodate an I/O count of more than five hundreds500, and the die junction temperature can be reduced to a minimum level by a metal heat spreader attachment. None the less, greater expectations on these high-performance packages arose such as better substrate real estate utilization for multiple chips, ease in handling for thinner core substrates, and improved board- level solder joint reliability. A new design of the flip chip BGA package has been looked into for meeting such requirements. By encapsulating the flip chip with molding compound leaving the die top exposed, a planar top surface can be formed. A, and a flat lid can then be mounted on the planar mold/die top surface. In this manner the direct interaction of the metal lid with the substrate can be removed. The new package is thus less rigid under thermal loading and solder joint reliability enhancement is expected. This paper discusses the process development of the new package and its advantages for improved solder joint fatigue life, and being a multichip package and thin core substrate options. Finite-element simulations have been employed for the study of its structural integrity, thermal, and electrical performances. Detailed package and board-level reliability test results will also be reported     

Supermedia-enhanced Internet-based telerobotics

This paper introduces new planning and control methods for supermedia-enhanced real-time telerobotic operations via the Internet. Supermedia is the collection of video, audio, haptic information, temperature, and other sensory feedback. However, when the communication medium used, such as the Internet, introduces random communication time delay, several challenges and difficulties arise. Most importantly, random communication delay causes instability, loss of transparency, and desynchronization in real-time closed-loop telerobotic systems. Due to the complexity and diversity of such systems, the first challenge is to develop a general and efficient modeling and analysis tool. This paper proposes the use of Petri net modeling to capture the concurrency and complexity of Internet-based teleoperation. Combined with the event-based planning and control method, it also provides an efficient analysis and design tool to study the stability, transparency, and synchronization of such systems. In addition, the concepts of event transparency and event synchronization are introduced and analyzed. This modeling and control method has been applied to the design of several supermedia-enhanced Internet-based telerobotic systems, including the bilateral control of mobile robots and mobile manipulators. These systems have been experimentally implemented in three sites test bed consisting of robotic laboratories in the USA, Hong Kong, and Japan. The experimental results have verified the theoretical development and further demonstrated the stability, event transparency, and event synchronization of the systems.