IPv6和基于IPv6的网络设计

对IPv6协议的主要内容进行了简要介绍,并针对IPv6的特点对基于IPv6的网络设计进行了探讨。     

中国邮路问题的一个解法

本给出中国邮路问题的一个解法。虽然它仍只是初始方案，但因考虑了问题的足够信息，因而这种方案至少拉近了与最优解的距离。     

MC模式下顾客需求与厂商供应的纳什均衡

在大规模定制(MC，Mass Customization)模式下，基于市场需求的复杂化，厂商对个性化的顾客需求很难做出及时准确的反应，而且由于其自身生产能力的限制，不可能对所有的个性化用户进行一一地满足，只可能对已经存在的个性化需求，根据自身的生产能力和规模，以利润最大化及顾客对产品的满意度为目标，对个性化需求进行较准确地预测，从而正确指导生产。本通过博弈论的方法，提出了一个基于顾客对产品的满意度及企业的利润的一个非合作博弈模型，并给出求解纳什均衡的方法。     

Parallel multilevel fast multipole method for solving large-scale problems

The Multilevel Fast Multipole Method (FMM) is a well-established method and can be applied to solve electromagnetic (EM) scattering problems. Compared with other traditional methods, it requires less computational time and memory. However, constrained by a single processor's speed and memory limitations, the problem size that can be solved by serial implementation is still relatively small. For a million-unknown target, the computational time on a single processor is intolerable, and memory could be easily exhausted. Parallel-computing technology, which can utilize multiprocessors, provides an efficient way to solve electrically large-scale EM problems. This paper will focus on discussing the parallel methodologies applied to a multilevel FMM code, as well as demonstrating the computational efficiency of the parallel approach.     

Low Cost, High Efficiency, Gain Flattened L Band EDFA Using FBGs as C Band Seed Generators

A low cost, coolerless 980nm diode pumped, gain flattened L band EDFA with fast transient control, high pump efficiency and gain clamping effect was realized by using FBGs as C band seed generators.     

In-Situ Intrinsic Interface Strength Measurement at Elevated Temperatures and its Relationship to Interfacial Structure

A previously developed laser spallation technique has been modified to measure the tensile strength of thin film interfaces in-situ at temperatures up to 1100°C. Tensile strengths of Nb/A-plane sapphire, FeCrAl/A-plane sapphire and FeCrAlY/A-plane sapphire were measured up to 950°C. The measured strengths at high temperatures were substantially lower compared with their corresponding strengths at ambient temperature. For example, at 850°C, the interface tensile strength for the Nb/sapphire (151 ± 17 MPa), FeCrAl/sapphire (62 ± 8 MPa) and FeCrAlY/sapphire (82 ± 11 MPa) interface systems were lower by factors of approximately, 3, 5, and 8, respectively, over their corresponding ambient values. These results underscore the importance of using such in-situ measured values under operating conditions as the failure criterion in any life prediction or reliability models of such coated systems where local interface temperature excursions are expected. The results on alloy film interfaces also demonstrate that the presence of Y increases the strength of FeCrAl/Al₂O₃ interfaces.     

70K温区混合工质分凝分离循环节流制冷机实验研究

混合工质节流制冷机正在许多方面获得越来越广泛的应用。文中设计了一种新型的混合工质分凝分离循环 ,建立了实验系统 ,并在 70 K温区进行了实验。实验结果表明 ,节流制冷机可以达到 6 5 .3K的低温 ,并在 72 K温度提供 1W的制冷量 ,输入功率为 5 0 0 W。     

Giant Magneto-Impedance of Co50Ni22Ga28 Alloy with High Chemical Ordering

The microstructure of CosoNi22Ga28 ribbon with the L10 structure is examined. The band-like morphology is observed. These bands with the width in a range of 40-200 nm appear along the transverse direction of the ribbon. The giant magnetoimpedance （GMI） effect in this alloy is measured. The results show that Co5oNi22Ga28 exhibits a sharp peak of the GAI effect. The maximum GAH ratio up to 360% is detected. The GMI effect measured versus temperature shows large jumps of the magnetoimpedance amplitude at the reversal martensitic transformation temperature 240℃ and Curie temperature 375℃C respectively. The jump ratios of the magnetoimpedance amplitude examined at these temperatures are about 5 and 10, respectively.     

Experimental investigation and theoretical modeling of liquid entrainment in a horizontal tee with a vertical-up branch

This article describes a comprehensive literature review of liquid entrainment in horizontal pipes with vertical-up branches. Deficiencies in the available data and correlations were identified. The Air–water Test Loop for Advanced Thermal–hydraulic Studies (ATLATS) was constructed and entrainment onset and steady-state data were collected for a wide range of flow conditions. Using new insights gained from experimental testing, the authors developed a model for predicting the onset of entrainment and steady-state entrainment rate. Previously published correlations, along with the new model, are compared against all available data. The new model shows very good agreement with the onset data, but is not very good at predicting branch quality at high liquid flow rates.     

Combined effects of clay modifications and compatibilizers on the formation and physical properties of melt‐mixed polypropylene/clay nanocomposites

The melt mixing technique was used to prepare various polypropylene (PP)‐based (nano)composites. Two commercial organoclays (denoted 20A and 30B) served as the fillers for the PP matrix, and two different maleated (so‐called) compatibilizers (denoted PP‐MA and SMA) were employed as the third component. The results from X‐ray diffraction (XRD) and transmission electron microscope (TEM) experiments revealed that 190 °C was an adequate temperature for preparing the nanocomposites. Nanocomposites were achieved only if specific pairs of organoclay and compatibilizer were simultaneously incorporated in the PP matrix. For example, PP/20A(5 wt %)/PP‐MA(10 wt %) and PP/30B(5 wt %)/SMA(5 wt %) composites exhibited nanoscaled dispersion of 20A or 30B in the PP matrix. Differential scanning calorimetry (DSC) results indicated that the organoclays served as nucleation agents for the PP matrix. Generally, their nucleation effectiveness increased with the addition of compatibilizers. The thermal stability enhancement of PP after adding 20A was confirmed with thermogravimetric analysis (TGA). The enhancement became more evident as a suitable compatibilizer was further added. However, for the 30B‐included composites, thermal stability enhancement was not evident. The dynamic mechanical properties (i.e., storage modulus and loss modulus) of PP increased as the nanocomposites were formed; the properties increment corresponded to the organoclay dispersion status in the matrix. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4139–4150, 2004