90°分束偏光镜光强分束比研究

给出了90°分束偏光镜的e,o光光强分束比的计算公式,以及光强分束比随光波长的变化曲线;在6328Å测得的光强分束比与计算值是一致的。     

COIL中BHP浓度对发生O_2(~1△)的影响

本文实验研究了BHP的浓度对产生O2（1△）的影响。实验结果表明：当BHP浓度大于3.5M时，Cl2利用率以及O2（1△）的产率将不依赖于BHP浓度的变化而变化，同时，实验结果表明，使用低浓度的BHP对COIL的操作是可行的。     

Poly(phenylene vinylene)‐based copolymers containing 3,7‐phenothiazylene and 2,6‐pyridylene chromophores: Fluorescence sensors for acids,metal ions,and oxidation

A novel copolymer, poly(N‐hexyl‐3,7‐phenothiazylene‐1,2‐ethenylene‐2,6‐pyridylene‐1,2‐ethenylene) ( P3 ), containing N‐hexyl‐3,7‐phenothiazylene and 2,6‐pyridylene chromophores was synthesized to investigate the effect of protonation, metal complexation, and chemical oxidation on its absorption and photoluminescence (PL). Poly(N‐hexyl‐3,8‐iminodibenzyl‐1,2‐ethenylene‐1,3‐phenylene‐1,2‐ethenylene) and poly(N‐hexyl‐3,7‐phenothiazylene‐1,2‐ethenylene‐1,3‐phenylene‐1,2‐ethenylene) ( P2 ), consisting of 1,3‐divinylbenzene alternated with N‐hexyl‐3,8‐iminodibenzyl and N‐hexyl‐3,7‐phenothiazylene, respectively, were also prepared for comparison. Electrochemical investigations revealed that P3 exhibited lower band gaps (2.34 eV) due to alternating donor and acceptor conjugated units (push–pull structure). The absorption and PL spectral variations of P3 were easily manipulated by protonation, metal chelation, and chemical oxidation. P3 displayed significant bathochromic shifts when protonated with trifluoroacetic acid in chloroform. The complexation of P3 with Fe³⁺ led to a significant absorption change and fluorescence quenching, and this implied the coordination of ferric ions with the 2,6‐pyridylene groups in the backbone. Moreover, both phenothiazylene‐containing P2 and P3 showed conspicuous PL quenching with a slight redshift when oxidized with NOBF₄. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1272–1284, 2004     

Investigation on crosslinking behaviors of NBR/PVC filled with anhydrous copper sulfate particles by dynamic mechanical analysis

Crosslinking behaviors of acrylonitrile butadiene rubber (NBR)/poly (vinyl chloride) (PVC) alloy, filled with anhydrous copper sulfate (CuSO₄) particles, were investigated for the first time by dynamic mechanical analysis (DMA) under hetero and isothermal modes, respectively. In the heterothermal testing, (NBR/PVC)/CuSO₄ compound showed two marked increases in the storage modulus (E′), corresponding to coordination crosslinking of NBR-CuSO₄ and self-crosslinking of NBR and PVC respectively. During the isothermal testing, a dramatic increase in E′ was found at the initial stage while that of original NBR/PVC alloy was not detected. The marked increase in E′ of (NBR/PVC)/CuSO₄ compound was mainly due to the crosslinking induced by coordination between  CN and Cu²⁺. The increasing extent of E′ increased with the rise of CuSO₄ content, suggesting the formation of a greater number of crosslinks. Moreover, the activation energy (E_a) of crosslinking process was about 139 kJ/mol. In this work, fourier transform infrared spectrum (FT-IR) and equilibrium swelling method were also performed for the characterization of the compound. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 41–51, 2007     

On existence of solutions for some hyperbolic-parabolic-type chemotaxis systems

In this paper, we discuss the local and global existence ofweak solutions for some hyperbolic–parabolic systems modellingchemotaxis.     

Solvothermal synthesis of TiO2: anatase nanocrystals and rutile nanofibres from TiCl4 in acetone

This work reports a new synthetic approach for single‐phase TiO₂ nanomaterials by solvothermal treatment of titanium tetrachloride in acetone at 80–110 °C. Small, uniform, and yet size‐tunable (5–10 nm) anatase titania nanocrystallites were obtained using a low concentration of TiCl₄ in acetone (i.e., at molar ratios of TiCl₄/acetone ≤ 1:15) in the temperature range of 80–110 °C, while rutile nanofibers were synthesized using a high concentration of TiCl₄ (e.g., TiCl₄/acetone = 1:10) at 110 °C. Copyright © 2007 John Wiley & Sons, Ltd.     

Improved coupled-mode theory of anisotropic optical waveguides

A coupled-mode equation for anisotropic waveguide systems of arbitrary cross section and general dielectric distribution is derived. Numerical results comparing the exact calculations to those of the method of Hardy et al. (Opt. Lett., vol.11, 742-4, 1986) show that the same accuracy can be obtained not only for TE, but also for TM mode coupling in the case of anisotropic waveguides, and the improved coupled-mode theory is applicable to the situation when moderately strong coupling occurs under the condition where the edge-to-edge separation of two coupled guides D₂ is about 0.1 μm     

Viscometric properties of dilute polystyrene/dioctyl phthalate solutions

We report viscometric data collected in a Couette rheometry on dilute, single‐solvent polystyrene (PS)/dioctyl phthalate (DOP) solutions over a variety of polymer molecular weights (5.5 × 10⁵ ≤ M_w ≤ 3.0 × 10⁶ Da) and system temperatures (288 K ≤ T ≤ 318 K). In view of the essential viscometric features, the current data may be classified into three categories: The first concerns all the investigated solutions at low shear rates, where the solution properties are found to agree excellently with the Zimm model predictions. The second includes all sample solutions, except for high‐molecular‐weight PS samples (M_w ≥ 2.0 × 10⁶ Da), where excellent time–temperature superposition is observed for the steady‐state polymer viscosity at constant polymer molecular weights. No similar superposition applies at a constant temperature but varied polymer molecular weights, however. The third appears to be characteristic of dilute high‐molecular‐weight polymer solutions, for which the effects of temperature on the viscosity curve are further complicated at high shear rates. The implications concerning the relative importance of hydrodynamic interactions, segmental interactions, and chain extensibility with increasing polymer molecular weight, system temperature, and shear rate are discussed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 787–794, 2006     

Economic analysis and optimization of tool portfolio in semiconductor manufacturing

The tool portfolio of a plant refers to the makeup, in quantity and type, of processing machines in the plant. It is determined by taking into consideration the future trends of process and machine technologies and the forecasts of product evolution and product demands. Portfolio planning is also a multicriteria decision-making task involving tradeoffs among, investment cost, throughput, cycle time, and risk. Tool portfolio planning is a complex task that has strong bearing on manufacturing efficiency. In the first part of this paper, a multicriteria economic decision model is presented for optimal configuration. of the portfolio and to determine the optimal factory loading. The second and third parts of the paper contain applications of the model. If plants are closely located or have a twin-plant design, portfolio planning at multiple plants can be integrated to enhance the overall effectiveness of portfolios. In the second part, a novel methodology for arbitrating capacity backup between plants is described. Because the economic model is constructed upon a valuation of both cycle time and throughput, it is a suitable method for the evaluation of cycle time reduction projects. The application procedure is outlined in the third part.