Descriptive Complexity and Reflective Properties of Combinatorial Configurations

We study the Ramsey theoretic properties of combinatorial configurationswhich are generated by infinite binary strings which are randomin the sense of Kolmogorov-Chaitin.     

Direct imaging of a high-power diode laser cavity using a transparent indium-tin-oxide (ITO) contact

We describe a novel "see-through" indium-tin-oxide contact on the n-side of a high power unstable resonator semiconductor laser (URSL) that allows direct observation of the cavity during high power operation. Under optimized annealing conditions this transparent ITO contact has a low enough specific contact resistivity to permit normal high power CW operation of the URSL and allows the observation of filamentation. This contact scheme is applicable to a wide range of semiconductor lasers and is especially appropriate for high power devices. The same structure can also be used to obtain a 2-D thermal map of the laser cavity.     

Elimination of phase noise of pulsed laser diodes in electroopticsampling systems

The multimode operation of pulsed laser diode sources is converted into excess noise in electrooptic probing systems for electrical waveforms and prevents measurements with shot-noise-limited sensitivity. The transfer function of the sampling system is determined and analyzed in terms of the wavelength and electric field dependence. It is shown that by proper orientation of the polarizing components within the optical beam path, points of operation can by found which have both a vanishing wavelength dependence of the transfer function and maximum sensitivity to the electric fields to be measured. Excess noise sources due to wavelength fluctuations of the laser are thus eliminated, and shot-noise-limited voltage resolution is obtained. The system has been optimized to yield a voltage sensitivity of 2.3 mV/√Hz for a longitudinal LiNbO₃ probe crystal     

Training analysis of adaptive interference suppression fordirect-sequence code-division multiple-access systems

This paper studies the transient behavior of an adaptive near-far resistant receiver for direct-sequence (DS) code-division multiple-access (CDMA) known as the minimum mean-squared error (MMSE) receiver. This receiver structure is known to be near-far resistant and yet does not require the large amounts of side information that are typically required for other near-far resistant receivers. In fact, this receiver only requires code timing on the one desired signal. The MMSE receiver uses an adaptive filter which is operated in a manner similar to adaptive equalizers. Initially there is a training period where the filter locks onto the signal that is sending a known training sequence. After training, the system can then switch to a decision-directed mode and send actual data. This work examines the length of the training period needed as a function of the number of interfering users and the severity of the near-far problem. A standard least mean-square (LMS) algorithm is used to adapt the filter and so the trade-off between convergence and excess mean-squared error is studied. It is found that in almost all cases a step size near 1.0/(total input power) gives the best speed of convergence with a reasonable excess mean-squared error. Also, it is shown that the MMSE receiver can tolerate a 30-40 dB near-far problem without excessively long convergence time     

Generalized impedance control of robot for assembly tasks requiringcompliant manipulation

To perform assembly tasks requiring compliant manipulation, the robot must follow a motion trajectory and exert an appropriate force profile while making compliant contact with a dynamic environment. For this purpose, a generalized impedance in the task space consisting of a second-order function relating the motion errors and interaction force errors is introduced such that the contact force can be commanded and controlled. With generalized impedance control, the robot can behave with a desired dynamic characteristic when it interacts with the environment. To ensure the success of the assembly, a strategy during task planning which takes into consideration the interrelation between motion and force trajectories as well as contact compliance is introduced. The generalized impedance control method is applied to the prismatic joint of a selective compliance assembly robot arm (SCARA) robot for inserting a printed circuit board (PCB) into an edge connector socket. Depending on the progress of the parts joining operation, various amount of interaction forces are generated which have to be accommodated. It is demonstrated that an assembly strategy which consists of a sequence of carefully planned target impedance can enable the task to be executed in a desirable manner. The effectiveness of this approach is illustrated through experiments by comparing the results with those obtained using a well-established position control scheme as well as the original impedance control method     

Theory of soliton stability in asynchronous modelocking

A new type of fiber laser modelocking is examined where a phase modulator is driven asynchronously with respect to a harmonic of the roundtrip cavity frequency. An asynchronous drive is able to produce high repetition rate (>1 GHz) soliton pulses that are shorter than the classic, active modelocking pulse width limit. It is shown that with a proper choice of fiber parameters, noise cleanup and soliton pulse shaping can be obtained using filtering and asynchronous phase modulation. Limits of asynchronous detuning are derived and a comparison with the parameters ranges for synchronous phase modulation is also presented     

Bit error simulation for π/4 DQPSK mobile radio communicationsusing two-ray and measurement-based impulse response models

An accurate software/hardware bit-by-bit error simulator for mobile radio communications is described. Simulation results in indoor and outdoor channels are compared with theoretical results. Bit error rate (BER) results in simulated frequency-selective fading channels generated by several channel models such as two-ray, constant amplitude, and simulated indoor radio channel impulse models (SIRCIMs) are presented. It is shown that BER is not only dependent on the RMS delay spread, but also on the distribution of temporal and spatial multipath components in local areas. An important result is that a two-ray Rayleigh fading model is a poor fit for indoor wireless channels and, if used, can underestimate the BER by orders of magnitude. A real-time bit error simulation of video transmission using the bit-by-bit error simulator is described. The simulator, called BERSIM, is shown to be a useful tool for evaluating emerging data transmission products for digital mobile communications     

Electroluminescence from phenylenevinylene-based polymer blends

The electroluminescent behaviour of films of poly(phenylphenylenevinylene) (PPPV), of PPPV blended with polystyrene (PS) and of PS doped with oligo(phenylenevinylene) sandwiched between indium–tin oxide (ITO) and Al contacts has been investigated. Polymer blending increases the relative quantum efficiency by up to two orders of magnitude. Studying the cell performance under application of rectangular voltage pulses as a function of temperature indicates that (i) hole injection at the ITO contact occurs by tunnelling, (ii) tunnel injection of electrons at the cathode is promoted by a space charge field across an interfacial Al₂O₃ layers and (iii) leakage of holes through the cathodic barrier is the main loss mechanism for holes.     

WIPL: a program for electromagnetic modeling of composite-wire andplate structures

WIPL is a program which allows fast and accurate analysis of antennas. The geometry of any metallic structure (even a very large structure) is defined as a combination of wires and plates. WIPL's analysis features include evaluations of the current distribution, near and far field, and impedance, admittance and s-parameters. The program uses an entire-domain Galerkin method. Efficiency of the program is based on the flexible geometrical model, and sophisticated basis functions. In this paper, the basic theory implemented in the program, and some results concerning TV UHF panel antennas and large horn antennas are given