Fabrication of 1.55 μm VCSELs on Si using metallic bonding

Using AuGeNiCr multilayered metals as the wafer bonding medium, long-wavelength GaInAsP/InP vertical cavity surface emitting lasers employing Al-oxide/Si as the upper and lower distributed Bragg reflectors were fabricated on Si substrate with the bonding interface formed outside the vertical cavity surface emitting laser cavity. Laser emission at 1.545 μm was measured under pulsed operations near room temperature. The low-temperature metallic bonding process demonstrates a great potential in device fabrication     

Retrievals of column water vapor using millimeter-wave radiometric measurements

The airborne Millimeter-wave Imaging Radiometer (MIR) measurements conducted over the Midwest region of the continental United States during January/February 1997 and over the Alaska-Arctic region during May 1998 are used to estimate column water vapor W<0.8 g/cm/sup 2/ under a clear sky. On board the same aircraft are two other instruments, the Cloud Lidar System (CLS) and MODerate-resolution Imaging Spectrometer (MODIS) Airborne Simulator (MAS), which provide cloud cover information and independent measurements of W, respectively. The MIR-estimated W values are compared and found to be in very good agreement with those measured by rawinsondes at near concurrence. A close correlation is found between the MIR-estimated W and that estimated from the MAS near-IR reflectance ratios. Water surface emissivities at several MIR frequencies are obtained in the process of the W retrieval from several flights over the Midwest lakes. These estimated emissivities compared favorably with values calculated for a calm water surface, which are based on a di-electric permittivity model and MAS-measured surface temperatures. The results from all comparisons strongly demonstrate the soundness of the technique for estimating W.     

A STRASSEN LAW OF THE ITERATED LOGARITHM FOR PROCESSES WITH INDEPENDENT INCREMENT

ＡＳＴＲＡＳＳＥＮＬＡＷＯＦＴＨＥＩＴＥＲＡＴＥＤＬＯＧＡＲＩＴＨＭＦＯＲＰＲＯＣＥＳＳＥＳＷＩＴＨＩＮＤＥＰＥＮＤＥＮＴＩＮＣＲＥＭＥＮＴＷａｎｇＪｉａｇａｎｇＡｂｓｔｒａｃｔＬｅｔＸ＝｛Ｘ（ｔ），ｔ０｝ｂｅａｐｒｏｃｅｓｗｉｔｈｉｎｄｅｐ...     

Alloying by high dose ion implantation of iron into magnesium and aluminium

Alloys of the systems Fe–Al (mixable over the whole concentration range) and Fe–Mg (insoluble with each other) were produced by implantation of Fe ions into Al and Mg, respectively. The implantation energy was 200 keV and the ion doses ranged from 1 × 10₁₄ to 9 × 10₁₇cm^-2The obtained implantation profiles were determined by Auger electron spectroscopy depth profiling. Maximum iron concentrations reached were up to 60 at.% for implantation into Al and 94 at.% for implantation into Mg. Phase analysis of the implanted layers was performed by conversion electron Mössbauer spectroscopy and X‐ray diffraction. For implantation into Mg, two different kinds of Mössbauer spectra were obtained: at low doses paramagnetic doublets indicating at least two different iron sites and at high doses a dominant ferromagnetic six‐line‐pattern with a small paramagnetic fraction. The X‐ray diffraction pattern concluded that in the latter case a dilated αiron lattice is formed. For implantation into Al, the Mössbauer spectra were doublet structures very similar to those obtained at amorphous Fe–Al alloys produced by rapid quenching methods. They also indicated at least two different main iron environments. For the highest implanted sample a ferromagnetic six‐line‐pattern with magnetic field values close to those of Fe₃Al appeared.     

A fully soft-switched extended-period quasi-resonantpower-factor-correction circuit

This paper presents the design criteria, procedure, and implementation of a soft-switched power-factor-correction (PFC) circuit based on the extended-period quasi-resonant (EPQR) principles. All power electronic devices including switches and diodes in the circuit are fully soft switched. The design method is demonstrated in a prototype circuit. The operating principles are confirmed with computer simulation and experimental results. A comparison of the EP-QR operation and zero-voltage-transition (ZVT) pulse-width modulation (PWM) method     

The strategy of edge wear prediction in CIM concept

A monitoring of tool wear in different cutting operations has been studied for many years. Special techniques have been used to detect a wear status basing upon cutting forces, acoustic emission, temperature, torque and power, vibration, noise and acceleration sensors. The adapting of a proper prediction method allows to solve problems of an automatic supervision in Computer Integrated Manufacturing systems. A task of the abrasive edge wear index prediction can be formulated as follows: disposing by the data collection of the edge wear status in a time period preceding the concerning the wear status in the successive time period embraced by the prediction method.     

Densification involved in the UV-based photosensitivity of silicaglasses and optical fibers

A comprehensive survey of photosensitivity in silica glasses and optical fiber is reviewed. Recent work on understanding the mechanisms contributing to germanium or aluminum doped fiber photosensitivity is discussed within the framework of photoelastic densification models     

Brennstoffzellen

For two applications of fuel cells (SOFC and IMFC) system configurations and energy balances are presented. A decentralized combined heat and power plant on SOFC basis can be designed as a flexible system with high efficiency. A drive system with methanol reformer and fuel cell (IMFC) in comparison with a natural gas combustion engine has lower energy comsumption and much lower emissions.