Study of the charge-exchange reactions\pi ^ - p \to (\pi ^0 ,\eta ,\eta \prime )n at 63 GeV

Muon electron pairs were detected in an Al multiplate spark chamber, exposed to a neutrino beam from the CERN PS. The leptons were not accompanied by other particles, except occasionally by protons. The background came mainly from muon associated π⁰ production, with one decay gamma lost. It was determined empirically, together with the small contribution from υ _e reactions. For electron energies above 2 GeV the background is 5.7±1.5 events, whereas 18 (μe)-candidates have been observed. Hence the effect is established, with a rate of about 10^?4 as compared to the muonic reactions above 3 GeV. Charm creation as the origin of this (μe)-production process is excluded; heavy neutral lepton production does not fit the kinematics observed. Instead the events are compatible with the two-body decay of an object with variable invariant mass of order 1 GeV, possibly resulting from axion interactions.     

A comparison of steady-state evoked potentials to modulated tones in awake and sleeping humans.

Steady-state evoked potential responses were measured to binaural amplitude-modulated (AM) and combined amplitude- and frequency-modulated (AM/FM) tones. For awake subjects, AM/FM tones produced larger amplitude responses than did AM tones. Awake and sleeping responses to 30-dB HL AM/FM tones were compared. Response amplitudes were lower during sleep and the extent to which they differed from awake amplitudes was dependent on both carrier and modulation frequencies. Background EEG noise at the stimulus modulation frequency was also reduced during sleep and varied with modulation frequency. A detection efficiency function was used to indicate the modulation frequencies likely to be most suitable for electrical estimation of behavioral threshold. In awake subjects, for all carrier frequencies tested, detection efficiency was highest at a modulation frequency of 45 Hz. In sleeping subjects, the modulation frequency regions of highest efficiency varied with carrier frequency. For carrier frequencies of 250 Hz, 500 Hz, and 1 kHz, the highest efficiencies were found in two modulation frequency regions centered on 45 and 90 Hz. For 2 and 4 kHz, the highest efficiencies were at modulation frequencies above 70 Hz. Sleep stage affected both response amplitude and background EEG noise in a manner that depended on modulation frequency. The results of this study suggest that, for sleeping subjects, modulation frequencies above 70 Hz may be best when using steady-state potentials for hearing threshold estimation.     

Estimation of multivariate binary density using orthogonal functions

In this paper, the authors studied certain properties of the estimate of Liang and Krishnaiah (1985, J. Multivariate Anal. 16, 162–172) for multivariate binary density. An alternative shrinkage estimate is also obtained. The above results are generalized to general orthonormal systems.     

Effects of annealing conditions on the electrical properties of Bi4-xNdxTi3O12 (x = 0.46) thin films processed at low temperature

Neodymium-substituted Bi₄Ti₃O₁₂ (BNdT) thin films were prepared by a chemical solution deposition technique on platinum- coated silicon substrates. All of the samples were annealed at the relatively low temperature of 600 °C by a rapid thermal annealing process in different atmospheres, such as O₂, air, and nitrogen, and vacuum. Irrespective of different annealing atmospheres, all of the BNdT thin films exhibit good ferroelectric properties, such as a saturated hysteresis loop, good fatigue endurance, and low leakage current density. A large remanent polarization (P_r) of ∼48 μC/cm² with an electric field of 240 kV/cm was observed from the BNdT thin film annealed in O₂ atmosphere. The BNdT thin films annealed in nitrogen and vacuum, at reduced oxygen partial pressures, exhibit smaller P_r than that annealed in oxygen. The difference of P_r of the BNdT thin films annealed in different atmospheres may originate from differences in the grain sizes and the number of oxygen vacancies. PACS 77.55.+f; 77.80.-e; 77.80.Fm; 81.15.-z     

Reliability prediction models to support conceptual design

During the early stages of conceptual design, the ability to predict reliability is very limited. Without a prototype to test in a lab environment or without field data, component failure rates and system reliability performance are usually unknown. A popular method for early reliability prediction is to develop a computer model for the system. However, most of these models are extremely specific to an individual system or industry. This paper presents three general procedures (using both simulation and analytic solution techniques) for predicting system reliability and average mission cost. The procedures consider both known and unknown failure rates and component-level and subsystem-level analyzes. The estimates are based on the number of series subsystems and redundant (active or stand-by) components for each subsystem. The result is a set of approaches that engineers can use to predict system reliability early in the system-design process. Software was developed (and is discussed in this paper) that facilitates the application of the simulation-based techniques. For the specific type of system and mission addressed in this paper, the analytic approach is superior to the simulation-based prediction models. However, all three approaches are presented for two reasons: (1) to convey the development process involved with building these prediction tools; and (2) the simulation-based approaches are of greater value as the research is extended to consider more complex systems and scenarios     

Adaptive mutation parameter toggling genetic algorithm for phase-only array synthesis

A genetic algorithm that speeds convergence for phased array phase-only synthesis by adaptively toggling between nine mutation parameter pairs is illustrated. This adaptive algorithm outperforms any of the corresponding nine static cases where these same mutation parameters are held constant throughout the optimisation process.     

Solid-phase epitaxy of CaSi2 on Si(1 1 1) and the Schottky-barrier height of CaSi2/Si(1 1 1)

Thin Ca films were evaporated on Si(1 1 1) under UHV conditions and subsequently annealed in the temperature range 200–650 °C. The interdiffusion of Ca and Si was examined by ex situ Auger depth profiling. In situ monitoring of the Si 2p core-level shift by X-ray photoemission spectroscopy (XPS) was employed to study the silicide formation process. The formation temperature of CaSi₂ films on Si(1 1 1) was found to be about 350 °C. Epitaxial growth takes place at T≥400 °C. The morphology of the films, measured by atomic force microscopy (AFM), was correlated with their crystallinity as analyzed by X-ray diffraction (XRD). According to measurements of temperature-dependent I–V characteristics and internal photoemission the Schottky-barrier height of CaSi₂ on Si(1 1 1) amounts to qΦ_Bn=0.25 eV on n-type and to qΦ_Bp=0.82 eV on p-type silicon.     

Compact integration operators for Fréchet-space-valued measures

Many operators in Banach spaces occur as the integration operator of a suitable vector measure; their compactness is completely described in [19]. However, many important spaces X in analysis (and integration operators in such spaces) do not fall into this scheme because X is not normable. Characterizing the compactness of integration operators in this setting is the aim of this note. The methods and techniques employed are quite different to the Banach space arguments used in [19].