Alloying by high dose ion implantation of iron into magnesium and aluminium

Alloys of the systems Fe–Al (mixable over the whole concentration range) and Fe–Mg (insoluble with each other) were produced by implantation of Fe ions into Al and Mg, respectively. The implantation energy was 200 keV and the ion doses ranged from 1 × 10₁₄ to 9 × 10₁₇cm^-2The obtained implantation profiles were determined by Auger electron spectroscopy depth profiling. Maximum iron concentrations reached were up to 60 at.% for implantation into Al and 94 at.% for implantation into Mg. Phase analysis of the implanted layers was performed by conversion electron Mössbauer spectroscopy and X‐ray diffraction. For implantation into Mg, two different kinds of Mössbauer spectra were obtained: at low doses paramagnetic doublets indicating at least two different iron sites and at high doses a dominant ferromagnetic six‐line‐pattern with a small paramagnetic fraction. The X‐ray diffraction pattern concluded that in the latter case a dilated αiron lattice is formed. For implantation into Al, the Mössbauer spectra were doublet structures very similar to those obtained at amorphous Fe–Al alloys produced by rapid quenching methods. They also indicated at least two different main iron environments. For the highest implanted sample a ferromagnetic six‐line‐pattern with magnetic field values close to those of Fe₃Al appeared.     

A fully soft-switched extended-period quasi-resonantpower-factor-correction circuit

This paper presents the design criteria, procedure, and implementation of a soft-switched power-factor-correction (PFC) circuit based on the extended-period quasi-resonant (EPQR) principles. All power electronic devices including switches and diodes in the circuit are fully soft switched. The design method is demonstrated in a prototype circuit. The operating principles are confirmed with computer simulation and experimental results. A comparison of the EP-QR operation and zero-voltage-transition (ZVT) pulse-width modulation (PWM) method     

The strategy of edge wear prediction in CIM concept

A monitoring of tool wear in different cutting operations has been studied for many years. Special techniques have been used to detect a wear status basing upon cutting forces, acoustic emission, temperature, torque and power, vibration, noise and acceleration sensors. The adapting of a proper prediction method allows to solve problems of an automatic supervision in Computer Integrated Manufacturing systems. A task of the abrasive edge wear index prediction can be formulated as follows: disposing by the data collection of the edge wear status in a time period preceding the concerning the wear status in the successive time period embraced by the prediction method.     

Densification involved in the UV-based photosensitivity of silicaglasses and optical fibers

A comprehensive survey of photosensitivity in silica glasses and optical fiber is reviewed. Recent work on understanding the mechanisms contributing to germanium or aluminum doped fiber photosensitivity is discussed within the framework of photoelastic densification models     

Brennstoffzellen

For two applications of fuel cells (SOFC and IMFC) system configurations and energy balances are presented. A decentralized combined heat and power plant on SOFC basis can be designed as a flexible system with high efficiency. A drive system with methanol reformer and fuel cell (IMFC) in comparison with a natural gas combustion engine has lower energy comsumption and much lower emissions.     

Wave-oriented signal processing of dispersive time-domainscattering data

Phase-space data processing is receiving increased attention because or its potential for furnishing new discriminants relating to classification and identification of targets and other scattering environments. Primary emphasis has been on time-frequency processing because of its impact on transient, especially wideband, short-pulse excitations. Here, we investigate the windowed Fourier transform, the wavelet transform, and model based superresolution algorithms within the context of a fully quantified and calibrated test problem investigated by us previously: two-dimensional (2-D) short-pulse plane wave scattering by a finite periodic array of perfectly conducting coplanar flat strips. Because the forward problem has been fully calibrated and parametrized, some quantitative measures can be assigned with respect to the tradeoffs of these time-frequency algorithms, yielding tentative performance assessments of the tested processing algorithms     

State of and prospects for XeF(C−A) optically pumped lasers

Experimental and theoretical results are presented on an XeF(C?A) blue-green laser driven by 5-kJ energy. The laser was pumped by a ferrite-induced discharge of 90 cm in length. The output energy of 0.22 J was obtained with a plane-parallel resonator. A program to simulate laser operation has been developed. Numerical results for a wide range of conditions are compared with experiments performed by us and by other authors. It is found that intracavity refractive losses limit laser operation for XeF pressures above 3 torr. The laser efficiency strongly depends on the discharge-to-cavity length ratio. Possible ways to increase the laser power and efficiency are discussed.     

Electrical linewidth test structures fabricated in monocrystallinefilms for reference-material applications

The physical widths of reference features incorporated into electrical linewidth test structures patterned in films of monocrystalline silicon have been determined from Kelvin voltage measurements. The films in which the test structures are patterned are electrically insulated from the bulk-silicon substrate by a layer of silicon dioxide provided by SIMOX (Separation by the IMplantation of OXygen) processing. The motivation is to facilitate the development of linewidth reference materials for critical-dimension (CD) metrology-instrument calibration. The selection of the (110) orientation of the starting silicon and the orientation of the structures' features relative to the crystal lattice enable a lattice-plane-selective etch to generate reference-feature properties of rectangular cross section and atomically planar sidewalls. These properties are highly desirable for CD applications in which feature widths are certified with nanometer-level uncertainty for use by a diverse range of CD instruments. End applications include the development and calibration of new generations of CD instruments directed at controlling processes for manufacturing devices having sub-quarter-micrometer features