Coercivity analysis in R17Fe83−χBχ magnets

We studied the coercivity in magnets of composition R₁₇Fe_83−χB_χ (R = Nd, Pr and χ = 8, 30), using measurements of the coercive field H_c, its angular dependence, and the magnetic viscosity coefficient S_v, for temperatures between 4.2 and 500 K. The results are discussed in relation to a model which does not specifically consider the detailed mechanisms involved in magnetization reversal, but which provides information about the magnetic properties in the activation volume v where magnetization reversal is initiated. It is concluded that the ordering temperature in v tends to be slightly smaller than in the bulk and that the room temperature anisotropy in v is not strongly reduced with respect to the bulk value. Finally, a direct evaluation of the dipolar interactions is in good agreement with results obtained from H_c(T).     

X-ray scattering studies of the structure of aqueous hydroxy-propylcellulose solutions

X-ray diffraction studies have been undertaken on aqueous solutions of hydroxy propylcellulose (HPC) over a wide range of the scattering vector Q. The experiments revealed only modest differences in local structure on a distance scale ca. 5–300 Å despite the fact that they covered concentrations generally interpreted as ranging from the isotropic (35.1 wt %) to the anisotropic liquid crystalline (LC) phase (53.5 wt %). Several models were used to interpret the small-angle scattering data, and each gave similar structural parameters and extrapolated intensities ( Q → 0) for both solutions. Peaks were observed with d-spacings ca. 12–17 Å in both materials. Wide-angle x-ray scattering (WAXS) showed slightly increased local order over a size range ca. 5–20 Å for the anisotropic solution, and this is consistent with a greater intensity of the 13 Å peak in this material. It is difficult to reconcile these findings with an interpretation of the LC state involving major differences with the isotropic phase and a high degree of orientational order extending over long length scales.     

Is layering, harmful? [remote procedure call]

Remote procedure call (RPC) mechanisms over the US Department of Defense transmission control protocol. (TCP) can produce behavior analogous to the silly window syndrome because of a mismatched interface between the socket and the TCP modules. The detection and diagnosis of the problem are addressed. Some pointers to a design approach that could avoid the problems of mismatched communication layers are provided     

A versatile leaky-wave antenna based on stub-loaded rectangularwaveguide .I. Theory

A new leaky-wave antenna is presented that possesses many desirable features and is suitable for application to both the millimeter-wave and microwave ranges. These desirable features, some of which are unusual, include a simple configuration, a wide flexibility in the range of available beamwidths, the ability to control the beamwidth and the direction of the beam essentially independently, and negligible cross polarization at all scan angles. The antenna structure consists of a parallel-plate stub guide of small height, less than a half wavelength, located off center on the top of rectangular waveguide. The beamwidth is easily controlled from very wide to very narrow by adjusting the stub width or location. The article presents the principle of operation and the theory, employing a new transverse equivalent network that is accurate, but also simple, so that it permits rapid and inexpensive numerical calculations     

0.27-dB/km attenuation achieved by MSP preform process [opticalfibers]

Mechanically shaped preforms (MSP) have been demonstrated to combine economic non-CVD (chemical vapor deposition) processing and low loss, with a published value of 0.63 dB/km and a size of 30 fkm/preform. Improved processing is proposed which results in a minimum loss of 0.27 dB/km at 1550 nm. Preforms capable of yielding 150 fkm have been produced. Reboiling during preform stretching and fiber pulling is identified as the last remaining problem of the process     

The performance of depressed-cladding single-mode fibers withdifferent b/a ratios

Depressed-cladding single-mode fibers with a first cladding-to-core ratio (b/a) ranging from seven to one and relative refractive-index differences of the core from 0.25 to 0.35% and of the cladding from 0 to -0.2% are investigated experimentally with respect to the LP₁₁ mode cutoff properties, the mode-field diameter, the dispersion, and the bending attenuation. Numerical calculations based on actual profile parameters of the bend loss and the mode-field diameter agree well with experiment. It is demonstrated that low attenuation and bend losses independent of b/a can be obtained if the cutoff wavelength is kept constant by adjusting the core radius, the core index or the index of the first cladding