不同磁路电子回旋共振离子源引出实验

空间推进所用的电子回旋共振离子源(ECRIS)应具有体积小、效率高的特点. 本文研究的ECRIS使用永磁体环产生磁场, 有效减小了体积, 该离子源利用微波在磁场中加热电子, 电子与中性气体发生电离碰撞产生等离子体. 磁场在微波加热电子的过程中起关键作用, 同时影响离子源内等离子体的约束和输运. 通过比较四种磁路结构离子源的离子电流引出特性来研究磁场对10 cm ECRIS性能的影响. 实验发现: 在使用氩气的条件下, 特定结构的离子源可引出160 mA的离子电流, 最高推进剂利用率达60%, 最小放电损耗为120 W·A^-1; 所有离子源均存在多个工作状态, 工作状态在微波功率、气体流量、引出电压变化时会发生突变. 离子源发生状态突变时的微波功率、气体流量的大小与离子源内磁体的位置有关. 通过比较不同离子源的引出离子束流、放电损耗、气体利用率、工作稳定性的差异, 归纳了磁场结构对此种ECRIS引出特性的影响规律, 分析了其中的机理. 实验结果表明: 保持输入微波功率、气体流量、引出电压不变时, 增大共振区的范围、减小共振区到栅极的距离, 离子源能引出更大的离子电流; 减小共振区到微波功率入口、气体入口的距离能降低维持离子源高状态所需的最小微波功率和最小气体流量, 提高气体利用率, 但会导致放电损耗增大. 研究结果有助于深化对此类离子源工作过程的认识, 为其设计和性能优化提供参考.     

甚高频激发容性耦合氩等离子体的电子能量分布函数的演变

甚高频激发的容性耦合等离子体由于离子通量和能量的相对独立可控而受到人们的关注. 本文采用朗缪尔探针诊断技术测量了40.68 MHz激发的容性耦合Ar等离子体的特性(如电子能量概率分布、电子温度和密度等)随宏观参量的演变情况. 实验结果表明, 电子能量概率分布随着气压的增加从双麦克斯韦分布逐步转变为单麦克斯韦分布并最终演变为Druyvesteyn分布, 而射频激发功率的增加促进了低能电子布居数的增强; 在从等离子体放电中心移向边界的过程中, 低能电子的布居数显著下降, 而高能电子的布居则有所上升; 放电极板间距的变化直接导致了等离子体中电子加热模式的转变. 另外, 我们也对等离子体中的高低能电子密度和温度的分配情况进行了讨论.     

硅单粒子位移损伤多尺度模拟研究

本文结合分子动力学方法和动力学蒙特卡罗方法, 研究了单个粒子入射硅引起的位移损伤缺陷的产生和演化过程; 基于Shockley-Read-Hall理论计算了单个粒子入射引起的位移损伤缺陷导致的泄漏电流增加及其演化过程, 比较了缺陷退火因子与泄漏电流退火因子之间的差异, 并将计算结果与实验值进行了对比. 结果表明, 计算泄漏电流时, 仅考虑一种缺陷的情况下缺陷退火因子与泄漏电流退火因子相同, 考虑两种缺陷类型情况下二者在数值上有所区别, 但缺陷退火因子仍能在一定程度上反映泄漏电流的退火行为. 分子动力学模拟中采用Stillinger-Weber势函数和Tersoff势函数时缺陷退火因子和泄漏电流退火因子与实验结果一致, 基于Stillinger-Weber势函数的计算结果与实验值更为接近.     

Progress of Jinping Underground laboratory for Nuclear Astrophysics (JUNA)

Jinping Underground laboratory for Nuclear Astrophysics(JUNA) will take the advantage of the ultra-low background of CJPL lab and high current accelerator based on an ECR source and a highly sensitive detector to directly study for the first time a number of crucial reactions occurring at their relevant stellar energies during the evolution of hydrostatic stars. In its first phase, JUNA aims at the direct measurements of~(25)Mg(p,γ)~(26)Al,~(19)F(p,α)~(16)O,~(13)C(α,n)~(16)O and ~(12)C(α,γ)~(16)O reactions. The experimental setup,which includes an accelerator system with high stability and high intensity, a detector system, and a shielding material with low background, will be established during the above research. The current progress of JUNA will be given.     

Applications of two-way satellite time and frequency transfer in the BeiDou navigation satellite system

A two-way satellite time and frequency transfer(TWSTFT) device equipped in the BeiDou navigation satellite system(BDS)can calculate clock error between satellite and ground master clock. TWSTFT is a real-time method with high accuracy because most system errors such as orbital error, station position error, and tropospheric and ionospheric delay error can be eliminated by calculating the two-way pseudorange difference. Another method, the multi-satellite precision orbit determination(MPOD)method, can be applied to estimate satellite clock errors. By comparison with MPOD clock estimations, this paper discusses the applications of the BDS TWSTFT clock observations in satellite clock measurement, satellite clock prediction, navigation system time monitor, and satellite clock performance assessment in orbit. The results show that with TWSTFT clock observations, the accuracy of satellite clock prediction is higher than MPOD. Five continuous weeks of comparisons with three international GNSS Service(IGS) analysis centers(ACs) show that the reference time difference between BeiDou time(BDT) and golbal positoning system(GPS) time(GPST) realized IGS ACs is in the tens of nanoseconds. Applying the TWSTFT clock error observations may obtain more accurate satellite clock performance evaluation in the 104 s interval because the accuracy of the MPOD clock estimation is not sufficiently high. By comparing the BDS and GPS satellite clock performance, we found that the BDS clock stability at the 103 s interval is approximately 10.12, which is similar to the GPS IIR.     

Hybrid process for texturization of diamond wire sawn multicrystalline silicon solar cell

Acid texture is difficult for diamond wire sawn (DWS) multicrystalline silicon (mc‐Si) wafer owing to the inhomogeneous distribution of damage layer on the surface. In this article, metal‐assisted chemical etching (MACE) has been selected for introducing a porous seeding layer to induce acid texturing etching. SEM results show that the oval pit structures coverage get obvious improvement even on the smooth areas. Owing to the further improved light absorption ability by second MACE and nanostructure rebuilding (NSR) process, nanostructured DWS mc‐Si solar cell has exhibited a conversion efficiency of 17.96%, which is 0.45% higher than that of DWS wafer with simple acid texture process. (© 2016 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Process-directed self-assembly of multiblock copolymers: Solvent casting <Emphasis Type="Italic">vs</Emphasis> spray coating

Using computer simulation of a soft, coarse-grained model and self-consistent field theory we investigate how collapsed, globular chain conformations in the initial stages of structure formation, which are produced by spray-coating, affect the single-chain structure and morphology of microphase-separated multiblock copolymers. Comparing spray-coated films with films that start from a disordered state of Gaussian chains, we observe that the collapsed molecular conformations in the initial stage give rise to (1) a smaller fraction of blocks that straddle domains (bridges), (2) a significant reduction of the molecular extension normal to the internal interfaces, and (3) a slightly larger lamellar domain spacing in the final morphology. The relaxation of molecular conformations towards equilibrium is very protracted for both processes – solvent casting and spray coating. These findings illustrate that the process conditions of the copolymer materials may significantly affect materials properties (such as mechanical properties) because the system does not reach thermal equilibrium on the relevant time scales.     

Threshold crack speed controls dynamical fracture of silicon single crystals

Fracture experiments of single silicon crystals reveal that after the critical fracture load is reached, the crack speed jumps from zero to approximately 2 km/sec, indicating that crack motion at lower speeds is forbidden. This contradicts classical continuum fracture theories predicting a continuously increasing crack speed with increasing load. Here we show that this threshold crack speed may be due to a localized phase transformation of the silicon lattice from 6-membered rings to a 5-7 double ring at the crack tip.     

Local electronic structure near Mn acceptors in InAs: surface-induced symmetry breaking and coupling to host states

We present low-temperature scanning tunneling spectroscopy measurements on Mn acceptors in InAs in comparison with tight-binding calculations. We find a strong (001)-mirror asymmetry of the bound hole wave function close to the (110) surface. In addition, multiple acceptor-related peaks are observed and are attributed to a spin-orbit splitting of the acceptor level. Because of the p-d exchange interaction the local density of states near the acceptors is enhanced in the valence band and suppressed in the conduction band. We also observe signs of anisotropic scattering of the conduction band states by neutral acceptors.     

Levitation, lift, and bidirectional motion of colloidal particles in an electrically driven nematic liquid crystal

We study electric-field-induced dynamics of colloids in a nematic cell, experimentally and by computer simulations. Solid particles in the nematic bulk create director distortions of dipolar type. Elastic repulsion from the walls keeps the particles in the middle of cell. The ac electric field reorients the dipoles and lifts them to top or bottom, depending on dipole orientation. Once near the walls, the colloids are carried along two antiparallel horizontal directions by nematic backflow. Computer simulations of the backflow agree with the experiment.