BioFET sensor for detection of albumin in urine

Characterisation of a BioFET for detection of albumin in a mixture of human urine is presented. To avoid electrolyte effect of the urine, it was measured in PBS (phosphate buffer saline) at a fixed pH after albumin binding. The drain current was modulated by the albumin bound to the anti-albumin immobilised on the gate surface of the BioFET. The current variation ratio was likely to be proportional to the concentration of the albumin in the range 50-250 mg/1. The results show the feasibility of the BioFET as a urinary albumin sensor.     

Studies on calcium‐containing poly(urethane ether)s

The calcium salt of mono(hydroxyethoxyethyl)phthalate [Ca(HEEP)₂] was synthesized by the reaction of diethylene glycol, phthalic anhydride, and calcium acetate. Calcium‐containing poly(urethane ether)s (PUEs) were synthesized by the reaction of hexamethylene diisocyanate (HMDI) or tolylene 2,4‐diisocyanate (TDI) with a mixture of Ca(HEEP)₂ and poly(ethylene glycol) (PEG₃₀₀ or PEG₄₀₀) with di‐n‐butyltin dilaurate as a catalyst. A series of calcium‐containing PUEs of different compositions were synthesized with Ca(HEEP)₂/PEG₃₀₀ (or PEG₄₀₀)/diisocyanate (HMDI or TDI) molar ratios of 2:2:4, 3:1:4, and 1:3:4 so that the coating properties of the PUEs could be studied. Blank PUEs without calcium‐containing ionic diols were also prepared by the reaction of PEG₃₀₀ or PEG₄₀₀ with HMDI or TDI. The PUEs were well characterized by Fourier transform infrared, ¹H and ¹³C NMR, solid‐state cross‐polarity/magic‐angle‐spinning ¹³C NMR, viscosity, solubility, and X‐ray diffraction studies. The thermal properties of the polymers were also studied with thermogravimetric analysis and differential scanning calorimetry. The PUEs were applied as top coats on acrylic‐coated leather, and their physicomechanical properties were also studied. The coating properties of PUEs, such as the tensile strength, elongation at break, tear strength, water vapor permeability, flexing endurance, cold crack resistance, abrasion resistance, color fastness, and adhesive strength, were better than the standard values. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2865–2878, 2003     

Determination of carbamazepine by chemiluminescence detection using chemically prepared tris(2,2'-bipyridine)ruthenium(III) as oxidant.

A new chemiluminescence method for the determination of carbamazepine (CBZ) has been developed. The method is based on the chemiluminescence produced in the reaction of tris(2,2'-bipyridine)ruthenium(III) and CBZ in an acidic medium. The chemiluminescence intensity was enhanced by organic solvents in the reaction system. Under the optimum experimental conditions, the calibration curve was linear over the range 4.0 x 10(-3)-8.6 x 10(-7) mol/L for CBZ. The detection limit (S/N = 3) was 2.5 x 10(-7) mol/L and the relative standard deviation of six replicate measurements was 2.6% for 4.0 x 10(-4) mol/L of CBZ. The possible reaction mechanism were also discussed. The chemiluminescence method was successfully applied to assay the CBZ contents in pharmaceutical tablets.     

Foveation-Based Error Resilience and Unequal Error Protection over Mobile Networks

By exploiting new human-machine interface techniques, such as visual eyetrackers, it should be possible to develop more efficient visual multimedia services associated with low bandwidth, dynamic channel adaptation and robust visual data transmission. In this paper, we introduce foveation-based error resilience and unequal error protection techniques over highly error-prone mobile networks. Each frame is spatially divided into foveated and background layers according to perceptual importance. Perceptual importance is determined either through an eye tracker or by manually selecting a region of interest. We attempt to improve reconstructed visual quality by maintaining the high visual source throughput of the foveated layer using foveation-based error resilience and error correction using a combination of turbo codes and ARQ (automatic reQuest). In order to alleviate the degradation of visual quality, a foveation based bitstream partitioning is developed. In an effort to increase the source throughput of the foveated layer, we develop unequal delay-constrained ARQ (automatic reQuest) and rate compatible punctured turbo codes where the punctual pattern of RCPC (rate compatible punctured convolutional) codes in H.223 Annex C is used. In the simulation, the visual quality is significantly increased in the area of interest using foveation-based error resilience and unequal error protection; (as much as 3 dB FPSNR (foveal peak signal to noise ratio) improvement) at 40% packet error rate. Over real-fading statistics measured in the downtown area of Austin, Texas, the visual quality is increased up to 1.5 dB in PSNR and 1.8 dB in FPSNR at a channel SNR of 5 dB.     

Bandwidth and region division for broadband multi-cell networks

A cell planning technique termed BRD (bandwidth and region division) is presented for overcoming interference, maintaining QoS (quality of service) and improving channel capacity over OFDM (orthogonal frequency division multiplexing)-based broadband cellular networks. Through an optimal combination of sectorization and zero padding, bandwidth and region division is achieved that minimizes the outage probability for forward-link cell planning. In order to verify the effectiveness of the proposed algorithm, a Monte Carlo simulation is performed over multi-cell environments.     

A practical approach for statistical matching of output queueing

We study a practical approach to match the performance of an output-queued switch statistically. For this purpose, we propose a novel switching architecture called a multiple input/output-queued (MIOQ) switch that requires no speedup for providing sufficient switching bandwidth. To operate an MIOQ switch in a practical manner, we also propose a multitoken-based arbiter which schedules the switch at a high operation rate and a virtual first-in first-out queueing scheme which guarantees the departure order of cells belonging to the same traffic flow at output. Additionally, we show that the proposed switch can naturally provide asymmetric bandwidth for inputs and outputs, which may be important in dealing with the links with different bandwidth demands. Finally, we compare the performance of an MIOQ switch with that of an output-queued switch and discuss the design criteria to match the performance of an output-queued switch.     

Data retention characteristics of sub-100 nm NAND flash memory cells

In contrast to the conventional theories, we have revealed that the most distinguished mechanism in the data retention phenomenon after Fowler-Nordheim (FN) stress in sub-100 nm NAND Flash memory cells is the annihilation of interface states. Interface state generation rate increases rapidly as the channel width of NAND flash cell decreases. Comparison of interface states and stress-induced leakage current (SILC) component during retention mode shows that the annihilation of interface states strongly affects data retention characteristics of the programmed cells.     

Synthesis and adsorption properties of gold nanoparticles within pores of surface‐functional porous polymer microspheres

Mesoporous polymer microspheres with gold (Au) nanoparticles inside their pores were prepared considering their surface functionality and porosity. The Au/polymer composite microspheres prepared were characterized by transmission electron microscope (TEM), X‐ray diffraction (XRD), and Brunauer–Emmett–Teller (BET) techniques. The results showed that the adsorption of Au nanoparticles could be increased by imparting the pore structure and surface‐functional groups into the supporting polymer microspheres (in this study, poly (ethylene glycol dimethacrylate‐co‐acrylonitrile) and poly (EGDMA‐co‐AN) system). Above all, from this study, it was established that the porosity of the polymer microspheres is the most important factor that determines the distribution and adsorption amount of face‐centered cubic (fcc) Au nanoparticles in the final products. Our study showed that the continuous adsorption of Au nanoparticles with the aid of the large surface area and surface interaction sites formed more favorably the Au/polymer composite microspheres. The BET measurements of Au/poly(EGDMA‐co‐AN) composite microspheres reveals that the adsorption of Au nanoparticles into the pores kept the pore structure intact and made it more porous. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5627–5635, 2004