Polyoxometalate/Cellulose Nanofibrils Aerogels for Highly Efficient Oxidative Desulfurization

Polyoxometalate (POM) presents great potential in oxidative desulfurization (ODS) reaction. However, the high dissolubility of POM in common solvents makes it difficult to recycle. Besides, the small specific surface area of POM also limits the interaction between them and the substrate. Depositing polyoxometalates onto three-dimensional (3D) network structured materials could largely expand the application of POM. Here, the surfaces of cellulose nanofibrils (CNFs) were modified with very few (3-Aminopropyl) trimethoxysilane (APTS) to endow positive charges on the surfaces of CNFs, and then phosphotungstic acid (PTA) was loaded to obtain the aerogel A-CNF/PTA as the ODS catalyst. FT-IR indicated the successful deposition of PTA onto aminosilane modified CNF surfaces. UV-VIS further suggested the stability of PTA in the aerogels. BET and SEM results suggested the increased specific surface area and the relatively uniform 3D network structure of the prepared aerogels. TGA analysis indicated that the thermal stability of the aerogel A-CNF/PTA50% was a little higher than that of the pure CNF aerogel. Most importantly, the aerogel A-CNF/PTA50% showed good catalytic performance for ODS. Catalysis results showed that the substrate conversion rate of the aerogel A-CNF/PTA50% reached 100% within 120 min at room temperature. Even after five cycles, the substrate conversion rate of the aerogel A-CNF/PTA50% still reached 91.2% during the dynamic catalytic process. This work provides a scalable and facile way to stably deposit POM onto 3D structured materials.     

Surface-anchoring zwitterionic antioxidant enables efficient,stable,and scalable all-perovskite tandem solar cells

Lead-halide perovskite photovoltaics(PVs)have achieved impressive progress in power conversion efficiencies(PCEs)over the past ten years,accelerating their step forward to next-generation commercial PV technologies[1].As a leading candidate for perovskite PVs,monolithic all-perovskite tandem solar cells(PTSCs)have achieved the best24.8%for small-area devices(0.049 cm^2)in 2019。     

激光激发水中产生超声波的实验研究

采用压电陶瓷水听器研究了Nd：YAG脉冲激光激发水中产生瞬态超声波的特性,给出了声压信号随距离的变化关系。研究结果表明：用激光产生水下声波是完全可行的。当观测点与光击穿区的距离r远大于柱体长度时,垂直于光传播方向的激光瞬态超声波幅值与r成反比;当观测点与光击穿区的距离r很小时,垂直于光传播方向的声压幅值与产成反比。此外,当激光入射角度发生变化,超声脉冲的幅值也随之发生变化,其幅值在激光束垂直入射的时候最大。     

实时嵌入式操作系统VxWorks结构分析和剪裁

本文通过对VxWorks操作系统软件结构的分析,总结出VxWorks在可剪裁性方面所进行的设计和优化。在此基础上,提出VxWorks的的剪裁方法和步骤。剪裁方法是目标程序分析法结合预编译宏的方式,对VxWorks源码的剪裁分为4个步骤,包括组件级剪裁、文件级剪裁、函数级剪裁和语句级剪裁。最后,本文提供了一个微小内核实时系统的剪裁实例说明。     

Poly(lactic acid) composites with poly(lactic acid)‐modified carbon nanotubes

This work reports the study of the effect of chemical functionalization of carbon nanotubes on their dispersion in poly(lactic acid). The nanotubes were functionalized by the 1,3‐dipolar cycloaddition reaction, generating pyrrolidine groups at the nanotube surface. Further reaction of the pyrrolidine groups with poly(lactic acid) was studied in solution and in the polymer melt. The former involved refluxing the nanotubes in a dimethylformamide/polymer solution; the latter was carried out by direct melt mixing in a microcompounder. The carbon nanotubes collected after each process were characterized by thermogravimetry and by X‐ray photoelectron spectroscopy, showing evidence of polymer bonded to the nanotube surface only when the reaction was carried out in the polymer melt. The composites with polymer modified nanotubes present smaller average agglomerate area and a narrower agglomerate area distribution. In addition, they show improved tensile properties at low CNT concentration and present lower electrical resistivity. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3740–3750     

A Novel Method for Calculation of Eigenmodes of Gyrotron Resonators

A new method for calculating the eigenmodes of gyrotron resonators is presented. With this method, the resonant frequency, Q-factor and field profiles of the eigenmodes are determined through finding the minimum value of a function of two variables, namely the resonant frequency and the Q-factor. Compared with the traditional calculation method, the new method predicts a significantly higher Q-factor of the eigenmodes.     

高效液相色谱法同时测定生物质乳酸发酵液中有机酸及糖类化合物

建立了高效液相色谱(HPLC)同时测定生物质乳酸发酵液中有机酸及糖类的分析方法。使用Bio-Rad Aminex HPX-87H色谱柱,以5 mmol/L的H2SO4为流动相,在柱温55 ℃,流速0.6 mL/min条件下,采用示差折光检测器进行检测。结果表明,该方法可在17 min内实现发酵液中各种有机酸和糖类化合物等的完全分离与定量,6种有机酸和3种糖类化合物在0.15～5.19 g/L范围内的线性关系良好,回归方程的线性相关系数在0.9998以上。将该法用于米根霉发酵液的检测,两个水平的加标回收率为96.91%～103.11%,相对标准偏差(n=6)为0.81%～4.61%。该法适用于微生物发酵液中多种有机酸和糖类的快速、高效分离和定量测定。     

An efficient synthesis of δ-glyconolactams by intramolecular Schmidt–Boyer reaction under microwave radiation

δ-Glyconolactams were first synthesized by the intramolecular Schmidt–Boyer reaction using corresponding δ-azidosugars as starting material. The reaction could be efficiently performed in good yields of 61–69% under microwave radiation in acid condition, providing an alternative protocol to iminosugar δ-lactam.     

Direct transition metal-free C-S bond formation: synthesis of 2-aminobenzothiazole derivatives via base-mediated approach

A general, efficient, and more practical protocol for the base-mediated intermolecular or intramolecular S-arylation leading to the 2-aminobenzothiazole derivatives is reported. Remarkably, all reactions were carried out under transition-metal-free conditions with good to excellent yields, rendering the methodology presented herein highly valuable from both environmental and economic points of view.