OTDM transmitter using WDM-TDM conversion with an electroabsorptionwavelength converter

An all-optical multiplexing technique using wavelength division multiplexing (WDM)-time division multiplexing (TDM) conversion with an electroabsorption wavelength converter has been proposed and demonstrated. The effectiveness of this WDM-TDM conversion technique for various pulsewidth settings was experimentally investigated. The fluctuation of the signal performance, which was inevitably caused by the coherent crosstalk between adjacent pulses in the conventional optical time division multiplexing (OTDM) technique, were successfully suppressed, even in the case of wide pulse duration. High Q-factor performance has been maintained for a wide range of duty ration from 36% to 74%. By introducing this technique to the optical time division multiplexer, a highly stable and high-quality 40-Gb/s optical signal can be effectively produced without generating the short pulse or setting two tributaries at orthogonal polarization states, and without introducing high-speed electronics for signal multiplexing. The WDM-TDM conversion with an electroabsorption wavelength converter was extended to 60-Gb/s operation by using three 20-Gb/s tributaries. A clear eye opening was confirmed for a waveform after the WDM-TDM conversion of the 60-Gb/s signal     

A study of three techniques used in the diffraction analysis ofshaped dual-reflector antennas

An examination is presented of three techniques used for the efficient computation of fields diffracted by a subreflector that has been shaped by geometrical optics synthesis. It is found that these techniques, which are based on the geometrical theory of diffraction (GTD), produce errors in the computed fields that are specific to shaped reflectors. These errors are examined for a reflector system shaped to produce maximum gain from a tapered feed illumination. The discrepancies are directly related to the caustic being located near an observation point of the GTD calculations. The errors found are localized, and they increase in magnitude as the caustic approaches the main reflector. In a general offset geometry, the location of the caustic may be located arbitrarily close to the main reflector given a prescribed output aperture distribution. For the specific case considered here-the common situation of shaping to produce maximum gain-the caustic is located near the edge of the main reflector and on the reflection shadow boundary. A local correction is derived which creates a uniform solution through the caustic and across the reflection shadow boundary. Away from this point the calculation recedes to the standard GTD solution     

Electromagnetic scattering by a straight thin wire

The traveling-wave energy, which multiply diffracts on a straight thin wire, is represented as a sum of terms, each with a distinct physical meaning, that can be individually examined in the time domain. Expressions for each scattering mechanism on a straight thin wire are cast in the form of four basic electromagnetic wave concepts: diffraction, attachment, launch, and reflection. Using the basic mechanisms from P.Ya. Ufimtsev (1962), each of the scattering mechanisms is included into the total scattered field for the straight thin wire. Scattering as a function of angle and frequency is then compared to the moment-method solution. These analytic expressions are then extended to a lossy wire with a simple approximate modification using the propagation velocity on the wire as derived from the Sommerfeld wave on a straight lossy wire. Both the perfectly conducting and lossy wire solutions are compared to moment-method results, and excellent agreement is found. As is common with asymptotic solutions, when the electrical length of wire is smaller than 0.2 λ the results lose accuracy. The expressions modified to approximate the scattering for the lossy thin wire yield excellent agreement even for lossy wires where the wire radius is on the order of skin depth     

Systematic characterization of Cl2 reactive ion etchingfor improved ohmics in AlGaN/GaN HEMTs

Pre-metal-deposition reactive ion etching (RIE) was performed on an Al_0.3Ga_0.7N/AlN/GaN heterostructure in order to improve the metal-to-semiconductor contact resistance. An optimum AlGaN thickness for minimizing contact resistance was determined. An initial decrease in contact resistance with etching time was explained in terms of removal of an oxide surface layer and/or by an increase in tunnelling current with the decrease of the AlGaN thickness. The presence of a dissimilar surface layer was confirmed by an initial nonuniform etch depth rate. An increase in contact resistance for deeper etches was experienced. The increase was related to depletion of the two-dimensional (2-D) electron gas (2-DEG) under the ohmics. Etch depths were measured by atomic force microscopy (AFM). The contact resistance decreased from about 0.45 Ωmm for unetched ohmics to a minimum of 0.27 Ωmm for 70 Å etched ohmics. The initial thickness of the AlGaN layer was 250 Å. The decrease in contact resistance, without excessive complications on device processing, supports RIE etching as a viable solution to improve ohmic contact resistance in AlGaN/GaN HEMTs     

Security issues for downloaded code in mobile phones

'Software defined radio' (SDR) is a technology that will appear in future generations of mobile phones, i.e. following the third-generation mobile phone technology that is currently being defined and developed. Early versions of 'pragmatic' SDR will allow the terminal to be reconfigured at any level of its protocol stack. Ultimately, the 'pure' SDR technology will allow a mobile phone or terminal to have its air interface software configured or reconfigured by other software (or software parameters) that have been downloaded to the terminal, e.g. over the air, or from a remote server via the Internet and one's personal computer (PC). A number of security issues arise with downloaded code that implements the air interface functions, and these may not be obvious simply from looking at the way PC software is updated on-line today. This paper starts with an outline of the code that allows a mobile phone to operate over a particular air interface. This sets the baseline for a discussion of the security issues surrounding the change of this code from one that is fixed and downloaded once only, to code that is reconfigurable during the life of a product.     

High-Frequency Variations in the Rotation of the Earth

We report here observational results demonstrating that a three-station network of properly distributed VLBI observatories can routinely determine UT1 with a formal standard error of ±0.05 ms of time, in an observing period of 24 h. We also report the results of a three-month series of daily observing sessions of only 1-h duration with a single interferometer, which produced estimates of UT1 with standard errors of ±0.1 ms. The UT1 values obtained from the 1-h observing sessions track smoothly between the points of the 24-h time series, and the combined time series shows that it is not unusual for UT1 to vary by 1-2 ms in periods of several days. Preliminary results of reprocessing the 24-h observing sessions in 2-h segments suggest that variations of 0.4 ms may occur on time scales of only 6-8 h.     

Error analysis: a tool for selecting travel demand models

In developing travel demand models it is generally assumed that the base-year data used in developing the parameters, as well as the forecasted data to be used as independent variables for the design year, are of acceptable quality. The purpose of this paper is to present the application of error propagation theory in assesing the predictive quality of one type of travel demand forecasting model (multinomial logit models) and to demonstrate how error considerations can be used as a tool for identifying the optimal model. The general conclusions of this study are that: (1) it is indeed possible to quantify errors in dependent variables in logit models as a consequence of errors in independent variables; and (2) error consideration can be used as a tool for identifying the optimal model from a set of candidate models. Further research is recommended to develop better insights into the phenomenon of error propagation so that the consideration of errors can be a factor in decisions on model selection.