Breaking a remote user authentication scheme for multi-server architecture

Lin et al., (2003) proposed a remote user authentication scheme for multi-server architecture. In this paper, we breaks this scheme by giving an attack. Our attack allows an adversary to impersonate any user in the system, as long as a single authentication message of that user is observed.     

一种微透镜阵列的研制

介绍一种利用表面张力的作用、以光纤作材料、用分离的自聚焦透镜制作微透镜阵型的方法，这种方法具有制作工艺简单、无须昂贵设备等优点，用此方法实际制作了具有良好连续面型的微透镜阵列，并对制作的微透镜阵列进行了测试，效果较好。     

基于WVD的防空雷达直升机信号特征分析

基于直升机目标旋转部件的调制模型，本文针对防空雷达提出了分析直升机信号特征的一种新方法——WVD法，并对直升机目标旋转部件调制回波信号在不同噪声情况下加以仿真分析，结果表明：用WVD分析雷达回波中直升机信号特征是一种非常有效的方法。     

溶胶-凝胶制备技术与新型催化材料Ⅲ.溶胶粒子表面修饰方法制备催化膜

提出用溶胶粒子表面修饰方法，结合溶胶凝胶技术制备无机催化膜．该方法的基本原理是利用合适的金属配合物在胶粒表面的吸附作用，经溶胶凝胶过程，将活性组分结合到无机膜中．实验测定结果表明：（ＮｉＥＤＴＡ）２－，ＶＯ－３，ＭｏＯ２－４，（Ｐｄ（ＮＨ３）４）２＋，ＰｄＣｌ２－４，ＰｔＣｌ２－６和ＲｈＣｌ３－６可用来修饰ＡｌＯＯＨ溶胶．以Ｐｄ／γＡｌ２Ｏ３催化膜的制备为例，经三次溶胶凝胶过程，可制得无裂缺的厚度为９μｍ的Ｐｄ／γＡｌ２Ｏ３催化膜，膜材料的平均孔直径为６ｎｍ，Ｐｄ被均匀地分布在膜的顶层，其平均粒径为２３ｎｍ．     

气压传动与控制在电子专用设备上的应用

气压传动与控制已成为电子专用设备研制过程中一项不可缺少的内容 ,必须进行合理的气动系统设计及其控制 ,选择相应的气动元件以满足设备的功能要求。概述了气压传动与控制在电子专用设备上的应用。     

A Reliability Analysis of Calculated Results for Odd-Even and Odd-Odd Nuclei in Relativistic Mean-Field Theory

We calculate the binding energies of Ni, Cu, Xe, Cs, Pt, Au, Np, Pu isotope chains using two interaction parameter sets NL-3 and NL-Z, and compared the relative errors of the even-even nuclei with those of odd-even nuclei and odd-odd nuclei. We find that the errors of binding energy of odd-even and odd-odd nuclei are not bigger than the one of even-even nuclei. The result shows that comparing with even-even nuclei, there is no systematic error and approximation in the calculations of the binding energy of odd-even and odd-odd nuclei with relativistic mean-field theory. In addition, the result is explained theoretically.     

Crystallographic report: catena‐Aqua(2,2′‐bipyrimidine)lithium(I) perchlorate

A lithium(I) coordination polymer has been formed from LiClO₄ and the 2,2′‐bipyrimidine (bpym) ligand in which each square pyramidal lithium(I) atom is coordinated in the basal plane by four nitrogen donor atoms derived from two bpym ligands and one water molecule at the apical position. These are connected into a layer structure via hydrogen‐bonding interactions involving the perchlorate anions. Copyright © 2004 John Wiley & Sons, Ltd.     

覆盖亚临界到临界区的制冷工质物性快速算法

为了在亚临界到临界点这个大范围内保证制冷剂物性计算的快速、稳定、可逆,提出将整个数据区间划分成若干个子区间分别进行隐式拟合,并且保证相邻子区间连接点处的连续与光滑,以及通过求分析解从隐式方程中得到显式物性计算式的方法.以美国国家标准局开发的程序REFPROP6.01的计算结果作为数据源,以R410A为例对该方法做了验证.得出快速物性计算公式的应用范围为饱和温度-60℃至临界温度,与NIST REFPROP 6.01的计算结果进行比较表明,计算速度快1500倍,平均相对偏差小于0.01%.     

Novel,organosoluble, light‐colored fluorinated polyimides based on 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)biphenyl or 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)‐1,1′‐binaphthyl

Two series of fluorinated polyimides were prepared from 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)biphenyl ( 2 ) and 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)‐1,1′‐binaphthyl ( 4 ) with various aromatic dianhydrides via a conventional, two‐step procedure that included a ring‐opening polyaddition to give poly(amic acid)s, followed by chemical or thermal cyclodehydration. The inherent viscosities of the polyimides ranged from 0.54 to 0.73 and 0.19 to 0.36 dL/g, respectively. All the fluorinated polyimides were soluble in many polar organic solvents, such as N,N‐dimethylacetamide and N‐methylpyrrolidone, and afforded transparent and light‐colored films via solution‐casting. These polyimides showed glass‐transition temperatures in the ranges of 222–280 and 257–351 °C by DSC, softening temperatures in the range of 264–301 °C by thermomechanical analysis, and a decomposition temperature for 10% weight loss above 520 °C both in nitrogen and air atmospheres. The polyimides had low moisture absorptions of 0.23–0.58%, low dielectric constants of 2.84–3.61 at 10 kHz, and an ultraviolet–visible absorption cutoff wavelength at 351–434 nm. Copolyimides derived from the same dianhydrides with an equimolar mixture of 4,4′‐oxydianiline and diamine 2 or 4 were also prepared and characterized. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2416–2431, 2004     

喷气Z箍缩内爆等离子体的雪铲模型

 在喷气Z pinch内爆等离子体研究中，雪铲模型是一种常用的、比较简单的物理模型。根据实验中提供的电流波形，负载线质量和初始半径，可以通过雪铲模型来估算内爆到心的时刻。根据一维运动方程和不同构形下的解析解以及部分实验结果相结合，讨论了雪铲模型的适用范围。数值计算的内爆时间和实验（Gamble II, Double EAGLE, BLACKJACK 5）测量值符合得较好。结果表明，雪铲模型在喷气Z pinch实验的负载优化设计研究中是很有参考价值的方法。